HOBBYWING X13-60KV-14S Brushless Power System User Manual

HOBBYWING X13-60KV-14S Brushless Power System

Thank you for your purchase. Please read the following statement carefully before use. Once used, it is considered to be an acceptance of all the contents. Please follow the manual instructions carefully during the installation. Modification may result in personal injury and product damage. We reserve the right to update the design and performance of the product without notice.

Introduction

The COMBO-XRotor-X13 brushless power system is a plant protection power system that adapts to a single-rotor load of 25-27kg/rotor. The maximum thrust of a single-rotor is 53kg+; it is suitable for a 50mm carbon fiber tube arm; the overall waterproof level is IPX6, and it is resistant to rain, rain pesticides, salt spray, high temperature, dust, impact, mud and sand resistance; the ESC uses FOC vector control, based on PMSM system algorithm optimization; the system has digital throttle and analog throttle, which can make the flight more stable; the system has power-on automatic detection, power-on voltage abnormal protection, over-current protection, stall protection and other protection functions; use CAN communication, with real- time data transmission; built-in fault storage function, and records fault data.

Safety Precautions

• When use it please keep away from crowds, high voltage cables, and obstacles and conform to safety regulations.
• Never approach to the high-speed rotating propeller & motor to avoid being injured by the propeller.
• Check all the component’s conditions before use. If there is any damaged component, please contact after-sale service for replacement.
• Check if the mounting screws, and all connecting parts before flight.
• Always make sure the motor is horizontal before flight.
• The X13 power system is connected to a circular tube arm with a diameter of 50mm.
• The color of the power system navigation light can be selected. After removing the light housing, you can select the desired color by flipping the dial switch.
• The CAN function can only be used when the flight controller has a CAN Channel.
• This function can be realized only when the flight controller has a CAN channel.
• There is no digital throttle for serial communication. Serial communication is optional for this power system.

Components of the Power System

• Motor x 1pcs
• ESC x 1pcs
• Propeller x 1pcs
• Motor mount x 1pcs
• please specify how many screws. fastening screw
• LED Set x 1pcs

Power system installation

• The whole power system has been assembled before leaves the factory. Unpack and take out the power system to install on the rack agricultural as per the rotation direction of the motor.
• The gray and red (yellow, red and green) cables are the data output. Upgrade signal wire (ESC system is upgradable) and digital throttle using the Hobbywing CAN protocol. The blank (yellow wire) is ground wire, the red wire is CAN-High( CH), and the gray(green) wire is CAN-Low( CL).
• The optional serial communication power system. Yellow, red and green cables are the data output and update signal line (the ESC system can be updated).
• The black and white is the PWM throttle wire, the black wire is the ground wire, and the white wire is the signal wire.
• The data signal line outputs in real time; the input and output throttle, motor speed, bus current, phase current, bus voltage, capacitor temperature, Mosfet temperature and other data.
• The throttle pulse width was fixed at 1050~1950µs.
• The CAN digital throttle needs to be adapted separately by the flight controller and the Hobbywing CAN protocol. Please obtain the protocol from Hobbywing sales, after-sales service, agents, flight control manufacturers, etc.

Specifications

• Recommend Take-off Weight: 25-27kg/rotor(54V, Sea Level)
• Recommended Battery : 12-14S LiPo(Max 61V)
• Maximum Thrust : 53kg+(54V, Sea Level)
• Operating Temperature: -20℃-50℃
• Mounting Arm Tube Outer Diameter : 50mm
• Protection Grade : IPX6
• Total Weight : 4257g( INC. prop)

ESC

• Continuous Current : 80A (Non-hermetic Ambient Temperature ≤60℃)
• Maximum Current: 200A (Non-hermetic Ambient Temperature ≤60℃)
• Recommended Battery : 12-14S LiPo
  Throttle Pulse Width : 1050-1950µs

Motor

• Stator Size : 13825
• Motor Size : 148*63.5mm
• KV: 60

Propeller

• Diameter Pitch : 56*20 inch
• Single propeller weight: 292g
• Weight (INC. adapter): 805g
• Support throttle Frequency: 50-500Hz

Parameters

Voltage (V)| Propeller| Throttle (%)| Thrust (g)| Ampere (A)| Power (W)| Speed (RPM)| Efficiency (g/W)
---|---|---|---|---|---|---|---

