Shenzhen SYD Network Technology Co Ltd 3600PRO Portable Power Station User Manual
- June 9, 2024
- Shenzhen SYD Network Technology Co Ltd
Table of Contents
- Shenzhen SYD Network Technology Co Ltd 3600PRO Portable Power Station
- Precautions For Use
- AC Output Parameter
- Packing list
- Product Introduction
- Button Function Introduction
- Introduction of Display Interface
- Troubleshooting
- UPS Mode
- Battery Pack Connection Instructions
- Product Specifications
- Warranty
- FCC STATEMENT
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Shenzhen SYD Network Technology Co Ltd 3600PRO Portable Power Station
Hi dear, thank you very much for purchasing and experiencing the 3600W
portable power station. Before operating this product, please carefully read
the user manual for proper operation.
According to the transportation requirements of the international customs for
battery products, the battery level of this product is only less than 30% when
it leaves the factory. Please fully charge the product after unpacking it to
start the experience tour of 3600W.
Precautions For Use
-
Please avoid long-term storage and use of this product in environments with high temperatures and humidity or direct sunlight to avoid shortened battery life and other failures. The product should not be close to the fire source, otherwise it may cause a major fire or accident.
-
This product must not be disassembled or modified. Improper operation may cause product malfunction or even fire.
-
Be careful not to drop the product.
-
Please store or use this product out of the reach of children, otherwise, the product may be dropped or collided and may cause bodily injury to children.
-
Please use our original accessories, and we will not guarantee the defective products caused by the use of non-original accessories.
-
Please directly plug in the wall socket to charge the product, do not use extension cords or cable taps, otherwise there is a risk of damage to the extension cords and cable taps or even a fire; If the extension socket is plugged in to charge this product, please do not connect other electrical appliances to this socket, otherwise the household meter may trip.
When the product is not in use or idle, please turn it off and unplug the power cable. If it needs to be idle for a long time, please consume the product from a fully charged state to an uncharged state, then recharge it to about 50% of the battery level and store it. In order to prolong the life of the product, please take three months as a cycle, operate and keep it in this way. -
If the product reaches scrap conditions, please discard or recycle the product in accordance with local laws.
AC Output Parameter
Packing list
Product Introduction
This product is a portable power device with a built-in battery pack with a
charge/discharge function. It includes both AC output interface and output,
etc. It also has functions such as display, interface control, protection, and
alarm. Moreover, this product can be charged by mains AC, solar panels and
vehicle charging. It can be used with up to two battery packs with a maximum
capacity of 11520Wh.
The following are the main features of this product:
- Equipped with a LiFePO4 battery host, the battery energy is up to 3840Wh, and after merging, the maximum capacity can reach 11520Wh, which can meet the daily consumption of a family.
- Pure sine wave AC output can meet almost all daily electronic equipment and small household appliances.
- Two-way fast charging technology is adopted to fully charge the product within 3 hours.
- A great variety of output interfaces such as USB-A, Type-C PD3.0, DC 5521, XT60, cigarette lighter output, etc.,meet many different application scenarios.
- In UPS mode, the switchover time is less than 1 Oms which is truly seamless switching.
- Multiple protection mechanisms such as a battery, circuit, structure, etc., guarantee product safety.
Button Function Introduction
- Power ON/OFF Button
- USB ON/OFF Button
- LED Light Button
- DC ON/OFF Button
- LCD Screen
- Input Power Adjustment Button (J) Cooling Air Button
- AC Button(manually switch to 50/60Hz)
- XT90 Input Port
- AC Input
- Overhead Protection Button @ Parallel Port
CD Power ON/OFF Button
Instructions: Press and hold the power button for 3S to turn on/off the whole system.
USB ON/OFF Button
Instructions: Short-press the USB button to turn on the USB output Port and
short-press it again to turn it off.
Light Button
Instructions: Short press the LIGHT button, and the LED light is on; short
press it again, and the LED light enters the SOS mode, short press in
turn,enters the strobe mode, and finally the LED light is turned off (LED
light in any mode, long press the LIGHT button for 1 second, directly turn it
off).
DC ON/OFF Button
Instructions: Short-press the DC button to turn on the DC output port, and
short-press it again to turn it off.
LCD Screen
Display the product’s battery level and usage status tips.
