MAXIM LIGHTING 88826WTNAB DAISY 60 Inch 5 Blade Fan With LED Light Kit Instruction Manual

MAXIM LIGHTING 88826WTNAB DAISY 60 Inch 5 Blade Fan With LED Light Kit

INSTRUCTION MANUAL

Lamping | Ampoule:”1 x PCB In Tergared LED 12W”

Before Getting Started

• Read the instructions carefully prior to assembling the product.
• When you open the package with a sharp tool like a box knife, be careful not to damage the components inside.
• Carefully remove all packaging materials and retain for future use.
• Keep all hardware parts and packaging out of reach or small children.
• Choose a clean, level, spacious assembly area. Avoid hard surfaces that maydamagethe product.
• Ensure that you have all required contents for complete assembly.
• Take care when lifting. Assemble the product in close proximity to where you intend to install it.
• Do not over tighten the screws and bolts as this may damage the threads.
• Do not let children play with this product.

Risk of suffocation!

Keep packaging materials away from children.

Lamp Care Instructions

Carefully read through the instruction sheet before assembly and using the product.

Caution there is a risk of shock!

Disconnect from power source before assembling or cleaning.

Switch off, unplug and allow bulb to cool before replacing bulb or cleaning.

Only use the recommended bulb type and do not exceed the maximum wattage as it could cause fire.
Check the product cord to be sure is free torn or frayed.

Cleaning & Maintenance

• On polished finishes, often using talc powder can reduce the appearance of fingerprints and other smudges.
• For respective shade surfaces, use the appropriate cleansers, i.e. glass cleaner, stone polish, & wood polish.
• Clean with soft cloth and a mild detergent. Do not use abrasive or harsh cleaners.
• Periodically (every 90-180 days) make sure that the screws are fully tightened.
• Prolonged exposure to heat sources may cause glazing, melting and scorching, or even cause color to fade.

Safety Information

1. To reduce the risk of electric shock, ensure the electricity has been turned off at the circuit breaker or fuse box before you begin.

2. All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation shoule be performed by a qualified licensed electrician.

3. The outlet box and support structure must be securely mounted and capable of reliably supporting 35 lbs. (15.9kg). Use only UL Listed outlet boxes marked “Acceptable for Fan Support of 35 lbs.(15.9kg) or less.”
4. The fan must be mounted with a minimum of 7 ft. (2m) clearance from the trailing edge of the blades to the floor.

5. Do not operate the reversing switch while the fan blades are in motion. You must turn the fan off and stop the biades before you reverst the blade direction.

6. Do not place objects in the path of the blades.

7. Electrical diagrams are for reference only. Lighe kits that are not packed with the fan must be UL-listed and marked suitable for use with the model fan you are installing. Switches must be UL General Use Switches.Refer to the instructions packaged with the light kits and switches for proper assembly.

8. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on ine side of the outlet box.

9. All setscrews must be checked and retightened where necessary before installation.

NOTE: These are approximate measures. They do not include the Amps and Wsttage used by the light kit.

WARNING:To reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades.

WARNING:Remove the rubber motor stops on the bottom of the fan before installing the blades or testing the motor.

WARNING:To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.

WARNING:To avoid possible electrical shock, turn the electricity off at the main fuse box before wiring. lf you feel you do not have enough electrical wiring knowledge or experience, contact a licensed electrician.

WARNING:Electrical diagrams are for reference only. Optional use of any light kit shall be UL-listed and marked suitable for use with this fan.

WARNING:To reduce the risk of fire, electric shock, or personai injury, mount to outiet box marked “Acceptable for fan Support of 35 lbs.(15.9kg) or less,” and use the screws provided with the outlet box.

CAUTION:To reduce the risk of personal injury, use only the screws provided with the oufiet box.

CAUTION:To avoid personal injury or damage to the fan and other items, use caution when working around or cleaning the fan.

NOTE: These are approximate measures. They do not include the Amps and Wsttage used by the light kit.

TOOLS REQUIRED

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

PACKAGE CONTENTS

Installation

MOUNTING OPTIONS

WARNING :To reduce the risk of fire, electric shock, or personai injury, mount to outiet box marked “Acceptable for fan Support of 35 lbs.(15.9kg) or less,” and use the screws provided with the outlet box. An outlet box commonly used for the support of lighting fixtures may not be acceptable for fan support and may need to be replaced. lf in doubt, consult a qualified electrician.

If your ceiling fan does not have an existing UL-listed mounting box, then install one using the following instructions:

• Disconnect the power by removing the fuses or turning off the circuit breakers.
• Secure the outlet box directly to the building structure. Use the appropriate fasteners and materials. The outlet box and support structure must be securely mounted and capable of reliably supporting 35 lbs. (15.9kg). Use only UL Listed outlet boxes marked “Acceptable for Fan Support of 35 lbs. (15.9kg) or less.” . Do not use a plastic outlet box.

