ideal lux Punto AP D24 Outdoor LED Wall Light Instruction Manual
- June 22, 2024
- ideal lux
Table of Contents
ideal lux Punto AP D24 Outdoor LED Wall Light
Product Specifications
- Model: Punto AP D24
- Power: LED 12W
- Voltage: 220-240V, 50/60Hz
- Colour Options: ANTHRACITE, BIANCO, COFFEE, NERO
- EAN Codes: 8021696313559, 8021696328522, 8021696328539, 8021696328546
- Light Source: 3000K, 300mA, 34V DC
- Manufacturer: IDEAL LUX s.r.l.
- Website: www.ideal-lux.com
Product Usage Instructions
Warning:
Installation:
- Follow the assembly instructions by reading the numerical progression.
- The lighting fitting should be installed by a qualified electrician.
This product is provided with a light source with efficient energy class of:
EAN Light Source Mode Energy Light
Source Light Source (V)
Efficiency (mA)
Class
| 8021696313559 | PUNTO D24 3000K | E | 300 mA | 34 V | DC |
|---|---|---|---|---|---|
| 8021696328522 | PUNTO D24 3000K | E | 300 mA | 34 V | DC |
| 8021696328539 | PUNTO D24 3000K | E | 300 mA | 34 V | DC |
| 8021696328546 | PUNTO D24 3000K | E | 300 mA | 34 V | DC |
Light Source Information:
- This product is provided with a light source with an energy efficiency class of E.
- The light source is replaceable by an end-user.
- The LED light source is also replaceable by an end-user.
- The light source should be replaced by authorized personnel only in certain cases.
Safety Instructions
Ensure to adhere to the following safety guidelines:
- The apparatus complies with European safety standards EN 60 598-1.
- For specific regulations, installation must be carried out by a qualified electrician.
- In case of external electric cable damage, it should be replaced by the manufacturer, retailer, or a qualified electrician.
- Always disconnect the power supply before starting any installation or maintenance work.
- The product contains parts that can become hot during operation.
- Use appropriate fastening accessories suitable for the material.
LEGENDA ICON
- Replaceable light source by an end-user.
- Replaceable LED light source by an end-user.
- Replaceable light source by authorized personnel only.
- Non-replaceable light source. Upon end of life of the light source, the whole product will be replaced.
- Replaceable control gear by an end-user.
- Replaceable light source by authorized personnel only.
- Upon end of life of the control gear, the whole product will be replaced.
SAFETY INSTRUCTIONS
- This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires not suitable for recessed on normally flammable surfaces.
- Luminaire not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps which do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
- Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety guaranteed by the main insulation and an additional protective conduc- tor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class Il Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
- Class III Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Totally protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
Frequently Asked Questions (FAQ)
Q: Is the LED light source replaceable by the end-user?
A: Yes, the LED light source is replaceable by the end-user as mentioned in
the user manual.
Q: What are the available color options for the Punto AP D24 model?
A: The available color options are ANTRACITE, BIANCO, COFFEE, and NERO.
Q: Where should I contact for technical support or further inquiries?
A: You can reach out to IDEAL LUX s.r.l. via their website at www.ideal-
lux.com or visit their warehouse during the
specified working hours.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>