Input Power Knob
When the product is connected to the AC mains for charging, the power is
adjusted according to the actual input voltage. The clockwise rotation
increases the input power, and the counterclockwise rotation decreases the
input power. It is worth noting that charging this product at low power is
beneficial for extending battery life.
Cooling Suction/Exhaust Port
When the product reaches the temperature threshold set by the system, the cooling fan will automatically run, accompanied by a certain fan noise (fan noise below 60dB is normal). Do not block the cooling suction/ exhaust port during use of this product, and do not place any object within the range of 30CM.
AC Button
Tap the AC button to enable the AC output function. Since there may be differences in the AC output frequency and voltage in different regions, if you need to switch the frequency and voltage, the operations are as follows:
- Press and hold the AC button for 3 seconds to enter the frequency switching mode, the 50Hz or 60Hz icon will flash on the display, short press the AC button again to select 50Hz or 60Hz; when the icon stops flashing and displays 50Hz or 60Hz, it indicates the switch is successful.
- Quickly press the AC button 10 times to select a voltage. Noted: USA cannot choose voltage.
XT90 Port (Solar Panel Input)
This interface supports solar panel input or car charger input. For details, please refer to “Solar Panel Connection” on page 10 of this manual and “CarNehicle Charging” on page 11.
AC Input
Charging the product by a household socket can achieve 1500W (100V-120V)/2200W
(220V-240V) fast charging.It only takes three hours to fully charge from Oto
100%. When charging in this way please pay attention to the following points:
- Please directly plug in the wall socket to charge the product, do not use extension cords or cable taps, otherwise there is a risk of damage to the extension cords and cable taps or even a fire.
- If the extension socket is plugged in to charge this product, please do not connect other electrical appliances to this socket, otherwise the household meter may trip.
Overload Protection Button
When the power supply voltage is unstable due to lightning or other reasons,
and there is a large voltage input at the AC Input, in order to protect the
product, the overload protection function (safety circuit breaker) will
activate and cut off the AC input port. Please follow the sequence below to
restore the AC input function:
- Turn off the power button and unplug all ports.
- After confirming that there is no abnormality in each part, turn on the power button.
- Press the overload protection button, and connect the AC Cable to restore the AC input.
Battery Pack Interface
The capacity expansion needs to be accomplished by connecting the parallel
cable to the portable power station. This interface can achieve a maximum
input and output of 4000W.
Introduction of Display Interface
- Remain Using/Recharging Time
- Host Logo
- Parellel Operation Logo
- lnput Power in Total
- Connected to the AC Mains
- XT90 Port
- High/Low Temperature Protection
- Fan Status
- UPS
- Battery Level Percentage
- Battery Progress Bar
- AC Output
- DC (12V) Output
- USB Output
- PD3.0 Output
- XT60 (12V) Output
- Cigar Lighter (12V) Output
- LED Light
- Output Power in Total
Screen Display Description
Power display: When the product is in the charging state, the battery progress
bar rotates continuously in the form of a clockwise marquee, and the battery
level percentage gradually increases; when the product battery level is 0, the
battery level percentage icon flashes.
- Input and output status: When the product is working, the total input power, total output power and the cursor corresponding to the working area will be displayed on the screen.
- Alarm prompt : See the following troubleshooting table for details.
Troubleshooting
Troubleshooting Sheet
UPS Mode
UPS Feature
This product has the function of backup uninterruptible power supply. The usage and operation precautions are as follows: As shown in Pic1 below, when the product is connected between the wall socket and the electrical appliance, and the power supply and AC switch of the product are in the ON state, the product enters the UPS working mode. The AC mains in the socket supplies power to the electrical appliance through the bypass circuit, and also charges the product.In this working state:
- The rated power of the electrical appliance must be lower than 1500W(only 100V~120V) otherwise overload protection may be triggered.
- The rated power of the electrical appliance must be lower than 2500W(only 220V~240V) otherwise overload protection may be triggered.
As shown in Pie 2 below, when the AC mains at the socket end is disconnected, the bypass output inside the product stops working, the product switches to a bidirectional inverter circuit within 1 Oms, and the circuit outputs supply power to the electrical appliance to ensure that the electrical appliance is uninterrupted and works normally during the process
Battery Pack Connection Instructions
The portable power station can be connected to up to two battery packs through
parallel cables, with a maximum capacity of up to 11520wh. Please connect the
product when the portable power station and extra battery pack are turned off.
