Bissell 9595, 3918, 24101, 7482, 2412 Series Cleanview User Guide

Bissell 9595, 3918, 24101, 7482, 2412 Series Cleanview

Thanks for buying a BISSELL vacuum

We’re glad you purchased a BISSELL vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system.

Your BISSELL vacuum is well made, and we back it with a limited warranty. We also stand behind it with a knowledgeable, dedicated Consumer Care department, so, should you ever have a problem, you’ll receive fast, considerate assistance.

My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global leader in the design, manufacture, and service of high quality homecare products like your BISSELL vacuum.

Thanks again, from all of us at BISSELL.

Mark J. Bissell
Chairman & CEO

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM.
Always connect to a polarized outlet (one slot is wider than the other). Unplug from outlet when not in use and before conducting maintenance. When using an electrical appliance, basic precautions should be observed, including the following:

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:

• Always connect to a polarized outlet (one slot is wider than the other). Do not modify the polarized plug to fit a non-polarized outlet or extension cord.

• Do not leave vacuum cleaner when it is plugged in. Unplug from outlet when not in use and before servicing.

• Do not use outdoors or on wet surfaces.

• Do not allow to be used as a toy. Close attention is necessary when used by or near children.

• Do not use for any purpose other than described in this User’s Guide. Use only manufacturer’s recommended attachments.

• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.

• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not handle plug or vacuum cleaner with wet hands.

• Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.

• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

• Turn off all controls before plugging or unplugging vacuum cleaner.

• Use extra care when cleaning on stairs.

• Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.

• Do not use vacuum cleaner in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors.

• Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).

• Do not pick up anything that is burning or smoking, such as
  cigarettes, matches, or hot ashes.

• Do not use without filters in place.

• Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.

• Use only on dry, indoor surfaces.

• Keep appliance on a level surface.

• Do not carry the vacuum cleaner while it is running.

• Unplug before connecting or disconnecting the TurboBrush® Tool.

SAVE THESE INSTRUCTIONS FOR FUTURE USE
This model is for household use only.

THIS APPLIANCE HAS A POLARIZED PLUG
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a proper outlet. Do not change the plug in any way.

Quick Start Guide

CARTON CONTENTS

A. Vacuum Base
B. Handle
C. Screws (2)
D. Upper Cord Wrap
E. Hose Wand Clip
F. TurboBrush® tool
G. Dusting Brush
H. Hose
I. Crevice Tool*
J. Extension Wand
*Note: Crevice tool is located inside Extension Wand

Product View

1. Handle
2. Power switch (select models)
3. Tank Release Button
4. Carry Handle
5. Suction Power Indicator (select models)
6. Lid Release Button
7. Pre-Motor Filter (located inside Dirt Tank lid)
8. Bottom Easy Empty™ Dirt Tank
9. Post-Motor Filter
10. Height Adjustment Knob
11. Brush Roll On/Off (select models)
12. Furniture Protection Guard
13. Powerfoot
14. Cord Clip
15. TurboBrush® Tool
16. Upper Hose Wrap
17. Dusting Brush
18. Stretch Hose
19. Upper Cord Wrap
20. Crevice Tool
21. Extension Wand
22. Extension Wand Clip
23. Power Switch (select models)
24. Hose Wand
25. Hose Wand Base
26. Handle Release Pedal
27. Foot Hose
28. Power Cord
    

WARNING: Plastic film can be dangerous. To avoid danger of suffocation, keep away from babies and children.

WARNING: Do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures.

WARNING: To reduce the risk of electric shock, turn power switch off and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks.

Assembly

The only tool you’ll need to assemble your vacuum cleaner is a Phillips-head screwdriver.

WARNING: Do not operate vacuum with damp or wet filters or without all filters in place first

Attach handle to vacuum

1. Locate the vacuum handle and remove the screw packet taped to the handle. The screw packet contains two screws of equal length.

2. Stand the vacuum upright and slide the base of the handle firmly into the opening at the top of the vacuum body.
   

3. Check to be sure the handle is fitted to the vacuum body. If there are any gaps between the handle and the vacuum base, continue to push the handle firmly into the base until the handle is flush.