The illustrations below show three different ways to mount the outlet box.

NOTE: You may need a longer downrod to maintain proper blade clearance when installing on a steep, sloped ceiling. The maximum angle allowable is 30°away from horizontal.

If the canopy touches the downrod, then remove the decorative canopy bottom cover, and turn the canopy 180° before attaching the canopy to the mounting plate.
To hang your fan where there is an existing fixture but no ceiling joist, you may need an installation hanger bar as shown above.

Assembly – Attaching the Fan Blades

1 Attaching the fan blades

• Remove the screws (BB) from the Fan-motor assembly (F) and install the blade by tinhtning the screws. Attach a blade (H) to the fan motor housing (F) by inserting the blade (H) into the slot in the side of the fan motor housing (F) .
• Install the blade by tighten each screw (BB) securely.
• Repeat steps for the remaining blades (H).

2 Assembling the fan & Routing the wires

WARNING: Failure to properly install the locking pin could result in the fan becoming loose and possibly falling.

• Route the wires exiting the top of the fan motor (F) into the decorative motor collar cover (E)
• Make sure the slot openings are on top and route the wires through the canopy (C) and then through the ball/downrod assembly (B).
• Loosen, but do not remove, the setscrew (PP) on the collar on top of the motor housing (F).
• Aling the holes at the bottom of the downrod (B) with the holes in the collar on top of the motor housing (F).
• Carefully insert the hanger pin (CC) through the holes in the collar and downrod (B) . Be careful not to jam the hanger pin (CC) against the wiring inside the downrod (B).
• Insert the locking pin (DD) through the hole near the end of the hanger pin (CC) until it snaps into its locked position.
• Re-tighten the setscrew (PP) on the collar on top of the motor housing (F).

3. Attaching the fan to the electrical box

WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked “Acceptable for fan support of 35 lbs. (15.9kg) or less”, and use screws provided with the outlet box.

• Pass the 120-Volt supply wires through the center hole in the mounting bracket (A).
• Install the ceiling mounting bracket on the outlet box by sliding the mounting bracket (A) over the two screws (UU) provided with the outlet box. lf necessary, use leveling washers (not included) between the mounting bracket (A) and the outlet box. Note that the flat side of the mounting bracket (A) is toward the outlet box. When using close-to-ceiling mounting, it is important that the mounting bracket be level.
• Securely tighten the two mounting screws (UU).

4. Hanging the fan

• Carefully lift the fan-motor assembly (F) up to the slide-on mounting bracket (A).
• Insert the ball portion of the ball/downrod assembly into the socket of the slide-on mounting bracket.
• Turn the ball/downrod assembly clockwise until it is seated with the tab of the slide-on mounting bracket aligned with the slot in the ball.

WARNING: The locking slots of ceiling canopy are provided only as an aid to mounting. Do not leave the fan assembly unattended until all four canopy screws are engaged and firmly tightened.

5. Making the electrical connections

WARNING : Each wire nut supplith this fan is designed to accept up to one 12-gauge house wire and two wires from the fan. lf you have larger than 12-gauge house wiring or more than one house wire to connect to the fan wiring consult an electrician for the proper size wire nuts to use.

IMPORTANT : Use the plastic wire connectors (BB) supplied with your fan. Secure the connectors with electrical tape and ensure there are no loose strands or connections.

• The fan comes with 18 in. Lead wires for use with an extended downrod assembly. lf using the 6 in. Downrod assembly (B) provided, you can cut the lead wires to your desired length (no shorter than 18 in.) This will make extra room in the canopy (C) , if you do not wish to cut the wires, you will need to neatly wrap them.
• Connect the fan motor green wires to the household green or bare wire using a wire connecting nut (BB).
• Connect the fan motor white wire to the household white wire using a wire connecting nut (BB).
• Connect the fan motor black and blue wires to the household black wire using a wire connecting nut (BB).
• Secure each wire connecting nut using electrical tape.
• Turn the wire connecting nut (BB) upward and push the wiring into the Junction box.

6. Mounting the fan-motor assembly (standard mount)

WARNING:When using the standard ball/downrod mounting, the tab in the ring at the bottom of the mounting bracket must rest in the groove of the hanger ball. Failure to properly seat the tab in the groove could cause damage to the wiring.

WARNING :The locking slots of ceiling canopy are provided only as an aid to mounting. Do not leave the fan assembly unattended until all four canopy screws are engaged and firmly tightened.

• Align the locking slots of the ceiling canopy (B) with the two screws .in the mounting bracket (A) . Push up to engage the slots and turn clockwise to lock in place. Firmly tighten the two mounting screws.
• Install the Decorative plate (C).

