PHILIPS INtelliVue MX40 Single Patient Use Cables Instruction Manual
- June 8, 2024
- Philips
Table of Contents
INtelliVue MX40 Single Patient Use Cables
Instruction Manual
INtelliVue MX40 Single Patient Use Cables
ECG Only
AAMI 5-lead grabber
989803172031
IEC 5-lead grabber
989803172131
ECG + SpO2
AAMI 5-lead grabber plus SpO2
989803172051
IEC 5-lead grabber plus SpO2
989803172151
About This Edition
Notice
Copyright © 2011
Koninklijke Philips Electronics N.V.
All rights are reserved.
Printing History
Current Edition/Revision:
Printed in Germany October 2011
Part Number 453564230191
Rx only United States law restricts this device to sale by or on the
order of a physician.
Product Overview
Intended Use
The Single-Patient-Use MX40 Patient Cables are intended to provide ambulatory
and bedside monitoring of ECG/Impedance Respiration, or ECG/Impedance
Respiration plus SpO2 parameters, for adults who weigh greater than 40kg and
pediatrics who weigh greater than 20kg. The cables are for use with IntelliVue
MX40 patient wearable monitors, and are intended to be used by trained
healthcare personnel in a professional healthcare facility.
Cable Configurations
The MX40 Single-Patient-Use Cables are available in ECG only or ECG/SpO2
configurations (see below).
| *5-Lead ECG Only** | 5-Lead ECG with attached SpO2 Sensor |
|---|---|
| ECG | |
| Color Coding | |
| Color Coding | Sp02 |
Sensor Type
989803172031| AAMI color coded
grabber connectors| 989803172051| AAMI color coded
grabber connectors| Finger wrap
sensor
989803172131| IEC color coded
grabber connectors| 989803172151| IEC color coded
grabber connectors| Finger wrap
sensor
*All ECG leads are 0.85m (34 in) long.
**The cable for the attached SpO2 sensor is 2m (6.5 ft) long. The preferred
SpO2 patient application site is any finger except a thumb.
Warnings
- These patient cables are for single patient use only. They should never be reused on a different patient due to risk of cross-infection.
- To avoid patient injury, assure that leadset is not positioned where leads could become entangled around patient, or cause choking, strangulation, or inhibit circulation in extremities.
- Protect the patient cable trunk connector, ECG lead connectors, and SpO2 sensor from becoming soaked with any liquid.
Patient Application
Visually inspect the ECG leadset (and SpO2 sensor/cable when present) before applying the patient cable to a patient.
- If any signs of damage or deterioration are seen, immediately discard the patient cable following approved medical waste disposal methods specified by local regulations or your patient care facility.
- If no visual damage is seen, apply the ECG leads to the patient following standard AAMI or IEC practices (refer to the IntelliVue MX40 Instructions for Use).
- If the patient cable includes a SpO2 sensor, follow the sensor application instructions supplied in the IntelliVue MX40 Instructions for Use. If the SpO2 sensor is not being used, be sure to securely store the sensor inside the telemetry pouch.
- Recommended SpO2 sensor application site is any finger except the thumb.
Additional Information
For more detailed information describing patient cable use with the MX40, including warnings, patient safety, and ECG/SpO2 patient application instructions, refer to the IntelliVue MX40 Instructions for Use.
Product Symbols
Product packaging symbols are defined below:
For more information, please call the local Philips sales office listed in your telephone directory; or contact one of the regional sales offices listed below for the location of your nearest Philips sales office.
United States:
Philips Medical Systems
North America Corporation
3000 Minuteman Road
Andover, MA 01810-1099
+1 800 225-0230 toll free
Canada:
Philips Medical Systems Canada
281 Hillmount Road
Markham, ON
L6C 2S3
800-291-6743
Latin America Headquarters:
Philips Healthcare Brazil
Rua Verbo Divino 1400 – 7° Andar
Chacara Santo Antonio
04719-002 Sao Paulo, SP
Brazil
Tel: +55 11 2125-0744
Fax: +55 11 2125-0761
Contains no Latex
US Status: Distributed by Philips Medical Systems Made in Germany
Manufacturing Address:
Philips Medical Systems
3000 Minuteman Road
Andover, MA 01810-1099 USA
Tel: 800-225-0230
http://philips.com/healthcarestore
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>