PHILIPS RC136B LED Panel Installation Guide

June 4, 2024
Philips

PHILIPS RC136B LED Panel

WHAT IS IN THE BOX

PHILIPS RC136B LED Panel-1PHILIPS RC136B LED
Panel-3 Optional: PHILIPS RC136B LED Panel-4PHILIPS RC136B LED
Panel-5 PHILIPS RC136B LED Panel-6SETTINGPHILIPS RC136B
LED Panel-7 PHILIPS RC136B LED Panel-8 PHILIPS RC136B LED
Panel-9 INSTALLATIONPHILIPS RC136B LED Panel-10 PHILIPS RC136B
LED Panel-11 INRUSH CURRENT

  • The luminaire shall be installed by a qualified electrician and wired in accordance with the latest IEE electrical regulations or the national requirements.
  • The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
  • During installation or maintaining the luminaire please use gloves to avoid spots on the cover.
  • To remove dirt and spots use the following: Dust: use microfiber cloths only.
  • Fingerprints, etc.: use a cleaner for synthetic materials with antistatic properties.
  • Luminaires are not suitable for covering with thermally insulating material
  • Luminaires must not be used or stored in a corrosive environment where hazardous materials such as Sulphur, Chlorine, Phthalates, etc, are present.
  • Only to be installed outside arm’s reach.
  • If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similarly qualified person in order to avoid a hazard.

According to the new ErP requirement

This product contains a light source of energy efficiency class.
Storage, installation, use, operation and maintenance of the products needs to be performed exactly according to the instructions in this manual and/or other instructions as may be provided by us to guarantee safe use of the product over its entire lifetime. Failure to adhere to these instructions will invalidate your entitlement to a warranty. Bolts with an indication of torque strength on the drawing need to be tightened using a calibrated torque wrench. Pre-assembled bolts need to be retightened again to the required torque specification to assure maximum strength over a lifetime.

SR compatibility – For SR-based luminaires, only SR-Certified components/sensors are to be used (see also: http://www.lighting.philips.eo.uk/oem-emea/products/driving­connected- lighting). The functional compatibility of two (SR-certified) components/sensors to be used in combination, as well as the override possibility of any line-switch function used in an SR-based luminaire, is to be released by the master component/sensor supplier. If using a NEMA 7-pin socket on an SR-based luminaire, a full system verification is required. Not following this advice can/will cause risk of damage and non-compliance for which Signify cannot take any responsibility.
Please inform yourself about the local waste disposal, separation and collection system for electrical and electronic products and packaging. Please act according to your local rules and do not dispose of your old product and packaging with your normal household waste. The correct disposal of the packaging, your product, and/or batteries will help prevent potential negative consequences for the environment and human health. Batteries should be disposed of separately from the municipal waste stream via designated collection facilities. When disposing of a product that contains non-user- replaceable batteries, the non-user replaceable batteries shall be removed by a professional.
luminaire has basic insulation between Low Voltage supply and control conductors The control gear and/or the external flexible cable contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person. The light source contained in this luminaire is not replaceable, n case of damage replace the luminaire.

all rights reserved This document contains information relating to tt1e product portfolio of Signify which information may e subject to change. No representation or warranty as to the accuracy or completeness of the information included herein given and any liability for any action in reliance thereon is disclaimed. The information presented in this document is not tended as any commercial offer and does not form part of any quotation or contract. Philips and the Philips Shield emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify
Holding or their respective owners. signify Holding. he Netherlands

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals