UltraLux MNSCRF6A RF Dimmer for Single Color LED Strip Instruction Manual

UltraLux MNSCRF6A RF Dimmer for Single Color LED Strip

Specifications

• Product: RF LED Dimmer
• Model: MNSCRF6A
• Description: Miniature constant voltage dimmer for single-color LED strips
• Control: RF remote control (up to four paired remotes)

The MNSCRF6A is a dimmer designed for single-colour LED strips, controllable by up to four paired RF remote controls of the same model.

FAQ

• Q: How many scene modes does the dimmer have?
• A: The dimmer has four scene modes that can be saved in memory for quick access.
• Q: Can the dimmer be controlled by multiple RF remote controls?
• A: Yes, the dimmer can be controlled by up to four paired RF remote controls of the same model.

DESCRIPTION

• MNSCRF6A is a miniature constant voltage dimmer designed for single-color LED strips.
• It is controlled by up to four paired RF remote controls of the same model.

TECHNICAL INFORMATION

• Input/Output voltage: 12-24 V DC
• Max. output current: 6 A
• IP rate: IP20
• Max. output power: 72 W (12 V DC); 144 W (24 V DC)
• RF frequency: 433.92 МHz
• Remote distance: max. 20 m
• Dimensions: 48/26/13 mm
• Working temperature: -10⁰ C ÷ +40 ⁰ C
• Warranty: 2 years

IMPORTANT: READ THE INSTRUCTIONS BEFORE INSTALLATION OR REPLACEMENT!

• Performing any actions while the electrical voltage is on carries the potential danger of electric shock. The power supply must be turned off before starting any work.
• The dimmer should be connected to a power supply from a properly installed electrical system that complies with current requirements. Installation should be carried out according to this manual by a qualified specialist.
• The importer (supplier) is not responsible for damages resulting from the non-compliance with the above-mentioned installation recommendations.

CONNECTION DIAGRAM

NOTE

• Ensure that the power supply voltage and the LED strip voltage match (12-24 V DC).
• The dimmer can be controlled with up to four paired RF remote controls.
• When connecting, be sure to observe the polarity.
• Do not install on flammable surfaces.
• Do not cover individual components. Provide sufficient space for cooling.

DESCRIPTION OF RF THE REMOTE CONTROL

BRIGHTNESS LEVEL 25%| BRIGHTNESS LEVEL 50%| BRIGHTNESS LEVEL 75%| BRIGHTNESS LEVEL 100%
SCENE 1| SCENE 2| SCENE 3| SCENE 4

Delay-off 30 s

|

Brightness/Speed –

|

Brightness/Speed +

| Dynamic mode

(flashing и fading)

SCENE MODE
The dimmer has 4 scenes (a set of settings) that can be saved in memory. If needed, pressing the button on the dimmer quickly activates the saved settings.

1. Press the “SCENE 1” button three times within 5 seconds. The brightness of the lighting will decrease. This means that the controller is in the settings input mode.
2. Use the remote control buttons to adjust the desired settings.
3. Press the “SCENE 1” button once. The brightness of the lighting will decrease. This indicates that the settings have been saved successfully.
4. Press the “SCENE 1” button once. The controller immediately transitions to the previously saved settings.

PAIRING И UNPAIRING

• Pairing is the process of connecting new RF control devices.
• The dimmer remembers the last four paired remote devices.
• On the other hand, unpairing is a process after which the dimmer can be controlled by an unlimited number of RF remote devices of the same model.

Pairing

1. Turn off the power.
2. Press and hold the button „Delay-off 30 s“.
3. While holding down the button, turn on the power. The lighting will decrease its brightness to 50%.
4. Press the “Delay-off 30 s ” button three times within 3 seconds. Upon the first press, the brightness of the lighting will go to a level of 25%. Upon the second press, the brightness of the lighting will go to a level of 10%. Upon the third press, it will return to its current state.
5. If pairing is unsuccessful, repeat steps 1 to 4.

Unpairing

1. Turn off the power.
2. Press and hold the button „Dynamic mode“.
3. While holding down the button, turn on the power. The lighting will decrease its brightness to 50%.
4. Press the ” Dynamic mode” button three times within 3 seconds. Upon the first press, the brightness of the lighting will go to a level of 25%. Upon the second press, the brightness of the lighting will go to a level of 10%. Upon the third press, it will return to its current state.
5. If unpairing is unsuccessful, repeat steps 1 to 4.

TAKING CARE OF THE NATURAL ENVIRONMENT CLEANLINESS

• The product and its components are not harmful to the environment.
• Please dispose of the package elements separately in containers for the corresponding material.
• Please dispose of the broken product separately in containers for out-of-usage electrical equipment.

www.ultralux.bg.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>