QAZQA YJ316 105679 Levant Fan 52 Inch LED Silver Instruction Manual
- June 22, 2024
- QAZQA
Table of Contents
QAZQA YJ316 105679 Levant Fan 52 Inch LED Silver
SAFETY INSTRUCTION
Please study the instruction manual and below information carefully before installing or using this product. Please keep this user manual for further reference
- The luminaires may only be installed by authorized and qualified technicians according the valid regulations for electrical installation.
- Maintenance of the luminaires is limited to their surfaces. During maintenance no moisture can come into contact with any areas of the terminal connections or voltage control parts.
- The electrical supply must be switched off at the outset, preferably by means of a switch in the distribution box, before any installation, maintenance or repair work is undertaken.
- Exterior lighting must not be installed during rain.
- Take account of the minimal separation distance from other objects and the room required around the fitting.
- If in any doubt, consult a professional, taking local installation requirements into account. Some countries stipulate that lighting may be installed only by registered installers.
- Clamping screws in electrical connections must be adequately tightened. This is particularly the case with 12V low voltage conductors.
- Clean with a clean, dry cloth or brush, use no solvents or abrasives. Avoid dampness on all electrical components
- Take account of all available technical information.
- Meaning of symbols This luminaire cannot be disposed together with normal domestic waste in standard rubbish can, but you have to bring it to a staging area for electrical waste
- Take note of the symbols when connecting wires:
(EN) This product contai ns a lig ht source of energy effi ciency class F
| QR| 8718881140136
---|---|---
Replaceable (LED only) light source by a professional.
Replaceable control gear by a professional.
INSTRUCTION FOR DC MOTOR CEILING FAN REMOTE CONTROL WIRING SCHEMATIC DIAGRAM FOR RECEIVER
POWER PARAMETER LIST
| Voltage | fan | lamp |
|---|---|---|
| I I 0-240V | 25W | I BW |
Adopt RF wireless digit emission technique, biunique controlled, coincident code rate is less than one millionth. (Emitter and receiver must be sent back to factory for maintenance if damaged.) Receiver can be controlled by any angles of the emitter in prescriptive space, unrestricted by direction. With the memory function, the controller can save the status(light and direction) while the supply power OFF and resume to the original after reload the power supply.
FUNCTION INSTRUCTION OF EMITTER
- Type number remote : RF433
- RF frequency range:433.92MHz
- Transmit power:7.75dBm
- Coverage area: 15m
KINDLY REMINDERS:
- Learning code matching mode is used between emitter and receiver. Turn “ON” the supply power within 30 seconds and press the emitter’s “FAN ON/OFF”button for 5 seconds, it can load normally after hearing a long sound “bee”, which means learing successfully and it can works normally.(PS:Learing mode is not accepted after turn “ON” the supply power for 30 seconds).
- When the emitter cannot control the receiver, please check the battery switch touching normally or not, correction of the positive and negative ,full or empty of the power.
- When the emitter cann’t control the receiver, please check is there any existence of similar remote controlled products nearby, then check whether they works, because remote controlled porduct with the same frequency will disturb each other.
- Low voltage of battery will affect the sensitivity of the emitter and the signal reception accordingly(the indicated light will flash out its warning when the battery get low voltage) , must replace if the battery is getting low voltage.
- Please take out the battery from the emitter when leavint unused for long time. 6. Supporting 18W lighting power at maximum. PS:Please conenct the ground wire correctly, otherwise it may cause the light micro-light or flash.
- When installing the fan, the fan ceiling cover don’t press the antennafor other wire), it is easy to breakdown the wire and short-circuited.
Simplified Declaration of Conformity: Hereby,FittinQBV declares that the radio equipment type [designation of type of radio equipment]] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.gazqa.nl
SAFETY PRECAUTION
IMPORTANT:PLEASE READ BEFORE INSTALLATION
- The installation work must be carried out by a qualified wiring installer.
- Turn off the Electrical Main Switch at the circuit breaker fuse box.
