ideal lux Cotton SP1 D13 Ceiling Lamp Instruction Manual
- June 22, 2024
- ideal lux
Table of Contents
ideal lux Cotton SP1 D13 Ceiling Lamp
Product specifications
- Model: Cotton SP1 D13
- Power: G9 max 1 x 4W LED
- Voltage: 220-240V, 50/60Hz
- Barcode: 8021696297781
- Color: BIANCO (White)
ASSEMBLY
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION. THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.
Warning Icons
Product Usage Instructions
Installation:
-
The installation of this lighting fixture must be carried out by qualified personnel.
-
Follow the assembly instructions in numerical order provided in the manual.
-
Ensure that the electrical connections are made by a qualified electrician.
Energy Efficiency:
This product is equipped with a light source classified with an energy
efficiency class of F.
Replaceable Parts:
-
The light source can be replaced by an end-user.
-
The LED light source can be replaced by an end-user.
-
The control gear can be replaced by an end-user.
Safety Instructions:
-
Comply with European safety standards EN 60 598-1.
-
Installation should be done by a qualified electrician as per regulations.
-
In case of damage to the external power cable, it should only be replaced by the manufacturer, dealer, or a qualified electrician.
-
Always disconnect the power supply before installation or maintenance.
-
Use appropriate fixing accessories and comply with regulations for spare parts.
This product is provided with a light source with efficiency energy class of: Energy Efficiency Class
LEGENDA ICON
- Replaceable light source by an end-user.
- Replaceable LED light source by an end-user.
- Replaceable light source by authorized personnel only.
- Non-replaceable light source. Upon the end of the life of the light source, the whole product will be replaced.
- Replaceable control gear by an end-user.
- Replaceable light source by authorized personnel only.
- Upon end of life of the control gear, the whole product will be replaced.
SAFETY INSTRUCTIONS
- This fitting is produced and tested in accordance with the strictest European safety standards EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician. Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories.
- Use screws and wall plugs suitable for the material to which they are fastened.
- Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires not suitable for recessed on normally flammable surfaces.
- Luminaire not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps which do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
- Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety guaranteed by the main insulation and an additional protective conduc- tor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class Il Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
- Class III Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Totally protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
Frequently Asked Questions
Q: Can the LED light source be replaced by the end-user?
A: Yes, the LED light source in this product is replaceable by the end-user.
Q: What should I do if the lamp does not turn on?
A: Check and replace the fuse if needed. If the issue persists, consult a
qualified electrician for further assistance.
Q: Is it safe to handle the product during installation?
A: Exercise caution as some parts of the product may become hot during
operation. Handle with care and follow safety guidelines.