STRONG SM-CEILING-CT-2×2-WH Suspended Ceiling Tile Replacement Installation Guide

: June 18, 2024
: STRONG

Table of Contents

Parts included
Installation instructions
Documents / Resources

SM-CEILING-CT-2×2-WH Suspended
Ceiling Tile Replacement
Installation Guide SM-CEILING-CT-2×2-WH
Strong™ 2×2 Suspended
Ceiling Tile Replacement **(White)**

Parts included

Warnings

Installation by a qualiﬁed professional is highly recommended.
Do not begin installation until these instructions have been thoroughly read and understood.
This ceiling plate supports a maximum load of 100 lbs (45.36 kg).
The manufacturer does not accept responsibility for incorrect installation.

Tools required

Power Drill
Screwdriver, Philips head
5/32” (4mm) Drill bit
13/32” Socket Head Wrench

Installation instructions

Step 1: Install the ﬂush mount tube
a. From the top, thread the Flush Mount Tube through Retaining Collar in Ceiling Tray (Fig 1). Step 2: Install the ceiling and ﬁller trays
a. Place Ceiling Tray into 24” (610 mm) x 24” (610 mm) opening in ceiling (in place of a ceiling tile) with Retaining Collar to the right or left.
b. Place Filler Tray into gap.
c. Attach Ceiling Tray to Filler Tray using four Screws and four Nuts (Fig 2).

Step 3: Install the wire supports
a. Insert Turnbuckle hooks into four corners of Ceiling Tray (Fig 3).
b. Pass the support wire through one end of the cable securing clamp, but do not secure it yet.
c. Pass the support wire through the turnbuckle hook eyebolt and loop back through the cable securing clamp (Fig 4a). At least 2″ (50.8mm) of non-load- bearing cable must extend from the clamp as shown by locator 1 in Fig 4b. Secure the clamp tightly using at least 1 N•m (8.85 in-lb) of torque (Fig 4b). d. Depending on mounting surface, perform the appropriate procedure below.

Wood Joists or Beams:
Drill 5/32” (4 mm) diameter holes 2” (51 mm) deep.
Fully insert the eye bolts (Fig 5).
After installing the anchors, pass the remaining support wire through one end of the cable clamp and loop the upper end through the anchor’s eye. Pull the support wire tight and secure it using the cable clamp. Tighten the clamp using at least 1 N•m (8.85 in-lb) of torque. Truss Ceiling:
No anchor required. After attaching the support wire to the turnbuckle, pass the remaining support wire through one end of the cable clamp and loop the upper end around the ceiling truss. Pull the support wire tight and secure it using the cable clamp (Fig 6). Tighten the clamp using at least 1 N•m (8.85 in-lb) of torque.

Position the holes so when the support wires are attached and taut, the optimal angle is 15°. Unit may be mounted at an angle up to 45° if necessary.
Caution: Do not extend two wires together – use one continuous wire.
Step 4: Install extension pole (optional)
a. If installed, remove the Flush Mount Tube.
b. From the bottom up, thread Extension Column (not included) up through
Retaining Collar in Adjustable Collar Mount Plate.
Fasten with a Set Screw using the Hex Wrench (Fig 7).

Warranty and Legal Notices
Find details of the product’s Limited Warranty at snapone.com/legal/ or request a paper copy from Customer Service at 866.424.4489. Find other legal resources, such as regulatory notices and patent and safety information, at snapone.com/legal/ .
Copyright ©2023, Snap One, LLC. All rights reserved. Snap One its respective logos are registered trademarks or trademarks of Snap One, LLC (formerly known as Wire path Home Systems, LLC), in the United States and/or other countries. Strong is also a registered trademark or trademark of Snap One, LLC. Other names and brands may be claimed as the property of their respective owners. Snap One makes no claim that the information contained herein covers all installation scenarios and contingencies, or product use risks. Information within this specification subject to change without notice. All specifications subject to change without notice.

Version 230926
Part # 200-SM-CEILING-CT-2X2-WH-A

Documents / Resources

| STRONG SM-CEILING-CT-2x2-WH Suspended Ceiling Tile Replacement [pdf] Installation Guide
SM-CEILING-CT-2x2-WH Suspended Ceiling Tile Replacement, SM-CEILING-CT-2x2-WH, Suspended Ceiling Tile Replacement, Ceiling Tile Replacement, Tile Replacement, Replacement
---|---