BOSCH SMV4HVX00G Built In Dishwasher User Guide
- June 21, 2024
- Bosch
Table of Contents
- BOSCH SMV4HVX00G Built-In Dishwasher
- Product Usage Instructions
- Frequently Asked Questions
- Setting up Home Connect
- Overview of water hardness settings
- Setting the water softening system
- Programmes
- OVERVIEW
- How to use your appliance
- Cleaning filters
- Troubleshooting
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BOSCH SMV4HVX00G Built-In Dishwasher
Specifications
- Water hardness settings: Soft, Medium, Medium Hard, Hard
- Rinse aid capacity: Up to the max mark
- Detergent dispenser capacity: 50 ml, 25 ml, 15 ml
- Programme duration: Vary based on the selected program
Product Usage Instructions
Setting up Home Connect
- Install the Home Connect app on your mobile device.
- Scan the QR code with the Home Connect app to connect your appliance.
Overview of Water Hardness Settings
Refer to the table in the instruction manual for country-specific water hardness values.
Adding Special Salt
- Unscrew the lid of the special salt dispenser and remove it.
- Fill the dispenser with special salt just before starting a program.
Adding Rinse Aid
- Press the catch on the lid of the rinse aid dispenser and lift it.
- Add rinse aid up to the max mark in the dispenser.
Setting the Water Softening System
- Press the designated button to open the basic settings.
- Set the water hardness level by pressing the appropriate buttons.
- Save the settings by pressing a specific button for 3 seconds.
Programmes
Refer to the program data in the manual for the duration, energy consumption, and water usage.
Adding Detergent
- Add detergent to the dry detergent dispenser based on the recommended quantity.
- Close the lid of the detergent dispenser securely.
How to Use Your Appliance
- Load suitable tableware into the dishwasher after removing large food remnants.
- Add detergent to the dispenser.
- Switch on the appliance.
- Select the desired program.
- Start the program.
- Remove the clean tableware at the end of the cycle.
- To cancel a program, press a specific button for approximately 4 seconds.
Cleaning Filters
- After each wash, check and clean the filters for residue.
- Turn and remove the coarse filter for cleaning.
Frequently Asked Questions
Q: How often should I add rinse aid?
A: Refill the rinse aid dispenser whenever it is close to empty or as per usage instructions for optimal results.
Q: Can I use regular salt instead of special salt?
A: No, only use special salt, as recommended for dishwashers, to prevent damage to the appliance.
Before using it for the first time, read the instruction manual and the safety information it contains.
Setting up Home Connect
Tip: Connect your appliance to a mobile device. You can conveniently change all settings using the Home Connect app.
- Install the Home Connect app on your mobile device and follow the instructions.
- Scan the QR code with the Home Connect app.
Overview of water hardness settings
- You can find an overview of the water hardness values that can be selected here.
- A table of country-specific units can be found in the instruction manual.
Setting the water softening system
- Press .
- To open the basic settings, press
- Setup 3 sec. for 3 seconds.
- The display shows Hxx.
- The display shows set.
- Press Start repeatedly until the right water hardness has been set.
- To save the settings, press Setup 3 sec. for 3 seconds.
Programmes
- The program data has been measured in the laboratory according to European standard EN 60436.
- The consumption figures depend on the program and additional function selected.
- The running time will change if the rinse aid system is switched off or rinse aid needs to be added.
OVERVIEW
Adding special salt
To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the programme starts.
- Unscrew the lid of the dispenser for special salt and remove it.
- On initial start-up: Fill the dispenser right up with water.
- Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
- Place the lid back on the dispenser and turn to close.
Adding rinse aid
- Press the catch on the lid of the dispenser for rinse aid and lift .
- Add rinse aid up to the max mark.
- Close the lid of the dispenser for rinse aid.
- The lid clicks into position.
Adding detergent
- Add the detergent to the dry detergent dispenser.
- Close the lid of the detergent dispenser.
- The lid clicks into position.
How to use your appliance
- Load the tableware.
- Only clean tableware that is suitable for dishwashers. Remove large remnants of food from the tableware. Check that the spray arms can rotate freely.
- Add detergent.
- Switch on the appliance
- Select the program.
- Start the program Start.
- Remove the tableware at the end of the program.
- To cancel the program, press Reset for 4 sec. for approx. 4 seconds.
- The program is canceled and ends after approx. 1 minute.
Cleaning filters
- After each wash check the filters for residue.
- Turn the coarse filter anticlockwise 1 and remove the filter system 2.
- Pull down the microfilter to remove it.
- Press the locking catches 1 together and lift the coarse filter out 2.
- Clean the filter elements under running water.
- Re-assemble the filter system.
- Insert the filter system into the appliance and turn the coarse filter clockwise.
- Make sure that the arrow markings match up.
Cleaning spray arms
- Unscrew the upper spray arm 1 and pull down to remove 2.
- Pull up the lower spray arm to remove it.
- Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.
- Insert the lower spray arm.
- The spray arm clicks into position.
- Insert the upper spray arm and screw it firmly in place.
Clean wastewater pump
- Disconnect the appliance from the power supply.
- Remove the filter system.
- Scoop out any water.
- Prise off the pump cover using a spoon and grip it by the crosspiece.
- Lift the pump cover inwards at an angle and remove it.
- Remove any remnants of food and foreign bodies in the area of the impeller.
- Insert the pump cover 1 and press down 2.
- The pump cover clicks into position.
- Install the filter system
Troubleshooting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>