JBLGO4D Bluetooth Speakers User Guide
- June 10, 2024
- JBL
Table of Contents
JBLGO4D Bluetooth Speakers
Specifications
- Transducer: 45 mm / 1.75″
- Output Power: 4.2 W RMS
- Frequency Response: 110 Hz – 20 kHz
- Signal-to-Noise Ratio: > 85 dB
- Battery Type: Li-ion polymer 3.23 Wh (equivalent to 3.8 V / 850 mAh)
- Battery Charge Time: 3 hours (5 V 1 A)
- Music Play Time: Up to 7 hours (dependent on volume level and audio content)
- Bluetooth Version: A2DP V1.4, AVRCP V1.6
- Bluetooth Frequency Range: 2400 MHz – 2483.5 MHz
- Bluetooth Power: 9 dBm (EIRP)
- Product Dimensions (W x H x D): 94.3 x 75.7 x 42.2 mm / 3.7 x 3.0 x 1.7″
- Net Weight: 0.192 kg / 0.42 lbs
- Packaging Dimensions (W x H x D): 125 x 103 x 56.5 mm / 4.9 x 4.0 x 2.2″
- Gross Weight: 0.317 kg / 0.69 lbs
Product Usage Instructions
Bluetooth Pairing
To pair your device with the JBL Go speaker:
- Turn on the speaker by pressing the power button.
- Enable Bluetooth on your device and search for available devices.
- Select “JBL Go” from the list of available devices to pair.
Charging
To charge the speaker:
- Connect the provided charging cable to the speaker.
- Plug the other end into a power source with the specified requirements.
- The charging indicator will show when the battery is fully charged.
Multi-Speaker Connection
You can connect multiple JBL Go speakers for a synchronized audio
experience by using the JBL PORTABLE app for speaker configuration.
Frequently Asked Questions (FAQ)
-
Q: How long does it take to fully charge the speaker?
A: The speaker takes approximately 3 hours to fully charge with a 5V/1A power source. -
Q: What is the Bluetooth range of the JBL Go speaker?
A: The Bluetooth range is up to [insert range here] feet, depending on obstacles and interference.
QUICK START GUIDE
WHAT’S IN THE BOX
BLUETOOTH PAIRING
PLAY
MULTI-SPEAKER CONNECTION
APP
CHARGING
WATERPROOF DUSTPROOF IP
TECH SPEC
- Transducer: 45 mm /1.75″
- Output power: 4.2 W RMS
- Frequency response: 110 Hz – 20 kHz
- Signal-to-noise ratio: > 85 dB
- Battery type: Li-ion polymer 3.23 Wh (equivalent to 3.8 V / 850 mAh)
- Battery charge time: 3 hours (5 V 1 A)
- Music play time: up to 7 hours (dependent on volume level and audio content)
- Bluetooth® version: 5.3
- Bluetooth® profile: A2DP V1.4, AVRCP V1.6
- Bluetooth® transmitter frequency range: 2400 MHz – 2483.5 MHz
- Bluetooth® transmitter power: ≤ 9 dBm (EIRP)
- Bluetooth® transmitter modulation: GFSK, π/4 DQPSK, 8DPSK
- Product dimensions (W x H x D): 94.3 x 75.7 x 42.2 mm / 3.7 x 3.0 x 1.7″
- Net weight: 0.192 kg / 0.42 lbs
- Packaging dimensions (W x H x D): 125 x 103 x 56.5 mm / 4.9 x 4.0 x 2.2″
- Gross weight: 0.317 kg / 0.69 lbs
- Maximum operation temperature: 45 °C
To protect battery lifespan, fully charge at least once every 3 months.
- Battery life will vary due to usage patterns and environmental conditions.
- Do not expose the JBL Go 4 to liquids without removing cable connection. Do not expose JBL Go 4 to water while charging. It may result in permanent damage to the speaker or power source.
- Chemicals, salt or “foreign particles” in your pool or the ocean can damage the waterproof seals or harm the connector surface over time if not rinsed off after use. After a liquid spill or rinse, do not charge your speaker until it’s completely dry and clean. Charging when wet might damage your speaker.
- When using an external adapter, the output voltage/ current of the external adapter should not exceed 5V/3A.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>