AURORA ST10241 24V LED Strip Installation Guide
- June 15, 2024
- Aurora
Table of Contents
AURORA ST10241 24V LED Strip
Specifications
| Product | LED STRIP EN-ST10241 |
|---|---|
| LED Drivers | AU-LED16T24CV, EN-LED7524, EN-LED9024CV |
| Metres per Driver | 1m, 5m, 7m respectively |
| Note | Strip Light is not suitable for dimming with Triac Mains drivers |
| Address | Aurora Limited, 6 Little Burrow, Burrowfields, Welwyn Garden City, |
AL7 4SW, United Kingdom
Document Version| EN-ST10241_v1_22
Installation Overview
Step 1: Power Connection
Toggle the switch to turn the LED strip on or off.
Step 2: LED Flexible Strip Details
Cut points are provided every 50mm on the EN-ST10241 LED Flexible Strip.
Step 3: Bending the Strip
When bending the LED strip, ensure that the bend angle is greater than 60 degrees.
Step 4: Connection Types
- 4A: Standard connector
- 4B: Wired connector and flexible inter-connection lead
Step 5: LED Driver and Connector
LED driver and connectors are sold separately. Align the strip and clip into the connector, ensuring correct polarity.
Step 6: Bending Attention
Do not bend the LED strip at 90 degrees as it may damage the strip.
Step 7: Connector Installation
Align the connector and push into place, making sure that the polarity matches (black to black and red to red).
Step 8: Strip Alignment
The strip should be aligned correctly within the connector for a secure fit.
Step 9: Final Connection
Ensure the LED strip is firmly connected to the power source.
Installation Instructions
The LED strip operates at 24V DC. Ensure that the polarity is correct when connecting to any LED driver or connector. The strip should be switched off at the mains before commencing installation or maintenance. LED driver and connectors should be installed following the electrical connections are tight with no loose strands. For runs of over 10cm, connect individual lengths in parallel.
IMPORTANT INSTALLATION INFORMATION
-
Installation should be carried out by a qualified electrician in accordance with the latest edition of the National wiring regulations. The LED Strip operates at 24V DC.
-
A 24V DC LED Driver is required (not included).
-
When connecting to an LED 24 V Driver, ensure that the polarity is correct. The strip may be damaged if connected incorrectly.
-
Before commencing installation or maintenance, ensure electricity is switched off at the mains.
-
Ensure that ALL electrical connections are tight with no loose strands, including factory connections.
-
Basic insulation for SELV operation only, mounting surface of LED module
-
These LED Strips are dimmable with a 1-1 OV driver. Not suitable for mains Triac Dimming
-
To install the LED Driver please refer to their own instructions.
-
A maximum of 1 Om of can be connected in a continuous length.
For runs of over 10m connect individual lengths in parallel. -
The EN-ST1024B is used to connect the strip to a 24 V DC driver.
Align the connector and push into place. – Connect the wires from the connector to the LED driver; ensure that the polarity is correct. -
The EN-ST1024A/C is used to join two pieces of strip together: The strip must be cut at a cut-point. Push the ends of the strip to be connected together into the EN-ST1024A/C connector, Ensure that the polarity matches, i.e Black to Black and Red to Red.
-
Ensure when applying strip to surface, it is smooth and clean
Environmental Protection (W.E.E.E.) -Aurora’s WEEE Reg.No. WEEJBG0130YX (UK
Only)
waste Elecbical & Electronic Equipment Regulations (WEEE) requires that any of
our products showing this marking Oell) must not be disposed of with other
household or commercial waste. Aurora does not levy any WEEE disposal charges
to i1s customers for affected WEEE-related products. To prevent possible harm
to the environment or human health from uncontrolled waste disposal, please
separate any such product from other – waste types and recycle ii responsibly
at your local facilities. Check with your Local Authority, Recycling Centre or
retailer for recycling advice. 11, when you purchased any Aurora product, your
supplier included a WEEE disposal fee, you should then contact your supplier
for advice on the fake back of the product for the correct disposal.
GUARANTEE
This product is guaranteed for 3 years from the date of purchase. The guarantee is invalid in the case of improper use, installation, tampering, and removal of the Q.C. date label, installation in an improper working environment or installation not according to the current edition of the National Wiring Regulations. Should this product fail during the guarantee period it will be replaced free of charge, subject to correct installation and return of the faulty unit Aurora does not accept responsibility for any installation costs associated with the replacement of this product. This wananty is in addition to the statutory rights in your country of purchase. Aurora reserves the right to alter specifications without prior notice.
Environmental Protection and Warranty
The Aurora LED strip comes with a guarantee period of 3 years from the date of purchase, subject to terms and conditions. It must not be disposed of with general household waste and should be recycled according to local regulations. For further instructions on recycling, contact your local authority or retailer.
Important Environmental Regulation Compliance:
The Aurora LED strip complies with the WEEE (Waste Electrical & Electronic Equipment) regulations, which require that products like this should not be disposed of with general household waste and should instead be recycled at designated collection facilities.
This document is for the Aurora LED strip model EN-ST10241, version 1.22, and provides information on installation, usage, and environmental considerations for users in the United Kingdom.
FAQ
What is the maximum length I can use with one LED driver?
It depends on the LED driver model. The AU-LED16T24CV supports 1m, EN-LED7524 supports 5m, and EN-LED9024CV supports 7m.
Is the LED strip dimmable?
These LED strips are dimmable with a 1-10V driver. They are not suitable for mains dimming with Triac Mains drivers.
How do I ensure the correct polarity when connecting?
Ensure that the polarity matches, black to black and red to red, when connecting the strip to a power source or LED driver.
Can I bend the LED strip?
Yes, but you must ensure that the bend angle is greater than 60 degrees. Do not bend at 90 degrees to prevent damage to the strip.
What should I do if the LED strip does not turn on?
Check the connections for correct polarity and secure fit. Also, ensure that the LED strip is properly connected to the power source and that the power source is switched on.
Aurora Limited 6 Little Burrow, Burrowfields, Welwyn Garden City, AL7 4SW, United Kingdom
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>