QAZQA A05318 Hanging 5 Light Installation Guide
- June 28, 2024
- QAZQA
Table of Contents
QAZQA A05318 Hanging 5 Light
Product Information
Specifications
- I tem Number: A05318
- Voltage: 120V
- Maximum Wattage: LED, 25W
Product Usage Instructions
Item Number: A05318
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is LED, 25W.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
-
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts. -
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as
below picture
Installation Precautions:
- Installation by a licensed electrician is recommended.
- Read the instructions carefully and save them for future reference.
- Never start any work without shutting off the electricity.
Mounting Surface Preparation:
The mounting surface should be:
- Clean, dry, flat, and strong enough.
- 1/4 larger than the canopy on all sides.
- Correct any gaps exceeding 3/16 between the mounting surface and canopy.
Installation Steps:
- Check all parts and accessories are included.
- Turn off the power before starting installation.
- Remove the mounting plate and set it aside.
- Screw lock sleeves from lock nuts and press down canopy lock nuts.
- Pass cords through the mounting plate.
- Attach the mounting plate to the wall with screws.
- Drill holes for anchors, knock anchors in and secure the mounting plate to the wall with anchor screws.
Tools Required (Not Included):
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Cleaning Instructions:
To clean the fixture, use a soft cloth. Clean glass with a mild cleaner. Avoid
abrasive materials like scouring pads or steel wool.
Parts Included:
- (E) Mounting plate (1)
- (F) Canopy (1)
- (G) Lock nut (5)
- (H) Ball nut (4)
- (I) Cord (5)
- (J) Metal cover (5)
- (K) Screw (10)
- (L) Teardrop-shaped glass (5)
- (M) Quick link (1)
- (N) Rectangle shape slide buckle (5)
Accessories Enclosed:
- (A) Anchor (4)
- (B) Mounting screw (2)
- (C) Plastic Wire Connector (3)
- (D) Anchor screw (4)
- (K) Screw (2) (spare part)
Assembly & Installation Instructions:
For detailed assembly and installation instructions, please refer to the user
manual provided with the product.
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done. -
Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
-
Place the wall switch in the “OFF” position.
-
Unscrew ball nuts (H) from canopy (F).
-
Gently remove mounting plate (E) and then set them aside for later installation.
-
Please adjust the hanging height of the fixture :
-
Screw lock sleeves from lock nuts (G).
-
Press down and hold lock nuts (G) of canopy by hand.
-
Pull or push cords (I) in and out of canopy (F) to increase or decrease the hanging height.
-
Screw lock sleeves back to lock nuts (G) as shown in the illustration.
-
Please note that after adjusting the height of the fixture, please adjust rectangle shape slide buckles (N) to the bottom of canopy (F) with hands as shown in the illustration.
-
Carefully pass the supply wires from the outlet box through mounting plate (E). NOTE: To drill the holes in the wall for anchors (A), attach mounting plate (E) to wall with screws ( B & D )
-
Attach mounting plate (E) to outlet box and then mark the position of holes in the wall with a pen as shown in the illustration.
-
Drill holes and gently knock anchors (A) into the marked holes until anchors (A) are level with the wall.
-
Secure mounting plate (E) to the wall with screwing anchor screws (D) into anchors (A) and ,mounting screws (B) into holes of mounting plate (E).
-
NOTE: the side of mounting plate (E) marked “GND” must face out.
-
Make wire connections
Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the chart below
-
Twist wires together with plastic wire connectors until tightly joined.
-
Wrap each connector with approved electrical tape.
-
Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Connect wires according to the chart below -
Connect Black or Red Supply Wire to:
- Black
- *Parallel cord (round & smooth)
- Clear, Brown, Gold or Black without tracer
- Insulated wire(other than green) with copper conductor
-
Connect White Supply Wire to:
- White
- Parallel cord (square & ridged)
- Clear, Brown, Gold or Black with tracer
- Insulated wire(other than green) with silver conductor
- Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
-
-
- Open quick links (M), and then hang it onto a mounting plate (E) as shown in the illustration.
-
Position canopy (F) in place.
-
Carefully thread ball nuts (H) through the holes in the canopy (F) and mounting plate (E) and then secure them by tightening ball nuts (H).
-
- Align holes of teardrop-shaped glasses (L) and holes of metal covers (J), and then screw screws (K) into holes to secure the unit ( L & J ).
- Before installation, please loosen the screws (K) slightly first, and do not completely remove the screws.
-
Please adjust the hanging height of the fixture :
-
Screw lock sleeves from lock nuts (G).
-
Press down and hold lock nuts (G) of canopy by hand.
-
Pull or push cords (I) in and out of canopy (F) to increase or decrease the hanging height.
-
Screw lock sleeves back to lock nuts (G) as shown in the illustration.
-
Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!
Frequently Asked Questions (FAQ):
Q: Can I install the product without the help of a licensed electrician?
A: While it’s recommended to have a licensed electrician perform the
installation, if you have experience with electrical work and follow all
safety precautions, you can install it yourself.
Q: What should I do if my product is missing parts?
A: If any parts are missing, please contact the place of purchase for
replacement parts using the exact wording from the illustration in the manual.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>