BARSKA BC614 Keypad Portable Safe Instruction Manual
- June 14, 2024
- BARSKA
Table of Contents
BARSKA BC614 Keypad Portable Safe
Read all instructions before using this safe.
WARNING
- For security purposes, change the factory default code as soon as possible. The factory default code is 1234.
- Avoid leaving the door open and unattended; it will allow unauthorized individuals to reprogram the safe, gaining full access to the safe and contents.
- Store emergency keys in a secure place; NOT inside of the safe.
- Keep the area in front of the safe door clear; the safe door is spring-loaded and will pop open forward, be careful when opening the safe.
- Keep safe away from children.
NOTE: BARSKA is not responsible for any damages due to moisture.
NOTE: BARSKA is not responsible if the safe or its contents get lost or
stolen.
PARTS OF THE SAFE
- Key Access
- Indicator Lights
- Key Pad
- Initialization Button
- Battery Compartment
- Removable Shelf
OPENING THE SAFE WITH ACCESS KEY
- Insert access key in key access, and turn counter-clockwise to open.
- NOTE: Be careful when opening the safe; keep the area in front of the safe door clear.
- Remove the access key.
NOTE: Store keys in a secure place. NOT inside of the safe.
BATTERIES
- Remove the battery cover located on the inside of the safe under the keypad. (E)
- Insert 4 new Alkaline AA batteries into the battery compartment and pay attention to the polarity of the batteries.
- Replace the battery cover.
NOTE
Do not mix old and new batteries.
CREATING PERSONAL PIN CODE
Safe retains one 3-8 digit PIN code.
- With the safe open, press and hold the initialization button (D) located on the inside of the safe under the keypad for 3 seconds. The green indicator light will flash twice.
- On the keypad input your 3 – 8 digit pin code (press the initialization button when finished if the pin code is not 8 digits). The yellow indicator light will flash twice and 2 beeps will be heard. Re-enter your pin code (press the initialization button when finished if the pin code is not 8 digits).
Successful
Green Flash will be seen along with 2 beeps.
Unsuccessful
Red flashes will be seen along with several beeps. Lock-out mode is activated
when the wrong personal PIN code is entered 3 consecutive times. The alarm
will be triggered and will last 1 minute. Lock-out mode will last 2 minutes.
During this period, pressing any button is invalid.
TESTING PERSONAL PIN CODE
-
Enter in personal PIN code on the keypad. The Door will automatically unlock and open.
NOTE: Be careful when opening the safe; keep the area in front of the safe door clear.
NOTE : Be careful when opening the safe; keep the area in front of the safe door clear. -
Test a pin code that is not registered to make sure the safe does not open to complete the testing process.
OPENING & CLOSING SAFE WITH PERSONAL PIN CODE
OPEN
To open the safe, on the keypad enter in personal pin code. The door will
automatically unlock and open.
NOTE : Be careful when opening the safe; keep the area in front of the
safe door clear.
CLOSE
To close the safe, close the door and the door will automatically lock in
place.
LOCKOUT
Lock-out mode is activated when the wrong personal PIN code is entered 3
consecutive times. The alarm will be triggered and will last 1 minute. Lock-
out mode will last 2 minutes. During this period, pressing any button
is invalid.
CHANGING PERSONAL PIN CODE
Follow the steps in “CREATING PERSONAL PIN CODE”.
SOUND
Press and hold the #1 button until all the indicator lights flash to turn the
sound either on or off. See the reverse side for more information
VIBRATION ALARM
The safe will alarm for 1 minute when the safe is rattled.
VIBRATION ALARM ON
To turn on the alarm system: Press and hold the “#4” key for 3 seconds, and
you will see the red Indicator Light flash 5 times, indicating that the alarm
system is on. You can activate the alarm no matter whether the safe door is
open or closed.
VIBRATION ALARM OFF
Turn off the alarm system: open the safe with the correct PIN code.
Note: The vibration alarm will turn off when you open the safe with the correct pin code. Please activate the alarm system each time as needed.
LOW BATTERY WARNING
When batteries are low; the yellow indicator light will flash following the
green indicator light when operating the safe. Please change the batteries as
soon as possible. Follow the steps in “BATTERIES”.
NOTE: Safe may still be opened in a low battery state depending on
battery voltage. If the safe cannot be opened, please use the Access key. The
registered pin code remains stored.
MOUNTING
The safe may be mounted to the floor. The pre-drilled mounting holes are
located under the safe. DO NOT mount the safe without anchoring to the wall
behind the safe!
When mounting to a wall check the wall or cabinet for structural soundness.
- Check the location for concealed items such as wires, pipes etc.
- Get the appropriate anchors for the type of floor or wall you will be mounting the lock box to (wood, tile, concrete etc).
- Mark the surface to drill holes for the anchors you will be using.
- Drill the appropriate size hole for the anchors you will be using.
- Once mounted, test the strength to make sure the safe is securely mounted.
CARE AND MAINTENANCE
- If necessary use a damp cloth to clean the safe. DO NOT use chemicals or cleaning agents.
- Keep liquids away from the control panel. Spills on the control panel will cause damage and possibly electric shock.
- Secure safe in a proper area to prevent it from falling and causing damage or injury.
- DO NOT overstuff the contents of the safe, it can damage the motor mechanism or the contents.
- DO NOT disassemble the product. For all repairs and maintenance, contact BARSKA Customer Service.
- DO NOT place emergency keys inside of the safe.
1-YEAR LIMITED WARRANTY
SAFE
BARSKA warrants this new item to be free of original defects in material
and/or workmanship under normal use for twelve (12) months from the date the
product is received by the purchaser. This warranty does not include damage
caused by improper installation or maintenance. Damage from misuse, abuse,
accident (such as dropping), normal wear and tear, excessive fire, flood, or
acts of nature. Damage from service or repairs other than those performed by
BARSKA. Labour, cost and shipping charges for the removal and replacement of
defective parts beyond the initial twelve-month warranty period. All
transportation and shipping charges. Removing or altering the seal under any
circumstances will automatically void the warranty.
This warranty is limited to the original purchaser and is not transferable.
This warranty applies only to products purchased in the United States. Please
e-mail info@barska.com or call 1.888.666.6769 for
the Return Merchandise Number (RMA#) before any returns. The RMA number must
appear on the outside of the shipping package. The product must be packed
carefully and sturdily in its original packaging to prevent damage in transit
and returned freight pre-paid to:
BARSKA OPTICS
Repair Department
855 Towne Center Drive
Pomona, CA 91767
Please include all of the following when returning BARSKA products for service and/or replacement:
- Please write your complete details (Name, Address, Telephone#, E-mail address, RMA#, etc.)
- Purchase receipt or Proof of Purchase. (Original/Copy)
- A brief explanation of the defect
- A Check/Money Order of $20.00 to cover inspection, shipping and handling.
Please allow 6-8 weeks for delivery.
BARSKA will examine and test returned products and repair or replace defective
part(s) or units with new part(s) or a new unit if necessary within the
warranty period. Purchaser is required to remit the above charges to BARSKA
for return shipping and handling at the time the product is returned. If
repair is required after the warranty period expiration, the purchaser will be
charged for replacement parts and return shipping. BARSKA® Optics shall not be
liable for any consequential, incidental and/or contingent damages whatsoever.
We will not pay shipping, insurance or transportation charges from you to us,
or any import fees, duties and or taxes. This warranty supersedes all previous
BARSKA® Optics warranties.
2019 BARSKA® I Pomona, CA 91767, USA
(I) 888.666.6769 I (f) 909.445.8169 I www.barska.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>