Spectrum Netremote: User Guide for Spectrum Remote Control

The Spectrum Netremote is a versatile remote control that can be programmed to work with a variety of devices, including TVs, cable boxes, and audio equipment. To get started, users need to install two AA batteries and pair the remote with their Charter WorldBox or other cable box. The user guide provides step-by-step instructions for programming the remote for any device, including popular TV brands. The guide also includes troubleshooting tips for common issues, such as unresponsive equipment or difficulty pairing the remote. Additionally, the guide features a comprehensive key chart that outlines the function of each button on the remote. Users can refer to this chart to find the right button for their desired action. Finally, the guide includes a Declaration of Conformity that outlines the FCC regulations for this device. Overall, the Spectrum Netremote User Guide is an essential resource for anyone looking to get the most out of their Spectrum remote control.

**Spectrum Remote Control User Guide

**

Spectrum Remote Control

Getting Started: Install Batteries

1. Apply pressure with your thumb and slide the battery door for removal. Show image of bottom of remote, indicating pressure point and slide direction
2. Insert 2 AA batteries. Match the + and – marks. Show illustration of batteries in place
3. Slide the battery door back into place. Show bottom of remote with battery door in place, include arrow for slide direction.

Other top spectrum manuals:

• Spectrum Remote Control User Guide
• Spectrum SR-002-R Remote Control User Guide
• Spectrum B08MQWF7G1 Wi-Fi Pods User Guide

Setup Your Remote for a Charter WorldBox

If you have a Charter WorldBox, the remote must be paired with the box. If you do NOT have a WorldBox, proceed to PROGRAMMING YOUR REMOTE FOR ANY OTHER CABLE BOX.

To Pair the Remote to the WorldBox

1. Ensure that your TV and WorldBox are both powered-on and that you can view the video feed from the WorldBox on your TV.
   Show image of STB and TV connected and on

2. To pair the remote, simply point the remote at the WorldBox and press the OK key. The Input key will begin blinking repeatedly.
   Show image of remote pointed at the TV, transmitting data

3. A confirmation message should appear on the TV screen. Follow the on screen instructions to program the remote control for your TV and/or audio equipment as needed.

To Un-Pair the Remote to the WorldBox

If you wish to use the remote with a different cable box, follow these steps to un-pair it with your WorldBox.

1. Press and hold MENU and Nav Down keys simultaneously until the INPUT key blinks twice. Show remote with MENU and Nav Down keys highlighted
2. Press 9-8-7 digit keys. The INPUT key will blink four times to confirm pairing has been disabled. Show remote digits with 9-8-7 highlighted in order.

Programming Your Remote for Any Other Cable Box

This section is for any cable box that is NOT a Charter WorldBox. If you have a WorldBox, refer to the section above for remote pairing, following the on- screen instructions for any other remote programming.

Setup Remote to Control Cable Box

Point your remote at your cable box and press MENU to test. If the cable box responds, skip this step and proceed to PROGAMMING YOUR REMOTE FOR TV AND AUDIO CONTROL.

1. If your cable box is branded Motorola, Arris, or Pace:

   • Press and hold MENU and the 2 digit key simultaneously until the INPUT key blinks twice.
     Show remote with MENU and 3 keys highlighted

2. If your cable box is branded Cisco, Scientific Atlanta, or Samsung:

   • Press and hold MENU and the 3 digit key simultaneously until the INPUT key blinks twice.
     Show remote with MENU and 3 keys highlighted

Programming Your Remote for TV and Audio Control

Setup for Popular TV Brands:
This step covers setup for the most common TV brands. If your brand is not listed, please proceed to SETUP USING DIRECT CODE ENTRY

1. Ensure that your TV is powered-on.
   Show TV with remote pointed at it.

2. Simultaneously press and hold MENU and OK keys on remote until the INPUT key blinks twice.
   Show remote with MENU and OK keys highlighted

3. Find your TV brand in the chart below and note the digit that relates to your TV brand. Press and hold down the digit key.