After the connection is completed, there will be icons of S1 and S2 connection
displays on the screen. After connecting them successfully, the system can
start charging or discharging. When charging and discharging after connection,
the power will be distributed according to the left power of the product. The
charging power of the device with lower capacity is small when charging, and
the output power of the device with higher capacity is high when discharging.
If there is no external charging, Energy exchange may occur between the
portable power station and battery packs.When the left capacity of them is
close, the charging process will stop, and the power will be shown on the
screen.
Precautions
- Please do not plug and unplug the connecting cable when the products is under use, please connect or disconnect these two products when they are turned off.
- Please do not make the connecting ports of the portable power station short-circuited.
Connection of Solar Panels
Under the condition of light, this product can be connected to the solar panel
and getting charged. The charging power is determined according to the
conditions of light and weather. In this charging mode, we support solar panel
input within 2000W, and the input voltage cannot exceed 160V, otherwise the
product abnormality caused by it will not be covered by the warranty.
We recommend the following two charging schemes:
Solar panel charging
Scheme One
- Portable Power Station Charging Area.
- Scheme Two
Portable Power Station Charging Area.
CarNehicle Charging
When the car is in the process of starting, connect the car charging port on
the car and the product through the car charging cable to charge the product.
The connection method is shown in the picture below:
This product supports 12V/24V car charger charging, please pay attention to
the following two points when using this method to charge:
- Please do it when the car started, otherwise the car battery may be exhausted.
- Vehicle charging power is usually in the range of 90W-120W, and the charging time is long. If fast charging is required, the AC mains charging is recommended.
Product Specifications
Product Name | Portable Power Station |
---|---|
Dimension | LWH=550321 464mm |
Weight | 42Kg |
Capacity | 3840Wh(3*3840Wh MAX11520Wh) |
Parallel Capacity | 100V-120V 1500W max;220V-240V 2200W max |
XT90 Input | 12-160V 2000W max |
AC Output
| 100V rated 3300W;120V rated 3600w; 220V-240V, rated 3600W;pure sine wave
USB-A Output| (QC3.0 18W)2
Type-C(D Output| (PD20W)3
Type-CQ) Output| (PD100W)1 Included PD3.0 Protocol
DC 5521 Output| 12V/3A2
XT-60 Output| 12V/25A
Car Charging Output| 12V/10A
Shutdown Current| <500uA
Working Temperature| -10-40°C
Environment Humidity| :590%RH
Cycle Times| >4000 times
Batttry Specifications
Cell type | 40135 LiFePO4 |
---|---|
Rated voltage of single battery | 3.2V |
Rated capacity of sigle battery | 20Ah |
Rated voltage of battery pack | 48V |
Output voltage range of the battery pack | 40V-54V |
Rated capacity of battery pack | 3840Wh |
Warranty
Warranty Card
Name|
Address|
Tel|
Mail|
Brand, Order number|
Buying date|
Fill in the date|
What is the product failure
|
Please fill in all the above items.
This product provides a 24-month warranty service from the date of purchase
- If there is a quality problem within the range of normal use, we provide warranty service.
- After purchasing our company’s products, please keep this product together with invoices and other items. When maintenance services are needed, please provide information according to our company’s request.
- In the case where the warranty is damaged or altered,and no stamp of the sales store on the warranty, the warranty service may not be provided.
- Damage caused by use beyond the normal range of use is not covered by the warranty service.
- The content of the warranty scope shall be subject to the content recognized by the company.
- Even within the scope of the warranty, sometimes it will be exchanged for products with the same function. The shipping and repair fees for products outside the warranty range shall be paid by the customer.
- Sometimes the specifications and functions of the product will be updated without prior notice.
Disclaimer
Before use, please read the user manual of this product to ensure full
understanding and correct use. After reading, keep the user manual properly
for future reference. If you do not operate this product correctly, you could
cause serious injury to yourself or others, or result in damage to the product
and property. Once you use this product, you are deemed to have understood,
recognized and accepted all terms and content of this document. Users
undertake to be responsible for their own actions and all consequences arising
therefrom. We are not responsible for all losses caused by the user’s failure
to use the product in accordance with the User Manual.
In compliance with the law, the company has the final right to interpret this
document and all related documents of the product. If it is updated, revised
or terminated without prior notice, please visit our official website for the
latest product information.
FCC STATEMENT
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &your body.