54

|

HW5620

| 32%| 9190| 13.2| 716.3| 992| 12.8
33%| 9456| 13.8| 745.1| 1006| 12.7
36%| 11189| 17.4| 941.2| 1092| 11.9
39%| 13104| 21.7| 1175.3| 1181| 11.1
42%| 15150| 26.7| 1445.2| 1270| 10.5
45%| 17295| 32.3| 1749.2| 1357| 9.9
48%| 19518| 38.6| 2086.1| 1441| 9.4
51%| 21811| 45.4| 2455.7| 1522| 8.9
54%| 24173| 52.9| 2858.5| 1600| 8.5
57%| 26609| 61.0| 3295.9| 1675| 8.1
60%| 29125| 69.7| 3769.9| 1749| 7.7
63%| 31726| 79.2| 4282.8| 1821| 7.4
66%| 34415| 89.5| 4836.6| 1892| 7.1
69%| 37186| 100.5| 5432.9| 1962| 6.8
72%| 40024| 112.3| 6072.3| 2031| 6.6
75%| 42902| 124.9| 6753.6| 2099| 6.4
78%| 45777| 138.2| 7472.6| 2165| 6.1
81%| 48588| 152.0| 8219.8| 2228| 5.9
84%| 51250| 166.1| 8976.8| 2287| 5.7
87%| 53657| 179.6| 9710.8| 2340| 5.5
90%| 55674| 191.8| 10368.9| 2385| 5.4
100%| 57398| 202.9| 10967.6| 2423| 5.2

Protective function

• Start protection： When the power is connected normally, the ESC will first start the self-test. If the self-test is successful, it will run normally after beeping. If the self-test fails, it will not start and the flashing light will act as warning sign.
• Stall Protection： When the ESC detects that the motor is locked, the ESC will completely turn off the output and will not restart the motor. At this time, it is necessary to power cycle to clear the error and restart the ESC to restore power output.
• Current protection： When it detects that the instantaneous current abnormality reaches close to 320A, the ESC will restart immediately, and the output will be turned off if the number of detections reaches 6 consecutive times. After the motor stops, it will return to normal after powering on again.
• Throttle signal loss protection: When the ESC detects that the throttle remote control signal is lost for more than 0.25 seconds, it will immediately turn off the output to avoid greater losses caused by the continued high-speed rotation of the propeller. After the signal is restored, the ESC will immediately restore the corresponding power output.
• Temperature protection: This power system has no temperature protection, and will only send out an alarm when the temperature of the ESC is higher than 110°C. The flashing lights will be 1 long and 3 short, and 1 long and 4 short. When the temperature exceeds 130 degrees, the ESC may be burnt. Upon seeing the prompt, please land immediately.

Warning tone description

recalibrate the throttle point

The motor fails to start after power on

|

“Beep, Beep, Beep” (2 seconds for each interval)

|

No throttle signal input on the receiver throttle channel

| Check if the transmitter and receiver is normal. Check if the wiring of the throttle channel is normal
The power-on voltage is lower than 24V or higher than 65V| “Beep, Beep , Beep” (1 second for each interval)| Battery voltage is too low or too high|

Replace with a suitable battery

Daily usage

Adjust LED light color
Use a tool to take out the M3×8 screws that fasten the led cover, and set the switches according to the corresponding light color below (factory default green). After setting the switches, assemble and fasten the LED cover.

Description of light color status

3 short flash

|

Over-current

| • Check the motor for foreign objects and check the propeller, then power on again

• Contact after-sales service

Single long flash

|

Throttle lost

| • Check the connection between the signal line to the flight controller

• Check whether the remote controller and flight controller are turned on

• Check the resistance of the black and white wires, if there is a short circuit, contact the after-sales service

Single long flash + Single short flash| Throttle not reset to zero| This problem occurs during the rotation of the motor. Please check the aircraft battery and circuit. There is a short circuit on the circuit.
Single long flash + 2 Short flash| Mosfet overheated (Over 110℃)| Cool down the power system and power on again
Single long flash + 3 Short flashes| Capacitor overheated (Over 110℃)| Cool down the power system and power on again

Single long flash + 4 Short flashes

|

Stall protection

| • Restart after the throttle is reset to zero

• Please check if there is any foreign matter in the motor, remove the foreign matter before starting

2 long flashes| ESC open-circuit| • Please check whether the motor circuit is intact| • Contact after sales service
2 long flashes + Single short flash| ESC short-circuit| • Please check whether the motor is in good condition| • Contact after sales service
2 long flashes + 2 Short flash| Motor short-circuit| • Please check whether the motor is in good condition| • Contact after sales service
2 long flashes + 3 Short flash| Phase A operational amplifier is abnormal| • Re-power on to return to normal| • Contact after sales service
2 long flashes + 4 Short flash| Phase B operational amplifier is abnormal| • Re-power on to return to normal| • Contact after sales service
3 long flashes| Phase C operational amplifier is abnormal| • Re-power on to return to normal| • Contact after sales service

