ideal lux SP1D50 Carta Pendant 500mm Light Instruction Manual

ideal lux SP1D50 Carta Pendant 500mm Light

Product Information

• Specifications:
  • Model: Carta SP1 D50
  • Maximum Power: 1 x 25W
  • Socket Type: E27
  • Voltage: 220-240V, 50/60Hz
  • Colour: BIANCO
  • Barcode: 8021696226040

Product Usage Instructions

• Installation:
  • The installation of this lighting fixture must be carried out by qualified personnel.
  • Follow the assembly instructions in numerical order.
• Safety Instructions:
  • The fixture complies with European safety standards EN 60 598-1.
  • Installation should be done by a qualified electrician according to regulations.
  • Always disconnect the power supply before installation or maintenance.
  • Use appropriate fastening accessories for different materials.
• Other Safety Information:
  • The fixture is equipped with a fuse; if the lamp does not turn on, replace the fuse.
• Electrical safety classes:
  • Class I: Mandatory grounding
  • Class II: No grounding required
  • Class III: Low voltage, no grounding required Various protection levels against solid particles and dust ingress.

FAQs

• Q: Can I replace the LED light source in this fixture?
  • A: The LED light source in this fixture is non-replaceable, please do not attempt to disassemble it.
• Q: What should I do if the lamp does not turn on?
  • A: Check and replace the fuse in the fixture if needed.
• Q: Is grounding mandatory for this lighting fixture?
  • A: Grounding requirements vary based on the electrical safety class; follow the guidelines provided in the manual.

DIMENSION

FEATURE

ASSEMBLY INSTRUCTIONS

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION. THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.

SAFETY INSTRUCTIONS

1. This fitting is produced and tested per the strictest European safety standards (EN 60.598-1).
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
5. Always isolate power before commencing installation, maintenance or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors.
10. Luminaires are not suitable for recessed on normally flammable surfaces.
11. Luminaire is not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing the ceiling.
13. This fitting is only suitable for fixing the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
15. Only use lamps that do not exceed the maximum specified wattage.
16. Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
18. Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class I Electrical safety is guaranteed by the main insulation and an additional protective conduc- tor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
22. Class II Electrical safety is guaranteed by the main insulation and a double or reinforced insulation. Earthing is not necessary.
23. Class Ill Electrical safety is guaranteed by a very low power supply (less than 50 Volts). Earthing excluded.
24. Not protected.
25. Protected against solid objects greater than 50 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against solid objects greater than 2,5 mm.
28. Protected against solid objects greater than 1mm.
29. Dust protected.
30. Protected against dust infiltration.
31. Not protected.
32. Protected against vertically falling water drops.
33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.
34. Protected against rain.
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged immersion.
40. Luminaire is not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.

THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>