GSD WKCT2QM2501 WIFI plus BT Module Instruction Manual

GSD WKCT2QM2501 WIFI plus BT Module

Product Specification

• Model: WKCT2QM2501
• Product Name: WIFI+BT Module
• Standard: 802.11 a/b/g/n/ac
• Interface: USB
• Data Transfer Rate: Up to 866.7Mbps
• Modulation Method Frequency Band: GFSK,/4-DQPSK,8DPSK(bluetooth) DQPSK,DBPSK,CCK(802.11b) QPSK,BPSK,16QAM,64QAM with OFDM (802.11g) QPSK,BPSK,16QAM,64QAM with OFDM (802.11n) QPSK,BPSK,16QAM,64QAM with OFDM (802.11a) QPSK,BPSK,16QAM,64QAM,256QAM with OFDM (802.11ac)
• BLUETOOTH: 2402~2480 MHz
• Operation Mode
• Security
• Operating Voltage
• Current Consumption
• Antenna Type
• Operating Temperature
• Storage Temperature
• Humidity: 5 to 95% maximum (non-condensing)

Product Usage Instructions

Installation

1. Ensure your operating system is compatible with the module (Linux, Windows).
2. Connect the module to a high-speed USB 2.0 interface.
3. Follow the manufacturer’s instructions for driver installation if required.

Configuration

1. Access your device’s network settings.
2. Select the WIFI+BT Module as the network connection option.
3. Enter any necessary security credentials for the network.

Usage

You can now enjoy high-speed wireless internet connectivity and Bluetooth capabilities with the WIFI+BT Module. Roam freely while staying connected to your network and other Bluetooth devices.

FAQ

• Q: Is the WIFI+BT Module compatible with Mac operating systems?
  A: The module is compatible with Linux and Windows operating systems only.

• Q: What is the range of the Bluetooth antenna?
  A: The Bluetooth antenna operates within the frequency range of 2402-2480 MHz.

Product Descrition

The WKCT2QM2501 is a complete dual-band(2.4GHz and 5GHz)WIFI 2×2 MIMO module. This module provides a high level of integration with a dual-stream IEEE 802.11ac MAC/ base band /radio and Bluetooth 5.2.The WLAN operation supports 20MHz,40MHz and 80MHz channels for data rates up to 866.7Mbps. It fully complies with IEEE 802.11 a/b/g/n/ac feature rich wireless connectivity at high standards,delivers reliable,cost-effective, throughput from an extended distance.

Product Features

• Complies with IEEE 802.11b/g/n for 2.4GHz and IEEE 802.11a/n/ac 5GHz Wireless LAN.
• Bluetooth v5.2
• Two transmit and Two receive path(2T2R)
• Works with all existing network nfrastructure.
• Capable of up to 128-Bit WEP Encryption.
• Freedom to roam while staying connected.
• UP to 866.7 Mbps High-Speed Transfer Rate in 802.11ac mode of operation.
• Operating Systems：Linux,Windows
• Low power consumption.
• Easy to install and configure.
• High speed USB 2.0 interface
• ROHS compliant

Product Specification

QPSK,BPSK,16QAM,64QAM with OFDM (802.11g) QPSK,BPSK,16QAM,64QAM with OFDM (802.11n) QPSK,BPSK,16QAM,64QAM with OFDM (802.11a)

QPSK,BPSK,16QAM,64QAM,256QAM with OFDM (802.11ac)

Frequency Band| BLUETOOTH 2402~2480 MHz

WIFI

2.4G: 2412~2462 MHz

5G: 5180~5240MHz,5260~5320MHz,5500~5720MHz,5745~5825MHz

Operation Mode| Infrastructure
Security| WEP, TKIP, AES, WPA, WPA2
Operating Voltage| 3.3V±10%
Current Consumption| ＜1000mA
Antenna Type| PCB
Operating Temperature| 0 ~ 70°C ambient temperature
Storage Temperature| -40 ~ 80°C ambient temperature
Humidity| 5 to 95 % maximum (non-condensing)

NOTICE:

• please keep this product and accessories attached to the places which children can’t touch;
• do not splash water or other liquid onto this product, otherwise it may cause damage;
• do not put this product near the heat source or direct sunlight, otherwise it may cause deformation or malfunction;
• please keep this product away from flammable or naked flame;
• please do not repair this product by yourself. Only qualified personnel can be repaired.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS and DSS) and CFR 47 FCC Part 15 E (NII). It is applicable to the modular transmitter
This radio transmitter 2AC23-WKCT2Q has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
The concrete contents to check are the following three points.
Please refer to the table in section 2.7.
Should be installed so that the end user cannot modify the antenna

Feed line should be designed in 50ohm

• Fine-tuning of return loss etc. can be performed using a matching network.
• The antenna shall not be accessible for modification or change by the end user.
• The module complies with FCC Part 15.247 / Part 15.407 and apply for Single module approval.
• Trace antenna designs: Not applicable, the antennas for this module are integrated into the module. Use of external antennas or antennas integrated into the host circuit board are not an option.

BT/BLE Antenna:

2.4 G antenna:

5 G wifi：

• Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as “Contains FCC ID: 2AC23-WKCT2Q”; any similar wording that expresses the same meaning may be used.
• In accordance with FCC guidance it is recommended that the host product manufacturer perform investigative measurements to confirm that the system does not exceed the spurious emissions limits or band edge limits once the module is installed in the host system.
• If the host system contains other transmitters additional testing is required to check for emissions that may occur due to the intermixing of emissions with the other transmitters, digital circuitry, or due to the physical properties of the host product (enclosure). RF exposure assessments to account for transmissions across all transmitters that can operate simultaneously is also required.

For additional information refer to FCC KDB 996369 D04 Module Integration Guide.

• The host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.
• The host manufacturer is recommended to use FCC KDB 996369 D04 Module Integration Guide recommending as “best practice” RF design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties.
• This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.

Canada Statement

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 12290A-WKCT2Q” any similar wording that expresses the same meaning may be used.

the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Antenna type and antenna gain:

BT/BLE Antenna:

2.4 G antenna

5 G wifi

Notice to OEM integrator

• Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons.
• This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
• The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual(FCC/Canada statement).
• Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003.
• Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host.
• The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual.
• Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host.
• Must have on the host device a label showing Contains FCC ID: 2AC23-WKCT2Q or IC: 12290A-WKCT2Q
• Both FCC ID and IC ID are not to be placed on the host at the same time and only hosts going into the US can use the FCC ID and only hosts going into Canada can use the IC ID.

Installer should put it in the manual：
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>