Replacing the propeller

• Use the appropriate tools to take out the two propeller fastening screws and replace them with new propellers. If you need to replace the propeller clips, continue to take out the fastening screws and replace the whole set of propeller clips and propellers.
• Installing the propeller clip blades First, install the bottom cover on the motor, followed by the propeller blades, propeller gaskets, upper cover (propeller clips), and the final screws in order; pay attention to the installation of the propeller screws After clamping, the propeller should rotate freely, and make sure that the propeller clamp and the motor fastening screw are tightened and thread locker is used at the same time.

Firmware upgrade

There are two ways to update the firmware: online update via a computer or using flight control pass-through. The process using the flight controller pass through are as follows. This function uses DataLink data box, special DataLink software for the upgrade package, and a USB data cable. DataLink data box version requirements, LINK-01.2.14-C or higher version; DataLink software contact Hobbywing to obtain.

Note: Please ensure that the computer has already installed the Microsoft Visual C++ 2013 before or later using. An upgrade package contains only one program for each ESC. For other programs, please obtain a new upgrade package. For additional details, please refer to the DataLink user manual. The upgrade package can be obtained at the place of purchase; Hobbywing official website, dealers, Hobbywing sales, Hobbywing, and after-sales service. The FOC ESC will not support any other firmware, and can only be updated to the official firmware. Note: It can only be upgraded from the existing system. Software and hardware cannot be upgraded together.

CAN ESC upgrade

Connection
Connect the computer and the DataLink data box with a USB cable; ESC—->DataLink data box red gray( yellow red green)”—->”-CH1 CL1″

Software acquisition
It can be obtained at the place of purchase; Hobbywing official website, dealers, Hobbywing sales, and Hobbywing after-sales service.

Note: It can only be upgraded from the existing program, and software and hardware cannot be upgraded together.

Operation

ID set up

If there is no requirement, the default factory ID of the ESC is 1, the throttle channel is 1, and the base rate is 500kHz. This function is only available for CAN communication ESCs, and the serial port does not have this function. This function can communicate with the flight controller to realize digital throttle. This function requires the additional purchase of a DataLink data box. Before using this function, ensure that the computer system is installed with the Microsoft Visual C++ 2013 software in advance to operate.

Connection
ESC—->DataLink data box “red gray( yellow red green)”—->”-CH1 CL1″; Connect the data box to the computer via USB. Please remove the propeller to avoid danger upon changing the ID. For the same aircraft, different ESC IDs and throttles cannot be the same. ESCs with the same ID will be recognized as one ESC upon using the CAN function.

Operation

Fault storage
The ESC has its own fault storage function to store the time during power-on, flight time, and fault time information. This function makes it convenient for flight fault analysis. Please note that this function only records the data at the time of failure, and not all flight data. This function requires the use of a DataLink data box, serial port assistant, DataLink software, and USB data cable.

Note: DataLink software can be obtained from Hobbywing’s official website, dealers, Hobbywing sales, and Hobbywing after-sales. DataLink data box version requirements, LINK-01.2.14-C or later; serial port assistant requirements, USB to TTL; DataLink software requires a fault storage version, which can be obtained from the official website, WeChat official account or after-sales. The DataLink box has three power supply methods; USB data cable, serial port assistant, and external power supply cable. You can choose one of the power supply methods, and there is no need to use multiple power supply methods.

Note: For detailed steps, please refer to the DataLink user manual.

Connection
Serial assistant —-> DataLink data box “GND 5V TX RX” —-> “- + RX2 TX2”; CAN communication ESC —-> DataLink data box “□ red gray( yellow red green)” —-> “- CH1 CL1”, multiple ESCs can be used in parallel.

Note: Upon using multiple ESCs in parallel, the ID and throttle number must be set differently in order for one ESC to be recognized. Serial communication ESC—->DataLink data box “red gray( yellow red green)”—->”- D”, any channel of D1-D8 is acceptable, and it is recommended to use D1 channel first.

Note: This function requires the serial port assistant. Before using it, please ensure that the serial port assistant is in working condition. If it cannot be used, please replace the serial port assistant and try again.

After-sale maintenance

In the event that the equipment of the power system is damaged, please contact Hobbywing after-sales customer service immediately. Under the premise of not affecting the performance, make sure that you can use the Hobbywing power system kit accessories for replacement after contacting customer service. Users are prohibited from configuring accessories by themselves (such as screws, propeller clips, propellers) for replacement.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>