4. Insert the two screws from the screw packet into the existing holes. Push each screw firmly into the hole before beginning to secure the screw with a Phillips head screwdriver. If the handle is aligned properly on the vacuum base, you should be able to push the screw almost entirely into the hole until only the screw head is visible. Tighten the screw with a Phillips head screwdriver by rotating the screw clockwise.
   

Attach vacuum hose, clips & tools

1. Attach the extension wand clip by inserting the clip into the back of the vacuum base and twisting clockwise. Mount the extension wand (with crevice tool inside) on the back of the vacuum.
   

2. Snap the upper cord wrap into the socket located above the extension wand clip. Wrap the power cord around the cord wrap clips.

3. Attach the Twist ‘n Snap™ hose by lining up the tabs on the cuff with the corresponding notches on the back of the vacuum. Twist the Twist ‘n Snap hose clockwise to lock the hose into place.

4. Slide the end of the hose wand into the hose wand base, and fold the hose over the upper hose wrap.
   
   NOTE: The powerfoot will not suction properly unless the hose wand is firmly attached.

5. Slide the dusting brush into the opening below the upper hose wrap.

6. The TurboBrush Tool secures to the back of the handle in the mount above the Upper Hose Wrap.
   

Operations

CAUTION: Before using your vacuum, make sure that the dirt tank is in the locked position and that both filters (pre-motor and post-motor) are in place. Do not operate your vacuum without these filters.

Power switch

The Power switch on model 9595, 3918, 24101, 7482 series is located on the left side of the vacuum. Push the rocker switch “ON” (I) to vacuum, and “OFF” (O) when cleaning is complete. The Power switch on model 2412 is located on the front of the handle. Push the button once to vacuum, and push the button again when cleaning is complete.
NOTE: You can find your model number on the back, bottom side of the vacuum on the white sticker by the UL rating.

Handle position

Press the handle release pedal with your foot to place your CleanView vacuum into one of three cleaning positions.

1. Upright – For storage and above floor cleaning with tools.
2. Normal cleaning – Press handle release for household floor cleaning tasks.
3. Low cleaning – With the vacuum in normal cleaning position, press handle release pedal again, use for reaching under low furniture such as tables, chairs or beds.
   

Height adjustment

There are five height settings available for various floor surfaces. Turn the dial on the foot of the cleaner to the desired setting.
Lowest setting – For low pile carpet or bare floors. To pick up debris, it may be necessary to move up one setting.
Medium setting – For medium pile carpet.
Highest setting – For high pile and most shag carpet.

NOTE: For optimal carpet cleaning performance, adjust to the lowest practical setting. If your cleaner is difficult to push, adjust to the next higher setting.
If the dial is difficult to turn, tilt the cleaner back slightly to take the weight off the foot while turning.

Tips:

• Hair, string and small objects can block the vacuum hose or tools. Check them occasionally for obstructions.
• Before cleaning under low furniture, check area first for objects that might harm the unit or block the vacuum hose.
• Your vacuum features a Quick Release™ cord wrap. To remove the power cord quickly and easily, rotate the upper cord wrap toward the floor and slip the power cord off the upper and lower cord wraps.

Brush Roll On/Off (On model series: 7482 & 2412)

The rotating brush On/Off pedal is located on the front of the vacuum base. You can use your foot to engage or disengage this pedal (a). When the brush roll pedal has been engaged, the brush will start rotating. The brush roll should be turned on for most carpeted floors. To turn the brush roll off, disengage the pedal by pressing on it with your foot. We recommend turning off the brush roll for bare floor cleaning to prevent scatter or for other delicate surfaces.

NOTICE: The floor brush will continue to rotate while you use your vacuum for above floor cleaning. To prevent carpet damage, do not lean on the vacuum or let the powerfoot tilt forward.

Transporting cleaner

1. To move your cleaner from room to room, put the handle in the upright position, tilt the cleaner back on its rear wheels and push forward.
2. The cleaner can also be moved by using the carrying handle.

