WATER TECH Precision V10 Cordless Vacuum Instruction Manual
- June 24, 2024
- WATER TECH
Table of Contents
- WATER TECH Precision V10 Cordless Vacuum
- IMPORTANT SAFETY INSTRUCTIONS
- SAFETY AND USAGE SYMBOLS
- FCC STATEMENT
- Product Breakdown
- Specifications
- Charging Your Cleaner
- Adding the Brushes
- Filter Assembly
- Attaching the Vacuum Head
- Attaching the Pool Pole
- Turning the Cleaner On and Off
- Shallow Water Cleaning
- Maintenance
- Frequently Asked Questions
- LIMITED WARRANTY
- DISPOSAL
- Contact
- Documents / Resources
WATER TECH Precision V10 Cordless Vacuum
READ AND SAVE THESE INSTRUCTIONS
WARNING: Read carefully and understand all safety warnings before operating. Failure to do so may result in serious personal injury.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNINGS AND USAGE INFORMATION
WARNINGS
-
Read carefully and understand all safety warnings before using this appliance.
-
Do not attempt to operate the cleaner or use the charger if any appear to be damaged in any way.
-
Never allow children to operate this product. This is NOT a toy, children should be supervised to ensure they do not play with this product.
-
Keep the cleaner and its accessories out of reach of children.
-
This cleaner is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
-
Keep proper footing and balance at all times when using the cleaner. Do not overreach.
-
Keep hair, loose fitting clothing and all body parts away from openings and moving parts of the cleaner.
-
Do not attempt to open any factory sealed on motor box to access the battery, motor or electronic assembly.
-
The warnings, cautions, and instruction discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood, the operator should always exercise intensive caution and common sense when utilizing the cleaner.
Warnings for Charging -
Use only battery charger model: LC099-3S2PK, LC099-3S2PK-CR to charge the battery.
-
Disconnect the cleaner from the battery charger or power main before performing and routine maintenance – such as, cleaning the filter or debris chamber.
-
Charge cleaner indoor only. Do not use or store the charger outdoors. Charge your cleaner in a clean, dry location.
-
Do not attempt to recharge the battery if the charger or connections are damaged in any manner.
-
Connect the charger to a power source through a residential current wall outlet with a ground fault circuit interrupter (GFCI). If in doubt, contact a qualified electrician.
-
Risk of shock. Do not use charger if charger is / was exposed to liquid, rain.
-
Make sure the cleaner and charging pins completely dry before connecting the charger and recharging the battery.
-
Do not plug or unplug charger into a power source or the appliance with wet hands.
-
Never service the cleaner while the unit is on or connected to the charger or the charger is connected to the power source.
-
Do not use any type of electrical extension cord. The charger must be plugged-in directly to the main power of a residential wall outlet.
-
Do not charge the cleaner near flammable or combustible substances.
-
Never attempt to pry open the charging adapter or connector plug.
-
If the cord on the charger is damaged in any way, the charger MUST be replaced with a charger certified by Water Tech for use with the cleaner to reduce the risk of shock or fire.
-
Remove the cleaner from the charger and power main after full charge time is reached as noted in the instructions.
Usage Information -
Use this product only for it’s intended purpose as described in this manual. Use only Water Tech accessories and filters.
-
Operating and charging temperature: Ambient and water 41˚ F / 5˚C and 100˚ F / 37.7˚ C
-
The Cleaner is designed for use UNDER WATER ONLY in pools and spas. The cleaner is not a vacuum for floors or surfaces in the home.
-
Submerge the cleaner in water immediately after turning the pump motor “ON” to prevent damage to the seals on the motor shaft. Failure to do so, will shorten the life of the water seals and /or void the warranty.
-
Never leave the cleaner in the water when the cleaner is “OFF” or when it has run out of power.
-
Avoid picking up sharp objects as they may damage the filter Keep all openings free of debris which could reduce water flow.
-
For details regarding battery recycling and disposal, refer to the section “BATTERY RECYCLE” “ DISPOSAL” in the instructions and contact your local authorities for more information.
-
This cleaner contains rechargeable batteries. Do not incinerate the battery as it will explode at high temperatures. Always dispose of batteries in accordance with local law.