Digit

|

TV Brand

---|---

1

|

Insignia/Dynex

2

|

LG/Zenith

3

|

Panasonic

4

|

Philips/Magnavox

5

|

RCA/TCL

6

|

Samsung

7

|

Sharp

8

|

Sony

9|

Toshiba

10

|

Vizio

4. Release the digit key when the TV turns off. Setup is complete.
   Show remote pointed at TV, transmitting data and TV is off

NOTES: While holding the digit key, the remote will test for the working IR code, causing the INPUT key to flash each time it tests a new code.

Setup Using Direct Code Entry

This step covers setup for all TV and Audio brands. For faster setup, be sure to locate your device brand in the code list before beginning setup.

1. Ensure that your TV and/or audio device is powered-on.
   Show TV with remote pointed at it.

2. Simultaneously press and hold MENU and OK keys on remote until the INPUT key blinks twice.
   Show remote with MENU and OK keys highlighted

3. Enter the 1st code listed for your brand. The INPUT KEY will blink twice to confirm once complete.
   Show remote with digit keys highlighted

4. Test volume functions. If the device responds as expected, setup is complete. If not, repeat this process using the next code listed for your brand.
   Show remote controlling TV.

Assigning Volume Controls

The remote is set to default to control TV volume once the remote is programmed for a TV. If the remote is also set up to control an audio device, then volume controls will default to that audio device.
If you wish to change volume control settings from these defaults, perform the following steps:

1. Simultaneously press and hold MENU and OK keys on remote until the INPUT key blinks twice.
   Show remote with MENU and OK keys highlighted

2. Press the key below for the device that you wish to use for volume controls:

   • TV Icon = To lock volume controls to the TV, Press VOL +
   • Audio Icon = To lock volume controls to the audio device, Press
   • VOLCable Box Icon = To lock volume controls to the cable box, Press MUTE.

Troubleshooting

Problem:

|

Solution:

---|---

INPUT key blinks, but remote does not control my equipment.

|

Follow the programing process in this manual to set your remote up to control your home theater equipment.

I want to switch VOLUME CONTROLS from to control my TV or to my Audio Device.

|

Follow ASSIGNING VOLUME CONTROLS instructions in this document

The INPUT key does not light up on the remote when I press a key

|

Ensure that the batteries are functional and are inserted properly Replace the batteries with two new AA size batteries

My remote won’t pair with my Cable Box.

|

Ensure that you have a Charter WorldBox.
Ensure that the remote has a clear line of sight to the Cable Box when pairing.
Be sure to follow the on-screen instructions that appear when pairing.

Remote Key Chart

Show image of the whole remote control with lines pointing to each key or key group for the description below.

TV POWER

|

Used to turn on the TV

---|---

INPUT

|

Used to switch video inputs on your TV

ALL POWER

|

Used to turn on the TV and set-top box

VOLUME +/-

|

Used to change volume level on TV or Audio Device

MUTE

|

Used to mute volume on TV or STB

SEARCH

|

Used to search for TV, Movies, and other content

DVR

|

Used to list your recorded programs

PLAY/PAUSE

|

Used to play and pause current selected content

CH +/-

|

Used to cycle through channels

LAST

|

Used to jump to the previous tuned channel

GUIDE

|

Used to display the program guide

INFO

|

Used to display selected program info

NAVIGATION UP, DOWN, LEFT, RIGHT

|

Used to navigate on-screen content menus

OK

|

Used to select on-screen content

BACK

|

Used to jump to previous menu screen

EXIT

|

Used to exit the current displayed menu

OPTIONS

|

Used to select special options

MENU

|

Used to access main menu

REC

|

Used to record current selected content

DIGITS

|

Used to enter channel numbers

Declaration of Conformity

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by the turning of equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

The user is cautioned t that the changes and modification made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.

SPECIFICATION

TVs, cable boxes, and audio equipment
Battery Requirement| 2 AA batteries
Pairing| Needs to be paired with Charter WorldBox or other cable box
Programming| Step-by-step instructions provided for programming the remote for any device, including popular TV brands
Troubleshooting| Troubleshooting tips provided for common issues, such as unresponsive equipment or difficulty pairing the remote
Key Chart| Comprehensive key chart provided that outlines the function of each button on the remote
Declaration of Conformity| Includes a Declaration of Conformity that outlines the FCC regulations for this device

FAQs

How do you change battery?