Suction Power Indicator (On model series: 2412)

The suction power indicator tells you when the air flow in your vacuum is reduced due to dirty filters or a clog in the hose. The suction power indicator will remain green until the airflow is reduced. At that time, it begins to change to red.

When it is fully red, the airflow is significantly reduced by a dirty filter or clog. Follow the steps down below for clearing a clog. Follow the steps down below to clean your filters. All filters in the vacuum should be cleaned or replaced when the clean filter indicator turns red.
NOTE: When your vacuum is turned off, the suction power indicator will go to the green color setting. The suction power indicator only detects reductions in airflow when the vacuum power is on.

Tip: Hair, string and small objects can block the vacuum hose or tools. Check them occasionally for obstructions.

WARNING: The rotating floor brush continues to rotate while tools are in use. To reduce the risk of injury from moving parts, always move the cleaner with the carrying handle at the back of the cleaner. Always place vacuum cleaner on floor with handle in upright position when using tools. Never place your fingers under the cleaner when it is running. Never place powerfoot on furniture or uneven surfaces. Do not place vacuum cleaner close enough to objects to pull them into rotating brush.

Special tools

Your BISSELL CleanView vacuum is not only a powerful carpet and rug vacuum cleaner, it’s also a versatile above floor vacuum cleaner when you select one of the special tools.

1.  Raise handle to upright position.
2. Grasp the hose wand and separate from the hose wand base.
3. Attach tools by firmly pushing onto vacuum hose or extension wand.
   a. Crevice tool Use in tight narrow spaces.

b. Dusting Brush Use brush to dust furniture, blinds, books, lamps, shelves and baseboards.

c. Extension wand Use with desired attachment for a longer reach.

d. TurboBrush® Tool Use rotating brush action for small flat areas such as stairs and cushions. Press gently down and pull toward you in a raking motion; too much pressure will cause the brush to stop rotating.

NOTICE: While vacuuming, certain carpets and low humidity conditions may generate small static discharges. The discharges are entirely harmless and are not associated in any way with the main power supply.

Tip: The crevice tool is located inside the wand

Maintenance & Care

WARNING: To reduce the risk of electric shock, turn power switch off and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks.

To maintain maximum cleaning performance, the following maintenance steps must be performed:

1. Empty the dirt tank when the dirt reaches the “Full” line on the side.

2. Check the pre-motor filter at least once a month and clean or replace as needed. To access the pre-motor filter, remove the Easy Empty dirt tank from the vacuum base and push the lid release button located on the carry handle.
   
   Remove the foam filter from the filter tray.

3. The post-motor filter assists in the filtration process to return clean air to the room. Replace the post-motor filter every three to six months.
   To access the post-motor filter, remove the filter tray located below the Easy Empty dirt tank. When the filter becomes dirty, push the filter through the bottom of the tray to clean or replace the filter.
   
   NOTE: The pleated post-motor filter may NOT be washed with water or detergent. If dust and/ or debris accumulates on the filter, gently tap the filter on the side of a garbage container.
   Note: More frequent filter cleaning or replacing may be necessary if you are vacuuming new carpet, fine dust, or have allergy concerns. Follow the instructions on the following pages to perform these simple maintenance steps.

Empty Dirt Tank

The dirt tank needs to be emptied when the dirt reaches the “Full” line on the side of the tank.

1. Unplug cleaner from electrical outlet.

2. Remove the Easy Empty dirt tank from the vacuum base by pushing the tank release button.

3. Hold the dirt tank over a garbage container.
   Press the bottom lid release button on the back of the dirt tank to empty dirt.

4. Mount the Easy Empty dirt tank back on the vacuum base.
   NOTE: The dirt tank may be washed in warm water with a mild detergent. Make sure it is completely dry before replacing.

Cleaning the pre-motor filter and inner cyclone

Use only genuine BISSELL replacement filters in your BISSELL CleanView vacuum.