-
The cleaner contains rechargeable, Lithium-ion batteries. Do Not incinerate the battery. The battery will explode at high temperatures. Always dispose of batteries in accordance with local laws.
- DANGER: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. When using electrical products, read, understand and follow all the instructions stated in this manual.
- WARNING: DROWNING HAZARD. This device produces suction. Risk of entrapment present. DO NOT use when bathers are present. Never permit children to use this product. Never permit persons who cannot swim to use this product to prevent the chance of drowning.
- DANGER: DO NOT ALLOW WATER OR OTHER HIGHLY CONDUCTIVE FLUIDS TO CONTACT THE CHARGER OR CHARGING JACK PRIOR TO OR WHILE CHARGING THE APPLIANCE. Pool water is highly corrosive and will cause damage to the charger or charging jack and can cause short-circuit resulting in smoke fire and/or serious personal injury. Make sure all surfaces of the charger and charging jack are dry and no water is present before charging the appliance.
- DANGER: NEVER LEAVE CLEANER UNATTENDED IN A CAR, TRUCK or MOTORIZED VEHICLE WHILE RECHARGING THE BATTERY. RISK OF FIRE. Operating temperature ambient and water 41˚ F / 5˚C and 100˚ F / 37.7˚ C.
- WARNING: RECHARGE ONLY WITH A CHARGER MANUFACTURED BY WATER TECH CERTIFIED FOR USE WITH THIS PRODUCT. A charger suitable for one type of battery pack may create a risk of fire when used with another battery pack. DO NOT use an extension cord or power strip. Use only charger certified by Water Tech: LC099-3S2PK, LC099-3S2PK-CR.
- WARNING: Never attempt to pry open the battery compartment. Risk of short circuit or fire.
- WARNING: Do NOT use this cleaner to pick up any toxic substance, flammable, combustible liquids. (e.g. gasoline) or use in the presence of explosive or flammable fumes.
SAFETY AND USAGE SYMBOLS
The following symbols and meanings are intended to help you operate the product better and safer. Please study them and learn their meanings.
SAVE THESE INSTRUCTIONS
FCC STATEMENT
Industry Canada Regulatory Information
CAN ICES-3 (B)/NMB-3 (B)
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation, If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
- Reorient or relocated the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different than that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Product Breakdown
Model: 50050PL
- Vacuum Head (Brushes)
- Brushes
- Wheels
- Vacuum Head Assembly
- Universal Vacuum Head Adapter
- Nose Cap
- Shallow Water Cleaning Adapter
- Multilayer Filter Bag
- Shell
- Charger
- Spring Clip
- Motor Box Assembly
- Sand & Silt Bag
- All-Purpose Filter Bag
- Shoulder Strap
- Car Charger
- EU Adapter
Warning: Only use the battery charger supplied with the cleaner.
Specifications
- Battery Charger Input …………………………………………………………..100-240V-50-60Hz, 800 mA Maximum
- Battery Charger Output ………………………………………………………………………………………..12.6V, 2.0A
- Water Temperature Range ……………………………………….Maximum 100°F, (37.7°C) Minimum 41°F, (5°C)
- Operation Depth ……………………………………………………Maximum 12 ft. (3.5 m), Minimum 10 in. (0.25 m)
- Charge temperature ………………………………………………..Maximum 100°F, (37.7°C) Minimum 41°F, (5°C)
ADDITIONAL PARTS AVAILABLE:
- Head and Hose Attachment (part No: P30X882)
To purchase, contact your retailer or call us at (732)-967-9888
Charging Your Cleaner
Initial Charge 6 Hours
- Recharging (After Complete Discharge) 6 Hours
- Maximum charging time should not exceed 12 Hours
Adding the Brushes
Brushes
- Brushes are added to the vacuum head. (Figure B)
- Different configurations are available. (6 Brushes Total)
Filter Assembly
Attaching the Vacuum Head
- (Figure D.1 without adapter)
- (Figure D.2 with adapter)
Attaching the Pool Pole
Turning the Cleaner On and Off
Shallow Water Cleaning
Connecting the Shallow Water Adapter
- Locate the Shallow Water Adapter and Precision Intake hose included with your unit.
- Take the Shallow Water Adapter and firmly push it onto the end of the Precision Intake until it clicks into place. You may need to twist it slightly to lock the connections.
