MINDEN S910 Remote Control Truck User Manual

MINDEN S910 Remote Control Truck

FAQ

Frequently Asked Questions

• Q: What should I do if the indicator lights do not behave as described?
  • A: If you encounter any issues with the indicator lights, please refer to the troubleshooting section in the user manual or contact customer support for assistance.
• Q: How long does it take to fully charge the remote control vehicle?
  • A: The charging time may vary depending on the battery capacity and version of the remote control vehicle. It is recommended to refer to the user manual for specific charging times.

14+ FOR AGES

Safety Information

Warning

1. Small parts. Please keep it out of reach of children.
2. Please operate in an open field without wave interference.
3. When the power of the transmitter is insufficient, please stop immediately and replace the battery.
4. When exiting after disassembly, please do not place discarded objects to avoid polluting hygiene.
5. Please store the car and transmitter in a dry and cool environment.
6. Keep away from fire source, high temperature or humid environment.
7. If the car battery is damp, please dry it thoroughly to avoid damage.

Product Configuration

Battery Instructions

Install transmitter batteries

1. Remove the battery cover at the bottom of the transmitter (Figure 1)
2. Install 3*1.5V AA battery according to correct polarity (excluding) (Figure 2)
3. Close the battery cover (Figure 3)

Attention

1. When installing the battery, be sure to match the polarity marked on the battery holder.
2. Do not mix old and new batteries.
3. Do not mix different types of batteries.

Charging and installing the rechargeable battery pack

1. Connect the battery interface of the remote control vehicle with the charging cable, then plug the USB charging cable into the USB interface of the computer or the USB charger, and then turn on the power supply.
2. USB Charge Status:
   • Standard version of two-color indicator light: the power supply red light is on and the green light is off; The charging green light is flashing and the red light is on; Full of green lights on and red lights off.

Remote control instructions

• A. Power Switches
• B. Steering trim
• C. Throttle trim
  • (low speed to high speed)
• D. Rudder fine adjustment

1. Forward
2. Braking
3. Left
4. Right
5. Backward
6. Light switch
   • (bruhless not supporter)

Brushed version:

• Green indicator light: The green light stays on when the remote control point source is turned on. Red indicator light: The red light flashes after power on, and goes off when paired with the vehicle; the red light stays on when the headlight switch is turned on.
• When the remote control battery is low, it flashes a warning.

Brushless version:

• Indicator light introduction: When you turn on the power of the remote control, the green light flashes. After the remote control is paired with the vehicle, the red and green lights stay on. When the remote control battery is low, the red light flashes to remind you.

Remote Control Switch Description

Power Switches

1. After connecting the battery interface with the power interface of the vehicle body, turn on the power key of the remote controller; The vehicle can be used after automatic frequency matching with the remote controller.
2. After connecting the battery with the power interface of the car body and electrifying it,it can be used after turning on the remote controller to automatically check the frequency successfully. (There is no power switch on the car body) Automatic low-power power-off protection when the battery is low (to prevent the battery trom being damaged due to overdischarge of the battery; When there is no control for more than 10 minutes after frequency matching, the remote controller and the power supply on the vehicle are automatically turned off to protect the power from being used for a long time.

Press and hold the power button for 3 seconds

After connecting the battery interface with the vehicle power interface; press and hold the speed control power light for 3 seconds to turn on the power; press and hold the remote control power switch for 3 seconds (the remote control power light flashes green); after frequency pairing with the remote control, the remote control indicator light (green) remains on.

Orientation fine-tuning

• When the chassis switch is on and the front tire is uneven, use ST.TRIM to adjust the position.
• ST.TRIM should be adjusted when the car turns excessively to the right.
• When the car overturns to the left, adjust ST.TRIM clockwise.

High and low speed adjustment

Suggestion

• Adjust TH. TRIM to low speed mode when playing for the first time; Familiar with control

Warning

1. Always turn on your transmitter before turning on the receiver in the vehicle.
   • Always turn the receiver off before turning off the vour transmitter.
2. Always drive your vehicle in an open area. Driving on slippery floors or indoors may cause crashes due to high speed.
3. Warning: S909.5910. Waterproof function, please note that the water level should be lower than the bottom of the truck. If excessive water enters the truck body and causes damage or other related problems, we will not be responsible for such damage. If necessary, the customer will be responsible for any replacement and additional accessories.
4. Always start at a low speed, otherwise the vehicle may skid or drive on corners. (Figure 1) Never operate your vehicle at top speed. Operating the vehicle at top speed can hurt yourself and damage your vehicle.

Motor Care

• For the first time, please drive safely on flat ground to greatly improve motor performance and prolong service life.
• Prevent overheating and prolong the life of motor. Frequent turning, stopping and starting, impact, driving in deep water and grass, and continuous uphill will all cause excessive wear and tear of the motor.

Troubleshooting

The instruction package contains important information, please keep it.

Disposal

CE Compiliance for Users in the European Union WEEE Compliance:

Please help the environment by disposing of your product responsibly at the end of its life. The wheeled bin symbol indicates that this product should not be disposed of in your household waste containers. Instead, the product should be disposed of by using a designated collection point for the recycling of waste electrical and electronic equipment, The Waste of Electrical and Electronic Equipment(WEEE) Directive (2002/96/EC) requires that the best available recycling techniques be employed to minimize the impact on the environment. Recycling electronics helps by keeping harmful chemicals out of the environment, and also saves money by reusing precious metals. Remove any batteries and dispose of them and the product at your local authority’s recycling facility. For more information about where you can drop off your waste equipment for recycling, please contact your local city ofice, your household waste disposal service or the location where you purchased this product.

Declaration of Conformity for RED Directive In accordance with IEC 17050-1

• This is to verify that the following products the requirements of the RED Directive AIK5Q/El and that all essential test suites have been carried out.
• The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

FCC STATEMENT

FCC PART 15 B Notice

CAUTION:

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that inteference will not occur in a particular installation. IF this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or experienced radio/TV technician for help.
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful inteference.
2. this device must accept any interference received, including interference that may cause undesired operation.

More Accessories And Parts

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>