1. Unplug the cleaner from electrical outlet.
2. a. Remove the Easy Empty dirt tank and locate the pre-motor filter as described on the previous page.

b. Remove the foam filter from the filter tray. The filter tray is fixed in-place, but may be removed for cleaning by unscrewing the tray. The foam filter and tray may be hand washed in warm water with a mild detergent, if desired. Rinse well, then air dry thoroughly before replacing the filter. Make sure all components are completely dry before replacing.

3. The inner cyclone may also be removed for cleaning. With the bottom of Easy Empty dirt tank open, reach up into the dirt cup and grasp the cyclone. Twist the cyclone clockwise to unlock and pull straight down to remove. The inner cyclone and dirt cup may be wiped clean with a damp cloth. Make sure all parts are dry before replacing.

WARNING: Do not operate cleaner with damp or wet filters or without all filters in place.

Tip: When replacing the inner cyclone after cleaning, open the pre-motor filter lid to help guide the inner cyclone into the grooves at the top of the tank. Twist counterclockwise to lock the inner cyclone into place.

NOTICE: Do not place the dirt tank or other product components in the dishwasher. Hand wash only

Replacing the post-motor filter

Use only a genuine BISSELL replacement post-motor filter in your BISSELL CleanView vacuum.

1. Unplug the cleaner from electrical outlet.
2. The post-motor filter assists in the filtration process to return clean air to the room. Replace the post-motor filter every three to six months. To access the post-motor filter, remove the filter tray located below the Easy Empty dirt tank. When the filter becomes dirty, push the filter through the bottom of the tray to clean or replace the filter.
   
   NOTE: The pleated post-motor filter may NOT be washed with water or detergent. If dust and/ or debris accumulates on the filter, gently tap the filter on the side of a garbage container.

Checking rotating floor brush and drive belt

You should check your vacuum cleaner’s rotating floor brush and drive belt regularly for wear or damage. You should also clean the brush and brush ends of strings, hair and carpet fibers.
These can wrap around the brush and hamper its ability to effectively clean your carpet. Also remove any debris that has accumulated under the brush cover.

1. Unplug cleaner from electrical outlet.

2. Place handle in low position and turn vacuum cleaner over so bottom side is up.

3. Remove the seven screws with a Phillips head screwdriver. Lift the brush cover off.
   

4. Grasp rotating floor brush at both ends and lift straight out of the vacuum foot. Slip off the belt.
   

5. Clean strings, hair and other debris from rotating floor brush, paying particular attention to brush ends.

6. Clean strings, hair and other debris from motor pulley and drive belt areas.

7. Check drive belt carefully for wear, cuts or stressed areas, and replace if necessary (see instructions ).

8. Check air passageway for obstructions. Remove debris from this area.
   

Replace drive belt

Use only a genuine BISSELL style 9 replacement belt (#203-1093) in your BISSELL CleanView vacuum.

1. Unplug cleaner from electrical outlet.

2. With rotating floor brush removed from vacuum cleaner (steps 1-4 of Check rotating floor brush and drive belt), grasp old drive belt and remove from motor pulley. Discard old drive belt.

3. Place new drive belt over motor pulley and stretch other end over rotating floor brush in the space between the bristles.

4. Place ends of rotating floor brush down into slots on sides as shown.
   

5. Turn rotating floor brush by hand several times in the direction of motor pulley. If properly installed, drive belt will center itself on rotating brush.

6. Reposition the brush cover and screw all seven screws back into place.

WARNING: To reduce the risk of injury from moving parts, turn off vacuum cleaner and disconnect Power Plug from electrical outlet.

Clearing a clog

Low suction or poor pickup may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action of the dirt or brush roll, check for clogs.

1. Unplug cleaner from electrical outlet.

2. Remove Easy Empty dirt tank from vacuum base and empty dirt and debris.

3. Remove inner cyclone from Easy Empty dirt tank (check above) and check for debris build-up or clogs in the upper tank.

