UltraLux LITH6018CCT LED Industrial Light Installation Guide
- June 3, 2024
- ULTRALUX
Table of Contents
UltraLux LITH6018CCT LED Industrial Light
INSTALLATION
LED INDUSTRIAL LIGHT -Model: LITH6018CCT
This product contains a light source of energy efficiency class C
LED INDUSTRIAL LIGHT – Model: LITHl 2036CCT
This product contains a light source of energy efficiency class C
LED INDUSTRIAL LIGHT – Model: LITHl 5033CCT
This product contains a light source of energy efficiency class C
LED INDUSTRIAL LIGHT – Model: LITHl SOSSCCT
This product contains a light source of energy efficiency class C.
Tri-Colour CCT selectable 36op Ha l.lBeTHa reMneparypa
Change the CCT by switch on the PCB selecting 3000K, 4000K or 6SOOK light
Power selectable 36op Ha MOLI.IHOCT
Change the power by DIP Switch on the driver.
LITH6018CCT
| Power/ MOll.\HOCT | 10W | 13W | 16W | 18W |
|---|---|---|---|---|
| PIN1 | OFF | OFF | ON | ON |
| PIN2 | OFF | ON | OFF | ON |
LITH12036CCT
| Power/ Moll.\HOCT | 19W | 24W | 29W | 36W |
|---|---|---|---|---|
| PIN1 | OFF | OFF | ON | ON |
| PIN2 | OFF | ON | OFF | ON |
LITH1S033CCT
| Power/ Moll.\HOCT | 19W | 24W | 28W | 33W |
|---|---|---|---|---|
| PIN1 | OFF | OFF | ON | ON |
| PIN2 | OFF | ON | OFF | ON |
LITH15055CCT
| Power/ Moll.\HOCT | 31W | 39W | 47W | SSW |
|---|---|---|---|---|
| PIN1 | OFF | OFF | ON | ON |
| PIN2 | OFF | ON | OFF | ON |
WARNING: Installation should be done by registerd electricians.
NOTE: READ THE INSTRUCTIONS BEFORE MOUNTING
-
Performing any activity with the power supply on constitutespotential hazard of electric Prior to mounting, power supply must be switched off by using the main switch.
-
The fixture can be installed only on a flame-resistant base with ignition temperature at least 200°c and does not deform or soften (e.g. metal, concrete, plaster).
-
Activities related to connection to the power supply are to be commissioned to a person with appropriate a authorization.
-
The fixture, when properly assembled, may only be connected to a properly functioning electrical system with compliance with the applicable standards.
-
Connect the fixture to the electrical supply, observing the correct polarity.
(L) LIVE:BROWN; EARTH:GREN/YELLOW;(NJ NEUTRAL:BLUE -
All conductors and fitting auxiliary components are to be placed on appropriate distance from the heating parts of the When choosing the place for mounting, the required minimum distance must be kept between the fitting and the lightened objects.
-
Prior to replacing, it is necessary to cut off the power supply by main switch.
-
Clean only with dry cloth.
-
The light fixture heat itself while working, so in case of necessity prior to undertaking its replacement, wait until cool down.
-
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
-
Do not cover the To avoid any fire hazard, provide unrestricted air flow to the heated fitting parts.
-
Not suitable for accent lighting.
-
Prior to starting operating, make sure the mounting of the product has been performed appropriately, eliminating the hazard of defective operation, not endangering the surrounding and the users.
-
The importer/supplier bears no responsibility for damages resulting from failure to comply with these Instructions.
TAKE CARE OF THE NATURAL ENVIRONMENT CLEANLINESS
The product sand its components are not dangerous for the environment.
Please dispose all the package elements separately into the appropriate
corresponding material containers.
Please dispose all broken lighting fixtures separately in containers for out
of usage electrical equipment.
Before disposing the WEEE contact the importer/supplier or refer to the
guidelines of your local environment protection organizations.