- Once the Shallow Water Adapter is securely attached to the Intake, connect the other end of the Intake to the hose.
Starting the Cleaning Cycle
- Once the Shallow Water Adapter is connected to the Precision Intake and hose, place the entire Precision cleaner body into the water.
- Ensure the Precision cleaner is fully submerged under water. The body must be completely covered by water to generate proper suction.
Note: Do not operate the Precision cleaner unless the body is totally underwater. Running the unit out of water may damage the suction components.
Maintenance
Long Term Storage
- Always clean the Nose Cap and Filter Bag before storing.
- Always store and charge your cleaner in a cool, dry indoor shelter.
- Recharge the cleaner for 6 hours after each month of inactivity.
- Never leave your charger connected to the cleaner for more than 24 hours.
Cleaning the Filter Bag
- You should remove and clean the Filter Bag following each use. (Figure H.1)
- Don’t scrub the bag against itself while rinsing it. (Figure H.2)
Environmental Program(s), WEEE European Directive
Please respect the European Union regulations and help to protect the
environment.
Return non-working electrical equipment to a facility appointed by your
municipality that properly recycles electrical and electronic equipment. Do
not dispose them in unsorted waste bins. For items containing removable
batteries, remove batteries before disposing of the product.
Environmental Recycling Programs USA
- Help protect the environment.
Frequently Asked Questions
Q: Can my cleaner be run out of water?
A: Yes, for a short period of time when you turn it on before submerging into your pool or spa.
Q: When I am cleaning my pool how do I know when the cleaner is out of battery power?
A: Most people can feel the cleaner is running through vibration in the vacuum pole or handle. To be sure, you can lift it out of the water to hear if it is running or not.
Q: How often should I clean out my cleaner’s filter bag?
A: You can clean your filter bag as often as you like with no ill effects. The filter bag can then be turned inside out and rinsed with a hose or in a sink. Do not wash it in a washing machine or with detergent. For more detailed instructions, see “Cleaning the Filter Bag” instructions in this manual. For best results, do this after each use, or whenever you notice the performance of your cleaner declining.
Q: How can I stop dirt from coming out of the nozzle when I take the cleaner out of the water?
A: There are two ways to remove the unit from the pool when done cleaning: WHEN USING HANDLE: Lift from pool with the nose facing up to allow the water to escape from the back and sides. WHEN USING A VACUUM POLE: Remove the unit from the pool with the bottom facing upwards and the handle facing down. This will allow the water to escape and keep the dirt inside.
Q: Where can I buy replacement parts?
A: Look for original Water Tech replacement parts at your local retailer or call 1-(732)-967-9888 for more details.
Q: Will my pool chemicals hurt the cleaner?
A: This cleaner is designed to withstand pool chemicals during its usage period. However, it should be rinsed off with fresh water after it is removed from the pool. This will increase the life of the filter bag/seal ring.
Q: Can I leave the cleaner in the pool when not in use?
A: No. The cleaner should be removed from the pool and stored in a clean, dry place when not in use. This will increase the life of your cleaner and its accessories.
Q: What do I do if my cleaner does not vacuum?
A: Make sure your cleaner is completely submerged in the water and the air is out of the clear funnel. The cleaner is only designed to vacuum water and will not vacuum air. If that does not resolve your situation, please check the following: • Make sure the filter bag is clear of debris that may be obstructing the flow. • Charge your cleaner for at least 6 hours.
If none of the above help resolve the situation, please call our Customer Service Division at (732)-967-9888.
LIMITED WARRANTY
Water Tech Corp (“WT”) warrants this product, including supplied accessories
against defects in material or workmanship for the time periods as set forth
below. Pursuant to this Limited Warranty WT will, at its option (i) repair the
product to the original specifications or (ii) replace the product with a new
or refurbished product. In the event of a defect, these are your exclusive
remedies. For purposes of this Limited Warranty, “refurbished,” means a
product or part that has been returned to its original specifications.
All Water Tech Battery Powered Pool & Spa Vacuums. For a period of one (1)
year from the original date of purchase of the product, WT will, at its
option, repair or replace with new or refurbished product or parts, any
product or parts determined to be defective.
Accessories
- Included accessories are covered by this Limited Warranty for a period of (90) days from the original date of purchase of the product.
