GRANBERG 115.3260 PDP Right Gloves Instructions

: June 21, 2024
: GRANBERG

Table of Contents

GRANBERG 115.3260 PDP Right Gloves
Introduction
Maintenance
Using Instructions
SIZES
Declarations
More Information
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GRANBERG 115.3260 PDP Right Gloves

GRANBERG-115-3260-PDP-Right-Gloves-product

Introduction

6 pairs

Cut and impact resistant gloves EX . Palm made of white goatskin.

Thumb base reinforcement made of black goatskin. Para-Aramid layer in the palm and fingers protects from cuts. Waterproof ™ PROTEX membrane and breathable thin polyester mesh liner keep ® hands dry. Spandex and powerful impact protection on the back. Hook and loop closure. Suitable for assembly work and outdoor tasks in wet weather involving risk of cut and impact injuries.

Storage/Transport: The gloves are first packed in plastic bags which are subsequently packed in cardboard boxes for transport and storage. Granberg recommends storing unused gloves in original packaging. Prevent direct sunlight.

Maintenance

Maintenance/Cleaning: Both new and used gloves should be inspected before use, and before putting them on to make sure that there is no damage to them. If in doubt, discard the gloves and select a new pair. Leaving the gloves in a contaminated condition may cause a deterioration of quality. Cleaning or disinfecting the gloves may also negatively affect quality. The performance characteristics of gloves that have been worn or cleaned/disinfected/laundered may differ from the performance levels declared.

Obsolescence: When stored as recommended, unused gloves will not suffer any change in their mechanical properties for up to three years from the date of manufacture. Service life depends on application and maintenance and cannot be specified. It is the responsibility of the user to ascertain the suitability of the gloves for the user’s tasks.

Using Instructions

Donning/Doffing: Select the right size glove for your hand. Hold the glove by the cuff with one hand. Align the glove thumb with your other hand thumb and slide your hand into the glove, one finger into each finger. Pull by the glove cuff and align fingers into the right position. Use the same procedure for the other hand. If gloves are not contaminated, pull by the fingertips to doff the gloves. If gloves are contaminated, hold the glove cuff and pull toward the finger until the gloves come off.

Please note: Inspect the gloves for damage before use. The gloves shall not be worn when there is a risk of entanglement with moving parts of machines. Gloves meeting the requirement for resistance to puncture may not be suitable for protection against sharply pointed objects such as hypodermic needles. Gloves containing latex may cause allergic reactions in case of hypersensitivity to latex. Seek medical advice if applicable. None of the raw materials used in glove, or process of manufacturing it, are known to be harmful to the user. Impact protection was assessed in knuckles area and not on fingertips. These gloves are intended to protect hands in working environments in accordance with EN 388:2016+A1:2018 and EN ISO 21420:2020. This product complies with ANSI/ISEA 105-2016 and ANSI/ISEA 138-2019. It is the responsibility of the user to evaluate and determine risks based on the intended application.

The gloves should only be used for applications declared suitable by the manufacturer. Risk should be evaluated keeping in mind the protection levels and the harmonized standards on which gloves are tested. The results of the tests should help in glove selection, however it must be understood that actual conditions of use cannot be simulated and it is the responsibility of the user, not the manufacturer, to determine glove suitability to the intended use. Further information may be obtained from manufacturer.

SIZES

SIZE 6/XS (EN 420:2003+A1:2009)

Abrasion resistance: (1-4)
Circular blade cut resistance: (1-5)
Tear resistance: (1-4)
Puncture resistance: (1-4)
TDM Cut Resistance: (A-F)
Impact protection: (P)
- 1/A = minimum requirement
- 4/5/F = maximum requirement
- X – not tested

The results are taken from the palm area of the gloves.
The protection level increases with performance class.

Sizes

GRANBERG-115-3260-PDP-Right-Gloves-fig-9

Declarations

This product is classed as Category II Personal Protective Equipment (PPE) according to PPE Regulation (EU) 2016/425 and as retained in UK Law and amened and has been shown to comply with this Regulation through the Harmonized Standards and Designated Standards EN ISO 21420:2020, EN 388:2016+A1:2018.

Notified Body responsible for EU Type Examination (Module B):

Name: SATRA Technology Europe Ltd.
Address: Bracetown Business Park, Clonee, Dublin D15 YN2P, Republic of Ireland.
Notified Body number: 2777

Approved Body responsible for UKCA Type Examination:

Name: SATRA Technology Centre Ltd.
Address: Wyndham Way, Telford Way, Kettering, Northamptonshire NN16 8SD, United Kingdom.
Approved Body number: 0321
Declaration of Conformity can be obtained from https://www.granberg.no/catalog/115.3260

Wear the products of suitable sizes to provide optimal level of protection and maximum grip. User must only choose the glove fitting the size of her/his hand.