7. Installing and glass bowl

WARNING: Do not overtighten when installing the glass shade into the light kit assembly. Allow the glass shade to cool completely before removing.

Place the glass bowl (G) into the light kit assembly (F) , aligning the three flat areas on the top flange of the glass bowl (G) with the three raised dimples in the light kit assembly. Turn the glass bowl (G) clockwise until it stops.

8. Installing No Light Bottom cap

Place the Bottom cap (I) into the light kit assembly (F) , aligning the three flat areas on the top flange of the Bottom cap (I) with the three raised dimples in the light kit assembly. Turn the Bottom cap (I) clockwise until it stops.

Dual-Slide Ceiling Fan Wall-Mounted Control Installation Instruction

1. IMPORTANT POINTS TO REMEMBER:

Read carefully before attempting to install this electrical device and retain the instruction for future reference.
1. Please note that all fixed wiring appliances should be installed by a qualified electrician.
2. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box or circuit breaker panel before wiring.
3. Do not mount wall control near heat producing equipment.
4. Use of this control with some ceiling fans could result in fire, shock and serious personal injury. Use this speed control only with capacitor speed controlled ceiling fans.
5. Make certain no bare wires are exposed outside the connectors.
6. This unit is to be used for the control of ceiling fans at AC120V 60Hz power supply only.

2. INSTALLATION INTRUCTIONS

Disconnect the power and remove the existing wall plate and switch.

1. Set all knobs on the dual slide wall-mounted control in the OFF position.
2. Installation of this control requires that a three-conductor cable with ground wire be run between the control wall box and the ceiling fan outlet box. (Figure 1)
3. Make wire connections and secure with wire nuts supplied, refer to figure 2.

• Connect black wire from A.C. power supply to black wire from the wall-mounted control.
• Connect black or red wire from the ceiling fan to black wire from the wall-mounted control.
• Connect blue wire from the ceiling fan to blue wire the wall-mounted control.

4. Secure the wall-mounted control to the outlet box with two screws provided. (Figure 3)
5. Secure the face plate over the wall control with two screws provided.

NOTE
If your ceiling fan would be used with the original pull chain switch, please always have the fan switch set to high speed and the light switch set to on position before using the wall control. To avoid accidental pull chain use, shorten chain by cutting it 1” below switch body.

FUNCTION:

Fan switch:

-: POWER OFF

• 1: HIGH SPEED
• 2: MEDIUM SPEED
• 3: LOW SPEED
• 4: L. LOW SPEED

Light Switch:

-: POWER OFF

When you push the knob upward slowly, the lightness of light will turn brighter and brighter.

Care and Cleaning

WARNING: Make sure the power is off before cleaning your fan.

• Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.
• Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor, or the wood , or possibly cause an electrical shock. Use only a soft brush or Iint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
• You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a light application of shoe polish.
• You do not need to oil your fan. The motor has permanently-lubricated sealed ball bearings.

Troubleshooting

• Check the main and branch circuit fuses or breakers.
• Chech the line wire connections to the fan and switch wire connections in teh switch housing.

The fan is noisy.|

• Ensure all motor housing screws are snug.
• Ensure the screws that attach the blade bracket to the motor hub are tight.
• Ensure the wire nut connections are not rattling against each other or the interior wall of the switch housing.
• Allow a 24-hour “breaking in” period. Most noises associated withe a new fan disappear during this time.
• If you are using the Ceiling Fan light kit, ensure the screws securing the glassware are tight. Check that the light bulbs are also secure.
• Ensure the canopy is a short distance from the ceiling.It shoulb not touch the ceiling.
• Ensure your outlet box is secure and rubber isolator pads were used between the mounting plate and outlet box.

The fan wobbles.|

• Check that all blade and blade arm screws are secure.
•  Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure from a point on the center of the blade to the point on the ceiling. Rotate the fan until the next blade is positioned for measurement, and measure from the same point on each blade to the ceiling. Repeat for each blade. Any measurement deviation should be within 1/8 in. Run the fan for ten minutes. If the minutes. If the fan continues to wobble please contact Customer Service and a balancing kit will be sent to you at no charge.

Specifications

• Item/Model Number: 88826WTNAB / 88826BKGLD / 88826SN

• Name: DAISY 60 5-BLADE FAN w LED LIGHT KIT

• Lamping | Ampoule: 1 x PCB In Tergared LED 12W

• General: 120V, 16758&7, 216

FAQ

Q: Can I use a different light kit with this fan?

A: Light kits must be UL-listed and suitable for use with this specific fan model. Refer to the instructions provided with the light kit for proper assembly.

Q: What is the recommended clearance for mounting this fan?

A: The fan must be mounted with a minimum of 7 ft. (2m) clearance from the trailing edge of the blades to the floor for safe operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>