Shark GI435 Series Iron User Manual

Shark GI435 Series Iron User Manual

OWNER’S GUIDE
GI435 55

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING YOUR IRON

When using your iron, basic safety precautions should always be followed, including the following:

1. Use iron only for its intended use.
2. To protect against risk of electrical shock, do not immerse the iron in water or other liquids.
3. DO NOT yank cord to disconnect from outlet. Grasp plug and pull to disconnect.
4. DO NOT allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing.
5. Always disconnect iron from electrical outlet when filling with water, emptying, or when not in use.
6. DO NOT operate iron with a damaged cord, or after the iron has been dropped or damaged in any manner. To avoid the risk of electric shock, do not disassemble the iron. Return to EURO-PRO Operating LLC for examination, repair or adjustment. Incorrect reassembly can cause the risk of electric shock when the iron is used.
7. Close supervision is necessary for any appliance being used by or near children. DO NOT leave iron unattended while connected or on an ironing board.
8. Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down; there may be hot water in the reservoir.
9. Never use or rest iron on an unstable surface.
10. While the iron is hot, never set iron on an unprotected surface – even if it is on its heel rest.
11. Always store your iron standing upright, not on the soleplate. If stored face down, even the smallest amount of moisture will cause the soleplate to corrode and stain.
12. This appliance is for household use only.

CAUTION! TO PREVENT ELECTRIC SHOCK OR OTHER INJURY, before filling the iron with water, make sure that the plug is removed from the outlet.

WARNING: Never fill the iron with fabric conditioner, starches or any other solution, as these will damage the steam mechanism. Do not use contaminated water.

CAUTION! TO AVOID FIRE, never leave iron unattended while it is plugged in.

CAUTION! TO PREVENT ELECTRIC SHOCK, never use the iron in a location where it can fall or be pulled into water or another liquid. If the iron falls into water or other liquid, unplug it immediately. DO NOT reach into the water or liquid.

WARNING: Never use scouring pads, abrasive or chemical cleaners, or solvents to clean the exterior or soleplate of your iron. Doing so will scratch and/or damage the surface.

CAUTION! DO NOT aim iron at face, towards yourself, or anyone else while using or adjusting steam. Burns or serious injury may occur.

SPECIAL INSTRUCTIONS

1. To avoid a circuit overload, do not operate another high-wattage appliance on the same circuit.
2. If an extension cord is absolutely necessary, use a 15-ampere cord. Cords rated for less amperage may overheat. Use care to arrange the cord so that it cannot be pulled or tripped over.

“SAVE THESE INSTRUCTIONS”

FEATURES

Filter (not shown)
8. Water Level Window|

TECHNICAL SPECIFICATIONS: 120 Volts, 60 Hz., 1600 Watts

This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

BEFORE FIRST TIME USE

1. Before using your iron for the first time, please remove all the packaging material.
2. When you turn on the iron for the first time it might emit an odor for the first ten minutes. This is because the materials used in making the iron are heating up. The odor is safe and should not re-occur after the initial heating.

USING YOUR IRON

3. Fill water carefully into the water tank without going over “Max” line. Make sure the water inlet cover is closed to avoid spilling.
4. Plug in the iron into any 120V AC polarized electrical outlet.
5. Set the desired fabric/temperature by pressing the Electronic Temperature Control.

6. The temperature indicator light on the LED Display Panel will flash when
the iron is heating up. The green light will stop flashing and stay on when the iron reaches the preset temperature.
7. Turn the variable steam control to select high or low steam setting. Select “0” on the steam control for dry ironing. You can now start ironing.
8. Use the steam burst/X-tended steam burst button to remove stubborn wrinkles. Turn the button counter-clockwise to the burst of steam position (for quick bursts of steam); or turn the button clockwise to the X-tended steam burst position (for prolonged bursts of steam). Press the button in the steam burst position once or several times if in the X-tended steam burst position to prime the pump. Allow an interval of 3 seconds between each burst. Overuse of the steam burst may cause water spitting or weak steam performance.
9. The steam burst feature also works in the vertical position. This is especially useful to remove wrinkles from hanging clothes, delicate garments and other fabrics. Hold the iron in the upright position several inches away from the article.
10. Use the atomizer spray to moisten the fabric to tackle tough wrinkles, if necessary.

ANTI-DRIP FEATURE

11. The anti-drip feature is built in to this iron. It prevents water spitting when the temperature is too low.
12. Steam cannot be produced if the soleplate is not hot enough. It may result in water spitting or leaking from the soleplate. The anti-drip feature reduces water dripping and leaking when ironing at low temperatures.

ANTI-CALCIUM

13. This iron has built in the anti-calcium system that prolongs the life of the iron.
14. If you have very hard water, we recommend using distilled water instead of tap water.

