Ken-Tech T4660 Bathroom Digital Atomic Clock Instruction Manual
- June 8, 2024
- Ken-Tech
Table of Contents
Ken-Tech T4660 Bathroom Digital Atomic Clock
OVERVIEW
NOTE: Your new radio controlled atomic clock will automatically receive and set itself to the split second exact time broadcast by radio from the US National Time Observatory near Denver, Colorado. The time signal is broadcast at intervals, and as radio reception is better at night, it may take overnight for your clock to receive the signal.
- If the clock it too near to an interfering device, such as a TV set or computer, or if it is in a shielded or difficult reception area, it can make it harder to get the radio time signal.
- Your radio controlled atomic clock is equipped with a large, pliable suction cup for mounting on glass, tile, or any smooth surface. Turn the suction cup mount to unscrew it from the clock. You can moisten it for better adhesion. Locate it as desired in your bathroom. Press to stick, set the clock as in the instructions and screw the body of the clock back on. As you tighten, it draws the suction cup for better adhesion.
IMPORTANT: In the US, it is necessary to set the time zone (Pacific, Mountain, Central or Eastern). To set the time zone, press the MODE key to enter the alarm time mode. Then consecutive pressing of the SET key while observing the indicator on the map icon of the US in the upper right corner of the LCD display will let you set it for your proper zone.
- The clock automatically adjusts itself for daylight saving time (DST) when it goes into effect. If you live in one of the few areas that do not observe DST, you will have to manually reset the clock.
USER’S INSTRUCTIONS
Getting Started
- Remove the body of the clock from the suction cup mounting by holding the clock and spinning the suction cup.
- Unscrew the screws of the back cover and life the cover off.
- Insert one new “AA” battery as per indication marker in the battery compartment.
- Re-fix the battery door and secure its screws evenly.
- When the battery is inserted, all the segments of the display will be shown briefly before entering the radio controlled time reception mode.
- The RC Clock will automaticallv start scanning for the radio controlled time signal after 15 seconds.
NOTE: If no display appears on the LCD after inserting the battery, replace a new “AA” battery or press the reset button.
PRODUCT FUNCTIONS
Function Keys
- MODE Button: Switch between Normal Time Mode and Alarm Time Mode.
- SET Button: In normal time mode, toggle between 12 to 24 hour format. In setting mode, step the setting items.
- ADJUST Button: Toggle between Month/Date and Year display. In Alarm Time Mode, switch ALARM/SNOOZE function on or off. In setting mode, adjust the value of the flashing digit.
- RECEIVE Button: Press the RECEIVE button to receive the signal for reception testing. Check the signal strength indicator in the first 30 seconds. If the signal strength is in acceptable signal quality, leave the clock in its current location. Otherwise, move the clock to another location. The reception stops automatically after 6-12 minutes.
- SNOOZE Button: Stop the snooze function during its activation.
NOTE: Press SNOOZE button for 8 seconds to turn the current RC reception off. Press RECEIVE button to activate the RC function manually or let it search for the time signal automatically at 2:00am, 3:00am, 4:00am or 5:00am.
Time Setting
Select the Time Zone (For USA Only)
Make sure the time zone is already set to appropriate location. The default time zone is Pacific. If your location is out of Pacific zone, please do the following steps:
- In Normal Time Mode, press the MODE button to enter the alarm time mode.
- Press the SET button to change the time zone. P – Pacific, M – Mountain, C – Central, E – Eastern.
Signal Strength Indicator for Radio Controlled Time Setting
The signal indicator displays signal strength in 3 levels. Wave segment flashing means time signals are being received. If the indicator shows two incomplete waves, the signal quality is poor. One incomplete wave means this signal quality is acceptable. One complete wave means the signal quality is excellent. If the clock receives the signal successfully, a solid signal strength symbol appears on the display. After the time signal is received, the signal strength symbol will no longer appear.
NOTE: You may use the RECEIVE button to receive the time signal manually. The Receive Mode stops automatically after 6-12 minutes. The Receive Mode consumes more battery power and will reduce the battery lifetime.
About the Daylight Saving Time (DST)
- The clock has been programmed to automatically switch when daylight saving time is in effect. Your clock will show DST during the summer.
Manually Setting the Time and Date
If the clock does not receive the signal successfully you can set the clock manually.
- Press the SET button for 3 seconds until the HOUR digit flashes.
- Press the ADJUST button to increase the value of the flashing digit.
- Press the SET button again to step the setting items. The sequence is Hour → Minute → Second → Month → Date → Year → Day language.
- Press ADJUST button to increase the value of the flashing digit and select the Day language: GB (English), FR (French), DE (German), ES (Spanish), IT (Italian).
- Press the MODE button to exit the setting mode.
Setting the Alarm
- In the Normal Time Display Mode, press the MODE button to enter the Alarm Time Mode.
- Hold the SET button for 3 seconds until the HOUR digit flashes.
- Press the ADJUST button to increase the setting value.
- Press the SET button again to step the setting items. The sequence will be: Hour → Minute.
- Press the MODE button to exit the setting mode.
Using the Alarm and Snooze Function
- In the Normal Time Display Mode, press the MODE button to operate the alarm and snooze function.
- Activate the ALARM by pressing the ADJUST button so that the bell icon appears.
- Activate the Snooze by pressing the ADJUST key to that the snooze icon “Zz” appears.
- To deactivate the alarm and snooze function, press the ADJUST button until both icons disappear.
NOTE: To stop the alarm, press any button when the snooze function is activated. The alarm will automatically start again after 4 minutes, total 4 times then it will not sound again until the next day. The alarm duration is 60 seconds.
