Silver Monkey SMXC039 Croft Case User Manual
- June 24, 2024
- SILVER MONKEY
Table of Contents
SMXC039 Croft
User manual
Before you use the product, please read the instruction manual carefully. Save it for future reference.
Safety Information
- Avoid direct contact of the device with water and other liquids.
- Do not use the appliance in an environment with high humidity.
- Keep the appliance out of the reach of children. They may swallow some of the elements.
- Use the appliance only in accordance with the operating instructions.
- If the device stops working properly – please contact us.
Contents
- Case
- Manual
- Mounting kit
Included Accessories
Item| Number of
pieces| Name| Use
---|---|---|---
| 19| (1)Screw of motherboard and SSDs.| Motherboard/SSD
| 6| (2)Screw of power supply and PCIE card.| PCIE Power
Supply/Expansion Cards
| 3| (3) Mounting pin| Motherboard mounting pin
| 8| (4)Screw for disks.| 3.5″ HDDs
| 1| Dowel attachment| For mounting the
motherboard pins
| 2| Plastic latch| Spare latch for panels.
| 8| Cable ties| To organize cables.
How to use the product
1.5 Panel I/O
Note! Before connecting the wires, refer to the motherboard manual.
1.6 Dismantling the panels
Glass Panel: Grasp the panel at the location marked (A). Bend the panel at a
15° angle, then lift upwards.
Side Panel: Using the tool-free screws (B), unscrew the panel and then slide
the panel towards you.
1.7 Assembling the power supply
Using the screws (2), screw the power supply to the chassis. Make sure the
power supply is facing the fan down the case.
Note! Before installing the power supply, check the location of the
screws in the power supply.
1.8 Assembling the
motherboard
Note! Before mounting, please refer to the motherboard manual.
The case supports motherboard standards: Mini-ITX, Micro-ATX, ATX.
To mount the motherboard, use the screws (1). Adjust the mounting pins (3) to
the size of your motherboard.
1.9 Removing the dust
filters
The housing is equipped with three dust filters. You’ll find them on the
front, bottom, and top of the case. The front filter has been integrated into
the front panel. To disassemble it, grasp the filter by the handle (A) and
then pull it towards you.
The upper and lower filters are fixed with magnetic strips. Gently prying them
open will allow them to be dismantled.
1.9
Mounting SSDs
Remove the side panel of the case as well as the bottom dust filter. Then, use
a screwdriver to unscrew the tray that is screwed on the bottom of the case.
To mount the drive, use the screws marked (1). You can install a maximum of
one 2.5″ drive. Screw the SSD to the top of the tray.
1.10 Mounting HDDs
Unscrew the disc tray. Use the screws (4) to mount 3.5″ HDDs. Screw the discs
into place.
Note! By mounting two 3.5″ HDDs, you lose the ability to mount a 2.5″
SSD.
1.11 Installation of fans and connection
Three 120mm fans are pre-installed on the front of the case. You can swap them
out for two 140 mm fans.
Note! Before removing the fans, we recommend unscrewing the drive tray –
this will make it easier to remove the fans.
You can mount one 120/140 mm fan on the back of the case.
You can install two 120 mm/140 mm fans on the top of the case.
1.12 Connecting
the fans
Note! There is no speed controller or fan backlight controller installed
in the case. The fans are connected to each other in parallel. Connect the fan
power to the SYS_FAN and connect the ARGB lighting to the port depending on
the board model: D-LED, ARGB, JRAINBOW, ADDR
1.14 Assembling the graphics card
Disassemble the glass panel. Unscrew the PCIE expansion card brackets. Use the
screws (2) to mount the graphics card.
Note! Remove as many PCIe port covers as required by your graphics card.
Installation of AIO water cooling **
**
You can install an All in One water cooling system in the case. The housing
factory supports radiator sizes: Front: 120 / 140 / 240 / 280 / 360 mm. Top:
120 / 140 / 240 / 280 / 360 mm. Rear: 120 / 140 mm.
Note! Before installing the water cooler, please refer to the enclosed
instructions. To mount a 360mm water cooler on the front of the case, we
recommend moving the drive tray.
Specification
| Side Panel | Tempered Glass |
|---|---|
| Backlight | ARGB |
| Motherboard Standard | Mini-ITX |
Micro-ATX ATX
Internal Storage Slots| 1 x 3.5″, 1 x 2.5″
Expansion Card Slots| 7
Maximum Graphics Card Length| 370 mm
Maximum CPU Cooling Height| 185 mm
Maximum number of fans| 7
Fan mounting options| Front: 3x 120 mm, 2x 140 mm
Top: 3x 120 mm, 2x 140 mm Rear: lx 120 mm
Water Cooling Mounting Options| Top: 120 mm, 140 mm, 240 mm, 280 mm, 360mm
Front: 120 mm, 140 mm, 240 mm, 280 mm, 360mm
Rear: 120 mm, 140 mm
Number of fans installed| 4
Buttons| Power Reset
Led out connectors| 2x USB 3.0 socket lx USB Type-C port lx Microphone jack lx
Speaker jack
Colour| Black
Height| 458 mm
Width| 230 mm
Depth| 475 mm
Scales| 7,3 kg
Warranty & Support
Your product comes with a 24-month manufacturer’s warranty. For more
information, visit the
www.silvermonkey.com/support website.
If you would like support on how to use the product, please contact us at
kontakt@silvermonkey.com.
Producer:
Silver Monkey sp. z o.o.
Twarda 18
00-105 Warsaw
Poland
v. 3/06.06.2024
Environmental & Compliance
As the manufacturer of this equipment, we declare that it meets the requirements of the relevant European Union directives. If you need a copy of the declaration of conformity – please contact us.
Do not dispose of this equipment with other waste. The materials from which the equipment is made can have a bad impact on the environment and human health if the product is disposed of improperly. Hand over used equipment to an appropriate e-waste collection point.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>