ELECTRONIC MULTI POSITION AUTO-OFF

15. This iron is equipped with an electronic auto-off feature that switches the iron off if it has been idle in the sideways, flat or upright positions for 7-9 minutes.
16. The auto-off light will flash in red on the LED display when the iron is in auto-off mode. To turn the iron back on, just gently rock the iron back and forth several times until the “Power ON” green light is re-illuminated. Reset the temperature to the desired setting; wait for the green light to stop flashing. The iron might have to warm up for a minute if the auto-off feature was activated for an extended time.

SELF-CLEANING

17. Fill the water tank to the “MAX” level. Do not overfill.
18. Stand the iron on its heel, standing up on a protected surface and plug into the electrical outlet
19. Set the Electronic Temperature Controls to “•••” setting. Wait until the green light stops flashing. The iron is now on the preset temperature.
20. Hold the iron horizontally over the sink. Turn and hold the steam control all the way to the right to the SELF CLEAN position.
21. Move the iron back and forth. Boiling water and steam will now be ejected from the holes in the soleplate. Use caution when doing this as the water and the steam are hot enough to cause burns.
22. Continue step 21 until the impurities and scale are washed away.
23. Empty any excess water from the tank. Don’t touch the hot surfaces, water or steam because injury may occur.
24. Turn the steam control to “0”.
25. Place the iron in upright position and let it cool down.

USEFUL TIPS

26. Read all garment care labels before you start ironing. You can also test the temperature of the iron on a hem or an inside seam.
27. Iron similar fabrics together and in sequence of synthetic fibers acrylic, nylon, silk/wool, polyester, and cotton/linen. This will reduce the need to adjust the temperature frequently.

IRONING GUIDE

STORAGE AND CARE

28. Always turn the variable steam control to “0” after you have emptied the water tank.
29. Allow the iron to cool down before putting it away.
30. Place the iron in the upright position during heating up, cooling down and storage.
31. Avoid any sharp material contacting the soleplate.
32. Every two weeks, clean the exterior of the iron with a damp cloth and wipe dry.
33. If you use spray starch, wipe the soleplate occasionally with a soft, damp cloth to prevent deposit build-up.
34. If the iron hasn’t been used in a few weeks, hold the iron horizontally and allow steaming for 2 minutes before ironing.

ALWAYS REMEMBER

36. Unplug the iron from the electrical outlet before pouring water into the iron.
37. Always empty the water in the iron after each use.
38. Never iron or steam clothes while they are being worn.
39. Be very careful when filling the iron with water. Injuries may occur if the hot metal parts, hot water or steam are contacted.

TROUBLE SHOOTING

outlet only.
Make sure the plug is securely in the socket.
Temperature setting might be too low.
Try turning to a higher setting.
Auto-off feature is activated.
An odor is being emitted from the new iron or small particles are coming out| This is normal.
Follow the instructions for first-time use and allow iron to steam through 2-3 fillings and press the steam burst button occasionally to eliminate small white particles.
Iron doesn’t steam| Water tank may be empty or water level is very low. Add water.
Make sure the fabric/temperature setting and the variable steam control are correctly set. For maximum steam, set “MAX” on steam control and the temperature setting should be set on “•••.”
Steam control is set on “0.”
The soleplate is not hot enough and the anti-drip feature switches off the steam. Always allow the iron to reach the selected temperature with the variable steam control setting at “0.” For more steam, turn temperature dial to a higher setting and the steam control to “MAX.”
If the temperature setting and steam control settings are correct and there is no steam, gently move the iron left or right a couple of times. Move the Steam Control from “0” to “MAX” a few times.
Water droplets coming from steam vents| Variable Steam Control lever may be set in “self clean” position. Align the lever to the “0” to “Max” steam setting.
Iron may not be hot enough. Set temperature to “•••” position. Always allow iron sufficient time to heat up before activating the variable steam control.
Overuse the steam burst. Allow more time between each burst.

ONE YEAR LIMITED WARRANTY

EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of one (1) year from the date of purchase when utilized for normal household use, subject to the following conditions, exclusions and exceptions.

The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC.

If your appliance fails to operate properly while in use under normal household conditions within the warranty period, you may return the complete appliance and accessories with proof of purchase and date, freight prepaid. For customer service support, call 1-800-798-7398 or visit our website at www.sharkclean.com.

If the appliance is found by EURO-PRO Operating LLC to be defective, in EURO- PRO Operating LLC’s sole discretion, we will repair or replace it free of charge. Proof of purchase date and check made payable to EURO-PRO Operating LLC in the amount of $9.95 to cover the cost of return shipping and handling must be included.

This warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific obligations expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages to anyone of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach a tag to item before packing including your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with the item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>