Instructions
Please retain the original box and internal packaging materials. To obtain warranty service, you must comply with the following requisite instructions:
- Visit Water Tech Corp’s Customer Support Department via web at www.wtrma.com. You will be guided through the correct process on how to obtain the required RMA# (Return Merchandise Authorization Number.) All customers must obtain an RMA number before any product will be accepted for warranty service. If you need additional assistance please contact us by telephone: (732-967-9888) or email: [email protected].
- Package the unit and the WT battery charger only ( if the unit requires a WT charger ) properly and securely in the original box.
- Attach your RMA number and Bar-Code you received from the website to the outside of the package. If you could not print the RMA number and bar-code from the website you must write your RMA number in thick black indelible marker on two sides of the box.
- Send the package by USPS or express courier of choice to: Water Tech Corp, 10 Alvin Court, East Brunswick, New Jersey 08816; (WT suggests you insure the contents of your package.) WT is not responsible for lost, stolen or damaged property in transit to WT.
Repair/Replacement Warranty
This Limited Warranty shall apply to any repair, replacement part or replacement product for the remainder of the original Limited Warranty period or for ninety (90) days, whichever is longer. Any parts or products replaced shall become the property of WT.
This Limited Warranty covers only product issues caused by defects in material or workmanship during ordinary consumer use; it does not cover product issues caused by any other reasons, including but not limited to product issues caused by acts of God, misuse, abuse, limitations in technology, or modification of or to any part of the WT product. This Limited Warranty does not cover WT products sold AS IS or WITH ALL FAULTS or consumables (such as batteries). This Limited Warranty is invalid if the factory-applied serial number has been altered or removed from the product. This Limited Warranty is valid only in the United States and Canada.
EXPRESS LIMITATION: THIS LIMITED WARRANTY ONLY APPLIES IF THE PRODUCT WAS PURCHASED FROM AN AUTHORIZED WATER TECH DEALER. THIS WARRANTY IS NOT TRANSFERABLE LIMITATION ON DAMAGES. WT WILL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. DURATION OF IMPLIED WARRANTIES. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION OF THIS WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations or how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This Limited Warranty gives you specific legal rights and you may have other rights, which vary from state to state.
DISPOSAL
END OF LIFE BATTERY DISPOSAL
The maintenance free, Lithium Ion battery in your unit must be properly disposed of in accordance to State and local law. To confirm if recycling is required; contact your local authority for information.
WARNING!
- Never attempt to disassemble a battery pack.
- Remove all personal items such as rings, bracelets, necklaces and watches when unwiring a pack from the vacuum unit.
- A battery can produce a short circuit current high enough to weld a ring (or like item) to metal causing a severe burn.
- Wear complete eye protection, gloves and protective clothing when removing the battery pack.
- Take care not to touch wires together or allow them to contact any metal items, which would cause sparking and/or short circuit the battery.
- Never smoke or allow a spark or flame in the vicinity of the battery or the cleaner. Batteries can generate gases which could possibly ignite.
- Do not expose to fire or intense heat as this may result in an explosion.
- CAUTION: If a battery leak develops, avoid contact with the leaking acid and place the damaged battery in a plastic bag.
- If acid comes in contact with skin and clothing, wash immediately with plenty of soap and water.
- If acid comes in contact with eyes, immediately flood eye with running cool water for at least 15 minutes. Get medical attention immediately.
How to remove the battery
- Recommended tools (not included): Flathead screwdriver, wire-cutters, electrical tape.
- Using a flathead screwdriver, pry open the clamp to break the seal. See first image.
- Take out the battery from the battery compartment. See second image.
- Use the wire-cutters, cut the wires near the battery. Make sure the wires do not come in contact with themselves.
- Finally wrap the wire ends with electrical tape. Dispose according to local recycling laws.
Contact
- 10 Alvin Ct., Suite 111
- East Brunswick, NJ 08816 – USA
- Tel: 732-967-9888 US, Canada & International
- Fax: 732-967-0070 US & International
- www.WaterTechCorp.com
Scan
Documents / Resources
|
WATER TECH Precision V10 Cordless
Vacuum
[pdf] Instruction Manual
50050PL, Precision V10 Cordless Vacuum, Precision V10, Cordless Vacuum, Vacuum
---|---