WENTELMICRO ELECTRONIC A10 Wireless Guitar System Instruction Manual

WENTELMICRO ELECTRONIC A10 Wireless Guitar System

Product Information

Specifications

• Product Name: A10 Wireless Guitar Transmitter & Receiver
• Case: ABS Environmentally Friendly Material
• Plug: Gold Plated Copper
• Colour: Black with Painted
• Frequency Band: 2.4GHz
• Dynamic Range: 108dB
• Audio Resolution: 24 bit / 48KHz
• Frequency Response: 20Hz~20KHz, +1dB/-3dB

Product Usage Instructions

Operation Panel Overview
The operation panel consists of various buttons and indicators for easy control and monitoring of the A10 Wireless Guitar System.

Power On/Off and Pairing
To power on/off the system, push down the power button. Press and hold the transmitter until the indicator light flashes to witch between acoustic and electric guitar modes. The pair button  is used to switch between modes.

Charging and Volume Adjustment
Use a 5V Type-C cable to charge the system. The charging indicator will show a red light when charging, and turn off when the battery is full. Adjust the volume using the volume button on the transmitter or receiver.

Connection and Pairing
Connect sound sources with 6.35mm or 3.5mm interfaces to the transmitter and receiver. The indicators will show different lights based on pairing status and battery level.

Steps for Usage

1. Push down the power button to switch on the system.
2. Press both pair buttons to pair the transmitter and receiver.
3. Select mode: Acoustic guitar (green light) or Electric guitar (blue light).
4. Plug in the transmitter and receiver before turning on the amplifier.

FAQ

• Q: How do I know if the battery is low?
  A: The indicators will show specific light patterns based on the battery level. For example, low battery in acoustic mode is indicated by a flashing green light.

• Q: Can I adjust the volume levels on both the transmitter and receiver?
  A: Yes, you can adjust the volume using the volume buttons on either the transmitter or receiver. There are 4 volume levels in total.

Dear Valued Customer,
Hello! Thank you for buying our A10 wireless guitar transmitter and receiver. I hope you will have good shopping experience with us!

OVERVIEW

transmitter indicator light flashes to switch acoustic and electric guitar modes.
3| USB Charge Port| Use a 5V Type-C cable to charge. Both indicators show red light when charging. Battery full: light off.
4| Transmitter Plug (1/4″ & 1/8″)| #1 For connecting sound sources with 6.35mm interface. For example: guitar, bass and other musical instruments. #2 For connecting sound sources with 3.5mm interface. For example: phone, tablet and other devices.
5| Receiver Plug (1/4″ & 1/8″)| Used to connect amplifiers, speakers, audios, etc. with 6.35mm or 3.5mm interface.
6| Transmitter Indicator| Blue light flashes slowly when not paired. Blue light is always on when paired. Blue light flashes when the battery is low.
7| Receiver Indicator (2 Modes)| Blue and green light flash alternately when not paired. The green light is always on when paired for acoustic guitar mode. The blue light is always on when paired for electric guitar mode. Low battery: Acoustic mode – green light flashes; Electric mode – blue light flashes.
8| Charging Indicator| Charging shows red light. Battery full: light off.
9| Volume Button| You can adjust the “+-” volume button on the transmitter or receiver. There are 4 volume levels in total. The volume button are rotary and only adjust the volume up. Or you can try turning up the volume on your guitar and amplifier.

Packing List

• 1x Transmitter
• 1x Receiver
• 2x 6.35mm Plugs
• 1x Dual-ended Type-C Cable
• 1x Instruction Manual
• 1x Package Box

Steps for Usage

• Step 1: Push down to switch on the power.

• Step 2: Press both pair button and paired.
  ( Tips: The transmitter and receiver will be paired automatically when they are powered on. We have paired them before leaving the factory.)

• Step 3: Select mode: Acoustic guitar – Receiver shows green light. Electric guitar – Receiver shows blue light.

• Step 4: Plug in the transmitter and receiver first, and then turn on the amplifier to avoid unwanted noise caused by metal friction during insertion.

PLEASE PAY ATTENTION BEFORE USE

• First thing you should do after receiving the product is to fully charge it. It not only protects the product chip and battery, but also ensures the best first use effect.
• Pair the transmitter and receiver first before plugging them into your devices. If there is a problem with pairing, turn off the power and restart it.
• Green light showing on the receiver works in acoustic guitar mode, and blue light works in electric guitar mode. If blue light works in acoustic guitar mode, it might cause noise. But electric guitar works well in both of the mode. By selecting the appropriate mode, you can avoid problems.
• When using wireless transceivers, try not to use other devices with wireless interference. Wireless transmission only transmits the sound and can not change or amplifies the sound.
• Please lower the reverb of the guitar and amplifier, otherwise it affects the sound sensation.
• Please do not use it beyond 100 feet.
• Wireless transmission can not go through the wall, so please do not use it through the wall.
• After 4-5 hours of continuous use, please connect the charger for next use.
• Please use a 5V charger to charge it, otherwise the chip will be damaged.
• When the battery is about to run out, it may not work properly such as transmission problems.
• Busy bands can prepare more than 2 sets of wireless guitar system for uninterrupted band performances!

Product Specifications

( Tips: Manual measurement, there may be deviations.)

After-Sales

• If the product cannot be used, please apply for a replacement or full refund. And we will take care of it ASAP. The customer is always #1 for us.
• If you have any questions, please feel free to talk to us and give us feedback. This way we can make every effort to understand your issue. Thank you for your support.
  May your work go well and all your family be happy!

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in porlable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>