ULTRALUX Lighting Utility LED Slim Flush Mount Installation Guide
- June 3, 2024
- ULTRALUX
Table of Contents
Lighting Utility LED Slim Flush Mount
Installation Guide
INSTALLATION INSTRUCTIONS
PN: UL-LED-USFMXX-XXXX
Thank you for purchasing ULTRALUX’s LIGHTING Fixtures!
TROUBLESHOOTING
- Check that the line voltage at the fixture is correct.
- Ensure that there is the voltage at lamp fixture wires. If there is no voltage, then check all connections.
- Check that fixture is grounded properly. If the fixture does not light:
- Check the switch to ensure that there are no defects.
- Check fuse/circuit breaker for trips, then check wiring connections.
CLEANING AND MAINTENANCE
CAUTION: Ensure the fixture temperature is cool enough to touch.
DO NOT clean or perform maintenance while the fixture is energized.
- Clean lens and Suite with a non-abrasive cleaning solution.
- Do not open the fixture to clean LED. Do not touch the LED.
- Do not spray liquid directly on to LED, LED driver, or wiring.
Please read carefully before installing the fixture. Save these instructions,
as you may need them at a later date.
Please follow the following steps for installation.
WARNINGS
Turn the power off before installation, inspection, or removal. Use all
necessary precautions while performing this procedure.
Consult a qualified electrician to ensure the correct branch circuit
conductor. Min 90°C supply conductors.
Properly ground electrical enclosure. IT IS IMPERATIVE THAT THE JUNCTION BOX
BE PROPERLY GROUNDED.
DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS, OTHERWISE, SAFETY WILL BE
COMPROMISED.
This Integrated LED Fixture has no lamp/bulb to replace.
Do not remove or touch the inside of the plastic lens covering the LED board.
GENERAL: All electrical connections must be in accordance with local and
National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper
electrical wiring connections, contact and obtain the services of a qualified
electrician. Use UL or IEC-approved wire only for input/output connections.
Remove the fixture and mounting components from the box, and make sure that no
parts are missing by referencing the illustration in the installation
instructions.
DIMMING: This product is compatible with the most common residential-type
dimmers. Dimming performance will depend upon the dimmer, dimmer settings
(dimmers with adjustments to brightness range), wiring method, and the number
of LED modules. For best results, set the dimmer position at maximum before
adjusting to a lower light level.
1. JUNCTION BOX (NOT INCLUDED)
2. MOUNTING BRACKET
3. FIXTURE SCREWS (x2)
4. MOUNTING SCREWS (x2)
5. WHITE SUPPLY WIRE
6. BLACK SUPPLY WIRE
7. SUPPLY GROUND WIRE| 8. WHITE FIXTURE WIRE
9. BLACK FIXTURE WIRE
10. FIXTURE GROUND WIRE
11. WIRE NUT (x3)
12. FIXTURE PAN
13. FIXTURE LENSE
---|---
- SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER!
- Remove contents from the box. Ensure that no parts are missing. Reference the illustration included with this instruction manual.
- Pull the SUPPLY WIRES (5 Et 6) and the SUPPLY GROUND WIRE (7), out from the JUNCTION BOX (1).
- Place the MOUNTING BRACKET (2) over the JUNCTION BOX (1) and align the slots of the bracket with the screw holes in the junction box. Slide the MOUNTING SCREWS (4) through the holes of the MOUNTING BRACKET (2) and thread into the appropriate holes of the JUNCTION BOX (1). Then, fasten MOUNTING SCREWS (4) tightly.
- Make the following wire connections (Fig.1), using WIRE NUTS (11): WHITE (NEUTRAL/COMMON) SUPPLY WIRE (5) TO WHITE FIXTURE WIRE (8) BLACK (LINE) SUPPLY WIRE (6) TO BLACK FIXTURE WIRE (9) SUPPLY GROUND WIRE (7) TO FIXTURE GROUND WIRE (10) If necessary, wrap all wire connections in electrical tape to ensure a secure connection.
- Carefully tuck all wiring back into the JUNCTION BOX (1).
- Align the screw holes of the FIXTURE PAN (12) to the holes in the MOUNTING BRACKET (2).
- Attach the FIXTURE PAN (12) to the MOUNTING BRACKET (2) by feeding the FIXTURE SCREWS (3) through the holes of the fixture and into the holes of the bracket. Then, fasten FIXTURE SCREWS (8) tightly.
- Attach the LENS (13) by rotating clockwise until secure.
- Restore power at fuse box/circuit breaker. Check the operation of the Integrated LED Fixture.
- Installation complete.
5-YEAR LIMITED WARRANTY
LIMITED WARRANTY: This fixture is warranted to be free from defects in
workmanship and material for up to 5-years. Based upon reasonable household
usage, when used in accordance with the package and included instructions. If
this fixture does not last for the time period guaranteed, the manufacturer
will send you a replacement fixture upon receipt of the returned fixture,
register receipt, and proof of purchase. To contact us, please email us at
returns@ultraluxled.com or call us at
1-800-316-2532 to find out how to
return the fixture. We are committed to making high-quality products.
Returning the fixture will help us monitor and further improve product
quality. This replacement is the sole remedy available, and LIABILITY FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED.
This device complies with Part 15 of the FCC Rules and has been tested and
found to comply with the limits for Class B digital devices. Operation is
subject to the following two conditions: (7) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
Toll-Free: 1-800-316-2532
www.ultraluxled.com
@ 2021 ULTRALUX° LIGHTING is a registered trademark of Superior Ventures
LLC. All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>