Supa Cool 617827 16 Oscillating Stand Fan Instruction Manual
- June 28, 2024
- Supa Cool
Table of Contents
Supa Cool 617827 16 Oscillating Stand Fan
45 Watt 16″ Oscillating Stand Fan This manual is to be used with the following
SupaCool Fan: SCF16A
IMPORTANT: Read these instructions before use. Please retain for future
reference.
INSTRUCTION MANUAL
PARTS IDENTIFICATION
- (A) Front grille
- (B) Grille nut and screw
- (C) Fan blade
- (D) Rear grille fixing nut
- (E) Rear grille
- (F) Speed control switches
- (G) Motor housing
- (H) Oscillating button
- (I) Motor shaft
- (J) Blade retaining nut
- (K) Body
- (L) Power cord
- (M) Tube retaining screw
- (N) Height adjust inner tube
- (0) Tube clamp
- (P) Outside tube
- (Q) Base cap
- (R) Plastic base
- (S) Grille cover
ELECTRICAL SAFETY
RATING
- AC 220-240V ~ 50/60Hz, 45W.
- Plug the power supply into a suitable wall socket. Ensure that the voltage indicated on the identification plate corresponds with the mains voltage
- Important: Read these instructions fully before any assembly or use, and retain for future reference.
ASSEMBLY
- Screw the outside tube (P) onto the base end cap (Q) then clip the 4 base parts (R) into the base end cap (Q).
- Loosen the tube clamp (O) to adjust to the suitable height, then lock the tube clamp (0) on the height adjust inner tube (N).
- Put the body (K) into the height adjust inner tube (N), then use the tube retaining screw (M) to lock the body (K) together with the height adjust inner tube (N).
- Remove the blade retaining nut (J) and the rear guard fixing nut (D). Place the rear guard (E) onto the motor shaft (l) and use the rear guard fixing nut (D) to secure the rear guard (E)
- Place the fan blade (C) into the motor shaft (1), use the blade retaining nut (J) to secure the fan blade (C).
- Fix the grille cover (S) into middle of the front guard (A), and use the screw to tighten the grille cover (S) together with the front guard (A). Place the front guard (A) onto the rear guard (E), and use the front guard clips to fix securely onto the rear guard (E).
GENERAL SAFETY INFORMATION
- Do not connect the fan to the power supply until the fan is FULLY assembled
- Do not connect to any power supply other than 220-240V.
- Unplug the fan before any adjustment or cleaning is made.
- Never operate the fan if it has damaged or has worn parts. It should be returned to the manufacturer, service agent or a similarly qualified person for repair.
- Always position the fan on a stable, level surface.
- Do not spray anything into the fan.
- Do not use the fan near flammable areas or substances.
- To reduce the risk of electric shock, do not remove any screws.
- Do not insert fingers or other objects through the fan guard.
- Do not allow children to operate the fan.
- If the power cord is damaged, the fan must not be used and returned to the manufacturer, its service agent or similarly qualified person in order to avoid hazard.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
OPERATING INSTRUCTIONS
- Once the fan has been completely assembled, you can now plug into a mains socket.
- Turn the power on at the mains socket and then switch on the fan by pressing one of the three speed buttons on the control panel.
- Important: Always switch off the fan and unplug from the mains socket when not in use.
- To make the fan head oscillate, push down the oscillation button.
- To stop the oscillation pull the button up.
- The fan speed is controlled by pressing the push button switches.
- “O” Power off
- “1” Low speed
- “2” Middle speed
- “3”High speed
- To alter the height of the fan, release the tube clamp (0), extend the shaft to the desired height and retighten.
MAINTENANCE
- Before cleaning unplug the fan first.
- Clean the fan with a soft cloth and a neutral detergent.
- Add a few drops of high quality lubricating oil to the moto before first operation every year.
THANK YOU FOR PURCHASING
For a complete range of fans and air coolers please call or visit Supa Brands
for further information:
- Website: www.supabrands.co.uk
- Part of the extensive Supa Brand Range
- Helpline: 01473 237 997 PO
- Box 1042, Ipswich, IP1 9X)
DECLARATION OF CONFORMITY
MUNRO IMPORTERS LTD Declaration of Conformance In accordance with UK Government Guidance
- We, the importer: Munro Importers Ltd First Floor, Unit 1 The Quadrangle, The Drift, Nacton Road, Ipswich, Suffolk, IP3 90R
- Declare that the product: Product code: SCF16A – 617827 Product description: SupaCool 16″ Oscillating Stand Fan Is in conformity with the relevant statutory instruments and their amendments: EMC Directive 2014/30/EU and
- The Electromagnetic Combability Regulations 2016. Low Voltage Directive 2014/35/EU and The Electrical Equipment (Safety) Regulations 2016. Commission Regulation (EU) No 206/2012, Annex I – Implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to Eco-design requirements for air conditioners and comfort fans Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS) with its Amendments (EU) 2015/863.
- REACH Regulation (EC) No. 1907/2006 And is manufactured in accordance with the following Standard or standardized documents: IEC 62321-5 Edition 1.0: 2013, IEC 62321-5
- Edition 1.0: 2013, IEC 62321-4 Edition 1.1: 2017, IEC 62321-7-2 Edition 1.0: 2017, IEC 62321-7-1 Edition 1.0: 2015, IEC 62321-6 Edition 1.0: 2015, IEC 62321-6 Edition 1.0: 2015, IEC 62321-8 Edition 1.0: 2017, (EC) No. 1907/2006, EN IEC 55014-1:2021, EN IEC 55014-2:2021, EN IEC 61000-3-2:2019 +A1:2021, EN 61000-3-3 +A1:2019 +A2:2021 BS EN IEC 55014-1:2021, BS EN IEC 55014-2:2021, BS EN IEC 61000-3-2:2019 +A1:2021, EN 61000-3-3 +A2:2021 EN 60335-2-80:2003 +A1:2004 +A2:2009, EN 60335-1:2012 +A11:2014 +A13:2017 +A1:2019 +A14:2019 +A2:2019 +A15: 2021, EN 62233: 2008
All documentation is held on file and is available, on request from .
- This appliance is marked according to the UK Statutory Instrument 2013 No. 3113 on Waste Electrical and Electronic Equipment (WEEE) Regulations By ensuring this product is disposed correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The symbol on the product indicates that this product may not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
- Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
For a complete range of fans and air coolers please call or visit Supa Brands for further information:
- www.supabrands.co.uk
- 01473 237 997 Part of the extensive Supa Brand Range PO Box 1042, Ipswich, IP1 9XY
Read User Manual Online (PDF format)
Loading......