4. Check the suction inlet for a clog.
   

5. Grasp the hose wand to separate from the hose wand base. Check for a clog in the base, the wand or within the hose.

6. Remove the screw attaching the hose wand base to the vacuum. Straighten the hose wand base and check for clogs with a long, narrow object such as a broom stick. Do not use sharp objects like a clothes hanger, as these may puncture the hose.
   

7. If the clog persists, follow the instructions for Checking the rotating floor brush check above and inspect the air passageway for obstructions.

Troubleshooting

WARNING: To reduce the risk of electric shock, turn power switch off and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks.

electrical plug
Blown fuse/tripped breaker| Check/replace fuse or reset breaker
Vacuum cleaner won’t pick up dirt| Incorrect height adjustment| Adjust powerfoot to correct height setting
Hose not attached to suction opening| Grasp the hose wand and firmly push into the hose wand base
Crack or hole in hose| Check hose and replace if needed
Broken or worn drive belt| Replace drive belt, check above
Rotating floor brush bristles worn| Replace brush
Rotating floor brush jammed| Remove brush and clean debris from brush ends, check above.
Clog in vacuum| Follow instructions above for clearing clogs
Dirt tank full| Empty dirt tank
Dirt tank or upper tank not installed properly| Position correctly and lock in place
Filters are dirty| Check and clean or replace pre-motor and post-motor filters, check above
Tool won’t pick up| Crack or hole in hose| Check hose and replace if needed
Clog in vacuum| Follow instructions above for clearing clogs
Dirt tank full| Empty dirt tank
Dirt tank or upper tank not installed properly| Position correctly and lock in place
Filters are dirty| Check and clean or replace pre-motor and post-motor filters check above.
Vacuum cleaner difficult to push| Incorrect height adjustment| Adjust powerfoot to correct height setting
Visible dirt escaping from cleaner| Dirt tank full| Empty dirt tank
Filters missing or installed incorrectly| Check pre-motor and post-motor filters for correct installation

Please do not return this product to the store.
Other maintenance or service not included in the manual should be performed by an authorized service representative.
Thank you for selecting a BISSELL product.
For any questions or concerns, BISSELL is happy to be of service. Contact us directly at 1-800-237-7691.

Replacement Parts

These items are available for your BISSELL CleanView Vacuum.
Call 1-800-237-7691 or visit www.bissell.com

PART #| PART NAME|
---|---|---
160-1506| Brush Roll (15”) (7482 & 2412 Series)|
1008| Filter Pack (includes one pre-motor filter and one post-motor filter)|
203-2665| Hose Assembly|
160-0159| Brush Roll (13.5”) (9595, 3918, 24101 Series)|
203-1093| Style 9 Drive Belt (2-Pack)|
1215| Febreze® Post-Motor Filter* (fits all CleanView vacuums)|

Accessories

These items are available for your BISSELL CleanView Vacuum.
Call 1-800-237-7691 or visit www.bissell.com

PART #| PART NAME|
---|---|---
203-1429| TurboBrush Tool|
203-2666| Extension Wand (11”)|
203-1527| Dusting Brush|
203-1056| Crevice Tool|

Warranty

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Care by E-mail, telephone, or regular mail as described below.
CleanView® 9595 series –

Limited Two-Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for two years any defective or malfunctioning part.
CleanView® 3918, 24101, 7482, 2412 series –

Limited Three-Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for three years any defective or malfunctioning part.

See information on “If your BISSELL product should require service”.

This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User’s Guide is not covered.

BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS
WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE THREE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.

Some states do not allow limitations on how long an implied warranty last so the above limitation may not apply to you.

NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim.

Service

If your BISSELL product should require service:
Visit BISSELL.com or contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Care.

Website or E-mail: www.BISSELL.com

Or Call:
BISSELL Consumer Care
1-800-237-7691
Monday – Friday 8am – 10pm ET
Saturday 9am – 8pm ET
Sunday 10am – 7pm ET

Bissell 9595, 3918, 24101, 7482, 2412 Series Cleanview User Guide – Download [optimized]
Bissell 9595, 3918, 24101, 7482, 2412 Series Cleanview User Guide – Download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>