maytronics 100 LIBERTY Robotic Pool Cleaner User Guide

maytronics 100 LIBERTY Robotic Pool Cleaner

Specifications

• Model : LIBERTY 100 | 200 | 300 | 400
• Type : Cordless Robotic Pool Cleaner
• Compliance : EU Directives 2014/35/EU, 2014/53/EU, 2014/30/EU, RoHS, REACH

Product Usage Instructions

Safety Instructions
Before using the LIBERTY Robotic Pool Cleaner, please read and adhere to the following safety instructions

1. Remove the robotic pool cleaner from the pool before allowing people to enter the pool.
2. Ensure the robotic pool cleaner is switched OFF when examining it.
3. Keep the robotic pool cleaner out of reach of children or individuals who may not be capable of using it safely.
4. Only use the original battery charger provided.

Getting Started
Follow these steps to get started with your LIBERTY Robotic Pool Cleaner

1. Place the battery charger at least 11 cm above ground for protection against electric shock.
2. Position the battery charger at least 3.5 m away from the pool edge during operation.
3. When cleaning the impeller, use the impeller safety tool as per the user manual.
4. Avoid placing hands near the impeller motor area and driving belt mechanism to prevent injury.

Maintenance
To ensure proper maintenance of your robotic pool cleaner

1. Do not use the cleaner if liquid flocculant or clarifier has been added to the pool water.
2. Do not open, crush, heat, or burn the battery case to prevent fire and burns.

FAQ

• Q: Can the Lithium-Ion battery in the LIBERTY Robotic Pool Cleaner be replaced?
  

  • A: No, the Lithium-Ion battery in this product is non-replaceable and should be recycled at certified electronics recyclers.

• Q: Where can I find more information regarding product compliance with EU Directives?
  

  • A: For full information on compliance with EU Directives and certifications, please contact us at www.maytronics.com/contact-us-en and request the EU Declaration of Conformity.

Robotic Pool Cleaner LIBERTY

LIBERTY 100 | 200 | 300 | 400

User Instructions

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

Please adhere strictly to following WARNINGS

1. Remove the robotic pool cleaner from the pool before allowing people to enter the pool.

2. When examining the robotic pool cleaner, make sure the robotic pool cleaner is switched OFF.

3. Charge the battery only in the temperature range between 6°C to 35°C / 43°F – 95°F.

4. Keep the robotic pool cleaner out of the reach of children or persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
   Cleaning and maintenance shall not be done by children.

5. Use only the original battery charger.

6. The battery charger must be supplied through a power circuit protected by a residual current device (RCD) having a rated residual operating current not exceeding 30mA.

7. The power cord is not user-replaceable. If the power cord is damaged, stop using the battery charger and contact the service center for repair. Do not use extension cord to connect the battery charger to electric supply; provide a properly located outlet.

8. DO NOT USE the robotic pool cleaner and/or its battery / power pack in case of mechanical damage to the robotic pool cleaner and/or its battery.

9. To avoid the risk of fire and burns, DO NOT open, crush, heat, or burn the battery case.

Please ensure that the following

PRECAUTIONS are implemented

1. For continuous protection against possible electric shock, place the battery charger at least 11 cm / 4 in above ground.
2. Position the battery charger at least 3.5 m / 12 ft from pool edge during operation.
3. When cleaning the impeller, use the impeller safety tool. See user manual.
4. Keep hands and fingers away from impeller motor area and driving belt mechanism to avoid injury.
5. When lifting the robotic pool cleaner, take care to prevent back injury.
6. Do not use the robotic pool cleaner if you have added liquid flocculant or any other clarifier to the pool water. These substances obstruct and damage the robot filters.

IMPORTANT SAFETY INSTRUCTIONS

The Lithium-Ion battery in this product is non-replaceable. It should be recycled at certified battery electronics recyclers that accept batteries. Batteries should NOT be discarded in the trash or put in municipal recycling bins. Do not disassemble the battery.
Impeller blades hazard
WARNING
Read User Instructions before servicing

This product complies with EU Directives 2014/35/EU, 2014/53/EU, 2014/30/EU, RoHS and REACH. For full information, please contact us at www.maytronics.com /contact-us-en and ask for the EU Declaration of Conformity.

SAVE THESE INSTRUCTIONS

Robotic Pool Cleaner LIBERTY

LIBERTY 100 | 200 | 300 | 400 Cordless Robotic Pool Cleaner

What’s in the Box

First time use

SPECIFICATIONS

Robot

• Water depth range : 0.3m – 3m / 1ft – 9.8ft
• Motor protection: IP 68
• Battery Lithium-ion | 5,000mAh | 25.2V ; 5Ah / 126Wh
• Radio communication:
• Bluetooth® 5.0 – 2402-2480 MHz – Maximum power 2.1mW

Water Conditions
Use the robotic pool cleaner only in the following water conditions

• Chlorine : 4 ppm max.
• pH: 7.0 – 7.8
• Temperature: 6°C – 35°C / 43°F – 95°F
• NaCl: 5000 ppm max.

Battery Charger

• Protection: IP54 (Raintight)
• Output: <30 VDC

FEATURES AND INDICATIONS

Cycle Selector – LIBERTY 300 & 400
Use Cycle Selector to customize cleaning mode to “Floor only”:

1. Press ON to activate until the LED lights up.
2. Press ON again for 3-6 seconds until the purple LED blinks 3 times. Place the robot in the pool, and within 30 sec, it will start working. After each cleaning cycle, the robot will return to default mode.

ClickUpTM – LIBERTY 300 & 400
Easily take the robot out of the pool by shaking the Clicker in the water for 3 seconds when the robot has finished the cleaning cycle. The robot will climb up its nearest wall and wait a few seconds to be picked up.

Eco Mode – LIBERTY 200, 300 & 400
Use Eco Mode to keep your pool floor clean for a week on one charge.
The robot will automaticly clean the pool floor for up to 40 min, three times a week.
LIBERTY 400 can also be set for 30 min four times per week or 60 minutes twice per week via the app.

1. Press ON to activate until LED lights up.
2. Press again for 5-8 seconds until the LED flashes purple and then green.
3. Place the robot in the pool, and within 30 sec, it will start working.

References

Pages: 1 2

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>