GSD B70R150 Bluetooth Low Energy Soc Smart Module Instructions
- June 5, 2024
- GSD
Table of Contents
GSD B70R150 Bluetooth Low Energy Soc Smart Module
Product Description
The B70R150 is an ultra-low-power system-on-chip solution for Bluetooth 5.0 low energy module. This module combines the excellent performance of a leading RF transceiver with a low-power ARM Cortex-M4F and rich powerful supporting features and peripherals.
Product Features
- Embedded 32-bit CPU
- Supports 2Mbps LE.
- Frequency bands: 2400 MHz to 2483.5 MHz.
- Embedded ROM, 160kByte RAM, and 8MByte Flash Address Space.
- 4Kbits EFUSE for manufacturer use
- Embedded 4Mbits Flash and 160kB SRAM
- Supports GAP, ATT/GATT, SMP, L2CAP
- Supports OTA (Over-the-Air) programming
- Supports 8 channel Low power comparators
- ROHS compliant
Product Specification
| Model | Bluetooth Low Energy Soc Smart Module |
|---|---|
| Product Name | B70R150 |
| Standard | BLE5.0 |
| Interface | UART |
| Data Transfer Rate | 1,2Mbps |
| Modulation Method | GFSK |
| Frequency Band | 2400~2483.5 MHz |
| Frequency Range: | 2402~2480 MHz |
| Antenna Type: | PCB Antenna |
| Antenna Gain: | 3dBi |
| Operating Voltage | 3.0V±10% |
| Current Consumption | ＜200mA |
| Operating Temperature | -20 ~85°C ambient temperature |
| Storage Temperature | -40 ~ 80°C ambient temperature |
| Humidity | 5 to 95 % maximum (non-condensing) |
| Module size: | Length 16mm Width 12mm Height 2.7mm |
NOTICE
- please keep this product and accessories attached to the places which children can’t touch;
- do not splash water or other liquid onto this product, otherwise, it may cause damage;
- do not put this product near the heat source or direct sunlight, otherwise, it may cause deformation or malfunction;
- please keep this product away from flammable or naked flame;
- please do not repair this product by yourself. Only qualified personnel can be repaired.
FCC Statement
FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Integral PCB antenna with antenna gain 3.0dBi This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution:
The user is cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment. This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This modular complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter. If the FCC
identification number is not visible when the module is installed inside
another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains Transmitter
Module FCC ID: 2AC23-B70 Or Contains FCC ID: 2AC23-B70”
-
When the module is installed inside another device, the user manual of the host must contain the below warning Statements：
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. Any company of the host device which installs this modular with limited modular approval should perform the test of radiated & conducted emission and spurious emission,etc. according to FCC part 15C : 15.247 and 15.209 & 15.207,15B Class B requirement, Only if the test result complies with FCC part 15C: 15.247 and 15.209 & 15.207,15B Class B requirement， then the host can be sold legally.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>