KASSA ROMAS KA S910 Scent Diffuser User Manual
- June 26, 2024
- KASSA ROMAS
Table of Contents
KASSA ROMAS KA S910 Scent Diffuser
INSTALLATION
- Take out the device, hold the upper atomization device (1), and rotate the essential oil bottle clockwise to separate it from the atomization device. ②
- Load essential oils (115ml, maximum). ③
- Tighten the essential oil bottle that containS essential oil counterclockwise with the atomization body and assemble it back into the entire machine. ④
- Plug in the outlet.
PRECAUTIONS
TOUCH PANEL DESCRIPTION
Operating instructions
Plug the device into a power outlet. When the device is powered on, the two-
color indicator lights up for 1 second, then only the red light is on, and the
chime reminds it to enter the standby state.
Panel function description:
By default, each time the diffuser is plugged in, it enters the standby mode. It will stay like this for a second and then the two-color indicator will show in red.
Touch mode (manual mode)
When the device is in standby mode, tap the control panel and the device enters first gear. If you touch the panel several times, the device will rotate in the first -second – third gears or – standby mode. In standby mode, the light shows red.
- Gear 1 : One gear light will light up; the chime will sound once to confirm. On this gear, the diffuser will work releasing scent for 15 seconds and pausing for 60 seconds in between. (The most fragrance released)
- Gear 2 : Two gear lights will light up; the chime will sound twice to confirm. On this gear, the diffuser will work releasing scent for 15 seconds and pausing for 120 seconds in between. (Middle fragrance released)
- Gear 3 : Three gear lights will light up; the chime sounds three times to confirm, and the third gear works for 15 seconds and pauses for a longer period of 180 seconds in between. (Least fragrance released)
The default working time for touch mode (manual mode) is 8 hours, and shifting between gears does not reset the timing. After 8 hours of working, the device enters standby mode and the standby mode kicks in showing the two-color indicator in red. The fragrance stops releasing until the user manually turns it on again at their desired time.
Bluetooth mode
While the device is in touch mode, in any of the gears, touch the control panel and press it down and hold for more than 3 seconds. A chime will confirm the device has now switched to Bluetooth mode; the Bluetooth light will show. It will now follow the settings and schedule you set up in the app. While In Bluetooth mode, if you wish to change back to touch (manual) mode, touch the control panel press it down and hold for more than 3sec. The chime will confirm the device has switched to touch mode and the gears will show. (Standby mode cannot directly into Bluetooth mode) When pairing with Bluetooth, the Bluetooth light flashes slowly but remains solid once the pairing is successful. Execute the work plan set by the APP in Bluetooth working mode. Each time the Bluetooth settings are changed on the APP, the Bluetooth light flashes quickly once and there is a chime to confirm the change took place. (See the separate APP instructions on the website)
MAINTENANCE
To ensure the best diffusing effect, please check and maintain the device every six months, or when you replace a new fragrance, or when the diffusing effect gets weak. Follow these steps:
- Take off the oil bottle.
- If using the same bottle that comes originally with the diffuser clean it with warm water and soap and make sure it is completely dry before you put in a new fragrance to avoid the fragrances mixing. The diffuser is waterless; make sure it is completely dry. (Do this step any time you are switching to a completely new fragrance)
- After cleaning the empty oil bottle, fill the bottle with a little alcohol and install it on the device, then run the device for about 5-8 minutes to clean the internal mechanism.
- After the device is clean, remove the device from the power outlet. Unscrew the bottle. Make sure to dispose of any alcohol remaining inside the oil bottle and dry it before putting in the new fragrance oil.
- Plug the device back in.