- Using power supply 220-240V/50Hz.
- When mouting the fan, to ensure the safety cable is loop across the ceiling mounting “J” hook.
- The ceiling mounting hook must be able to with hold a min.of 35 pounds.
- The ceiling fan must be mounted at a min height of 2.3meters of clearance from the floor.
- Do not insert any objects in the path of the blades.
- When all electrical connections are done, store all wires neatly.
- Make sure all screws and connections are tightly screwed and secured.
- The supply wires live and neutral must be connected to a double pole switch having a contact of at least 3 min in all poles.
WARNING
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADES BRACKETS DURING
ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT ANY OBJECTS IN THE PATH OF THE
BLADES. TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH AN
ISOLATION WALL CONTROL/SWITCH.
FAN STRUCTURE DRAWING
INSTALLATION OF LIGHTKITS:
- Remove one screw from the middle round piece,unscrew the other two screw out 3/ 4.
- Connect the light wire to the round piece:Black to Black,Blue to Blue.
- Pointing the lightkit two key hole to the unscrew two screws by pushing up,and turn the lightkit until it blocks by the screw.
- Fasten all the three screws ,make sure all are firmly.
- Carefully lift the Acrylic cover to the lightkit and twist clockwise until it is held tightly in place by three tabs.
Warning
Do not poke any objects or fingers through the protective screens
Do not place any objects, such as clothing, on the device
Be careful with long hair. These con be sucked in by the air flow, keep
sufficient distance.
INSTALLATION OF FAN BLADES:
- Install the blade to the motor housing by the supplied screws, make sure all the screws tighten firmly.
Warning
Do not poke any objects or fingers through the protective screens
Do not place any objects, such as clothing, on the device
Be careful with long hair. These can be sucked in by the air Aow, keep
sufficient distance.
INSTALLATION OF HANGER BRACKET:
- To use two Expansion Setscrew to install the hanger bracket firmly.
- To use four long screws to install the hanger firmly.
INSTALLATION OF DOWN ROD/HANGER BALL
-
Remove the screw and bolt from the hangerball as fig 3; Remove the “R” pin and cross pin from the down rod.
Notice : The downrod with hanger ball is 6 inch ,if it’s not enough ,please use the 10 inch rod before next step. -
Put the canopy and the decorative cover into the downrod,then thread the wire through the downrod.
-
lnstall back the screws and bolt to the hanger ball ,ensure to fasten the screws.
-
lnsert the down rod into the connector,loosen the two setscrews in the down rod support. Install back the cross pin and secured with the “R” pin.Fasten back the two setscrews .
-
The “R” pin must be properly installed to prevent the cross pin from working loose.
HANGING OF CEILING FAN
- Carefully lift the fan and assembly into hanger bracket which is attached to the outlet box.
- Ensure the rod ball’s groove is lined up with tab on the hanger bracket.
WIRING OF CEILING FAN
Total six color of wires connected from the top of the motor:
- Red: Live wire for fan(Ll)
- Brown: Live wire for fan(L2)
- Orange: Live wire for fan(L3)
- Black :Live wire for light
- Blue:Neutral wire
- Yellow&Green:Earth wire
- Connect the bracket sing I male end(yellow&green wire)to the motor single female end(yellow&green).
- Connect the motor 3 male and 2 male end to the remote control.
- Connect the remote control input 4 female end to the bracket output 4 male end.
NOTE:ALL THE MALE END AND FEMALE END MUST BE CONNECTED WELL TO ENSURE THE MOTOR AND REMOTE CONTROL WORK NORMALLY.
INSTALLATION OF CANOPY
- After done up the wiring.attach canopy to the hanger bracket by pushing up and twist to locate screws in the two key holes.
- Tighten the two screws firmly. (fig 9)
FittinQ B.V.
Smaragdweg 52, 5527 LB Hapert,
The Netherlands
www.qozqa.nl
FIHlnQ LTD
55 Baker Street,
London, Wl U 7EU
United Kingdom