Important: For best reception performance, please read the following instruction.
- We strongly recommend you start your clock at night. Allow the clock to receive the signal automatically overnight.
- Place the unit away from interfering sources such as TV set, computers, microwaves, etc.
- Avoid placing the unit on or next to metal surfaces.
- Avoid closed areas such as airports, basements, cement office buildings, or factories.
- Do not start reception on a moving article such as a train or vehicle.
How to Fix the Clock on Smooth Surface
NOTE: When tightening the suction cup; DO NOT over tighten. As you screw the clock onto the suction cup, the grip of the suction cup improves. If you tighten it too much, the plastic screw will break. If the clock is not at the desired angle, unscrew the clock and rotate the suction cup. Try tightening it again until the proper angle is achieved.
The radio controlled atomic clock is equipped with a large pliable cupula for mounting on glass, tile or any smooth surface. In order to mount the clock with better adhesion, please do exactly as directed:
- Make sure the place you choose to mount the clock on is smooth and clean.
- Turn cupula to unscrew it from the clock, then fix the cupula slightly on the smooth surface.
- Put the bottom cover of the clock through the pole along with the cupula.
- Tightly screw the body of the clock on the pole along with the cupula.
- Rotate the clock by spinning out the body of the clock counterclockwise and slightly pulling the pliable tip on the cupula.
- Keeping vacuum in the space between cupula and smooth surface is required for good adhesion.
FREQUENTLY ASKED QUESTIONS
What are the key features of the Ken-Tech T4660 Bathroom Digital Atomic Clock?
The Ken-Tech T4660 Bathroom Digital Atomic Clock features a digital display, automatic watch movement, atomic operation mode, waterproof design, and radio function.
How does the atomic operation mode of the Ken-Tech T4660 Bathroom Digital Atomic Clock work?
The atomic operation mode ensures precise timekeeping by synchronizing the clock with atomic time signals broadcasted by atomic clocks, providing accurate timekeeping.
What is the special feature of the Ken-Tech T4660 Bathroom Digital Atomic Clock regarding its waterproof design?
The Ken-Tech T4660 Bathroom Digital Atomic Clock is designed to be waterproof, allowing it to withstand moisture and humidity commonly found in bathroom environments.
What is the power source for the Ken-Tech T4660 Bathroom Digital Atomic Clock?
The Ken-Tech T4660 Bathroom Digital Atomic Clock is powered by batteries, providing flexibility in placement without the need for a power outlet.
What is the product dimensions of the Ken-Tech T4660 Bathroom Digital Atomic Clock?
The Ken-Tech T4660 Bathroom Digital Atomic Clock measures 3.5 inches in width and 2 inches in height, providing a compact and space-saving design.
What is the item weight of the Ken-Tech T4660 Bathroom Digital Atomic Clock?
The Ken-Tech T4660 Bathroom Digital Atomic Clock weighs approximately 6.7 ounces, making it lightweight and easy to mount on bathroom walls or surfaces.
What type of display does the Ken-Tech T4660 Bathroom Digital Atomic Clock feature?
The Ken-Tech T4660 Bathroom Digital Atomic Clock features a digital display, providing clear and easy-to-read time information.
Who is the manufacturer of the Ken-Tech T4660 Bathroom Digital Atomic Clock?
The Ken-Tech T4660 Bathroom Digital Atomic Clock is manufactured by Sonnet, known for their quality timekeeping products.
Where can I purchase the Ken-Tech T4660 Bathroom Digital Atomic Clock and what is its price?
The Ken-Tech T4660 Bathroom Digital Atomic Clock is available for purchase from various retailers. The price is listed as $24.74, offering affordability along with its waterproof and atomic features.
What is the model number of the Ken-Tech T4660 Bathroom Digital Atomic Clock?
The model number of the Ken-Tech T4660 Bathroom Digital Atomic Clock is T4660, allowing for easy identification and reference when purchasing or troubleshooting.
What should I do if my Ken-Tech T4660 Bathroom Digital Atomic Clock is not displaying the correct time?
First, ensure that the clock is set to receive atomic time signals properly. Place the clock near a window or an outside wall where it can receive a strong radio signal. Then, allow the clock some time to synchronize with the atomic time. If the issue persists, try resetting the clock and repeating the synchronization process.
How can I troubleshoot if the alarm on my Ken-Tech T4660 Bathroom Digital Atomic Clock is not sounding?
Check if the alarm volume is set to an audible level. Also, ensure that the alarm is activated and that the correct alarm time is set. If the problem persists, try replacing the batteries with fresh ones and test the alarm again.
What should I do if the display on my Ken-Tech T4660 Bathroom Digital Atomic Clock is dim or not lighting up at all?
Firstly, check if the batteries are properly inserted and have sufficient power. If the display remains dim, try adjusting the brightness settings of the clock. Additionally, clean the display screen with a soft, dry cloth to remove any dirt or debris that may be obstructing the light.
How can I troubleshoot if my Ken-Tech T4660 Bathroom Digital Atomic Clock is not responding to button inputs?
Inspect the buttons for any physical damage or debris that may be hindering their operation. Gently press each button to ensure they are not stuck. If the issue persists, try resetting the clock by removing and reinserting the batteries.
How can I troubleshoot if the radio function of my Ken-Tech T4660 Bathroom Digital Atomic Clock is not working?
Ensure that the clock is placed in an area with good radio reception. Extend and adjust the antenna if applicable. If the radio function still doesn't work, try manually tuning to different radio stations to check for reception.
VIDEO – PRODUCT OVERVIEW
DOWNLOAD THE PDF LINK:Ken-Tech T4660 Bathroom Digital Atomic Clock Instruction Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>