ideal lux Carta PL1 D40 Wall and Ceiling Lamp Instruction Manual

: June 11, 2024
: ideal lux

Table of Contents

ideal lux Carta PL1 D40 Wall and Ceiling Lamp
Wall and ceiling lamp
ASSEMBLY
SAFETY INSTRUCTIONS
Product Specifications:
FAQ (Frequently Asked Questions):
- Q: Can I replace the LED light source?
- Q: What should I do if the lamp does not turn on?
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ideal lux Carta PL1 D40 Wall and Ceiling Lamp

INSTRUCTION MANUAL

Wall and ceiling lamp

max 1 x 25W E27 / 220~240V 50/60Hz
– 8021696317120 BIANCO

ASSEMBLY

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION

THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.

SAFETY INSTRUCTIONS

1. This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
5. Always isolate power before commencing installation, maintenance or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors.
10. Luminaires not suitable for recessed on normally flammable surfaces.
11. Luminaire not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing to the ceiling.
13. This fitting is only suitable for fixing to the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
15. Only use lamps which do not exceed the maximum specified wattage.

16.’Jways observe the minimum distance between the lamp and the surface being llt, as shown in the icon. The lamp can cause a fire ff the minimum distance Is not observed.
17, Auto -protected bulb. Only use bulbs mar1<ed with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
18. Cracked or broken s afet y glass has t o be replaced Immediately. Use only manufctu rer approved parts complying with regulations.
19. Light source wit h n o t -substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not Immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20, This fitting is equipped with a fuse. H the lamp Is out of order, replace the Intern al fuse.
21. Class I Electrical safety g uaranteed b y the maln insulation and an additional protective conductor (earthing) connected with the metal frame of the la mp. Earthing Is obligatory.
22. Class II Electrical safety guaranteed b y the maln Insulat ion and a double or reinforced Insulation.
Earthing not necessary.
23. Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
24. Not protected.
26. Protected against solid objects greater than 50 mm.
26. Protected against s olid objects greater than 12 mm.
27. Protected against s olid objects greater than 2,5 mm.
28. Protected against solid objects greater than 1 mm.
29. Dust protected.
30. Totally protected against dust Infiltration.
31. Not protected.
32. Protected against vertically failing water drops.
33. Protected against water drops failing wi th a maximum angle of 15° to the vertical a xis.
34. Protected against rai n.
36. Protected against s plashing water.
36. Protected against water jets.
3 7 . Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged Immersion.
40. Lumlnalre not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source .