The battery cover is on the back. The lower end of the remote

Do you have covers for this remote

Not to my knowledge, but there are a few items that you can drape over the arm of a couch or chairs. You just put them in them and its right next time you have them right there

Is this a universal remote? I need remote for Panasonis Blu-ray player.

While it is a universal remote I doubt you will be able to control your Panasonic blue ray player. You can definitely program it to control your TV volume and maybe a soundbar volume.

Can this remote be programmed for RF?

Yes, but the the manual with the remote doesn’t mention the procedure. I found the setting buried deep in Spectrum’s menu using the remote connected with its IR function out of the box: press the Menu button on the remote, then Settings & Support, Support, Remote Control, Pair New Remote, RF Pair Remote.

Is this the SR-002-R?

I can’t find the designation “SR-002-R” anywhere on the remote, but looking at the SR-002-R manual online, the controls are identical. The paper manual for this remote has the designation “URC1160”. FWIW, we’re using this replacement successfully with a Spectrum cable box without DVR, so I can’t vouch for that function.

The numbers on the bottom of the remote do not light up like the rest of the remote. Is the remote defective?

Yes, that remote is defective and has been since day 1. I got 3 new ones and they were so defective, I ordered one from amazon, and it was defective too. The manufacture should recall them or fix them.

Will this work on the 200?

No. Use the old one. There is also a back button on the old one.
The other fre

Are the buttons on this remote backlit?

Yes, the keys are illuminated

Is this remote control compatible with spectrum 201?

I’m a new Spectrum customer and I’m pretty sure I have the 201 box. I can confirm it on Monday when I get back home.

Need to turn off screen writing. How?

Ours is done by using the tv remote for use on the tv closed captioning. For use on spectrum system there is a few ways. Lower corner look for the c/c and click. Or menu until you find c/c and click. You tube has lots of videos to help.

How do I reprogram this remote??

You need the programming guide with the device codes ie. TV DVD AUDIO VIDEO RECEIVER.

Will it work with spectrum streaming services ?

It has worked with everything and so reasonably priced!

Can this remote program a Polk sound bar?

Not directly. We have our Polk Sound Bar connected to the LG television, and after programming this remote to control the TV, it can also control volume and mute for the sound bar. It’s a little wonky, in that we’ve got to turn the TV power on first, let it finish booting, then turn on the cable box, otherwise the TV gets confused and doesn’t forward sound to the sound bar, and instead tries to use the built-in speakers.

How do I pair my Spectrum Netremote with my Charter WorldBox?

Ensure that your TV and WorldBox are both powered-on and that you can view the video feed from the WorldBox on your TV. To pair the remote, simply point the remote at the WorldBox and press the OK key. The Input key will begin blinking repeatedly. A confirmation message should appear on the TV screen. Follow the on-screen instructions to program the remote control for your TV and/or audio equipment as needed.

How do I un-pair my Spectrum Netremote from my Charter WorldBox?

Press and hold MENU and Nav Down keys simultaneously until the INPUT key blinks twice. Then, press 9-8-7 digit keys. The INPUT key will blink four times to confirm pairing has been disabled.

How do I program my Spectrum Netremote for any other cable box?

Point your remote at your cable box and press MENU to test. If the cable box responds, skip this step and proceed to programming your remote for TV and audio control. If your cable box is branded Motorola, Arris, or Pace, press and hold MENU and the 2 digit key simultaneously until the INPUT key blinks twice. If your cable box is branded Cisco, Scientific Atlanta, or Samsung, press and hold MENU and the 3 digit key simultaneously until the INPUT key blinks twice.

How do I program my Spectrum Netremote for TV and audio control?

For setup of popular TV brands, simultaneously press and hold MENU and OK keys on remote until the INPUT key blinks twice. Find your TV brand in the chart provided in the user guide and note the digit that relates to your TV brand. Press and hold down the digit key. Release the digit key when the TV turns off. For setup of all TV and audio brands using direct code entry, enter the 1st code listed for your brand. The INPUT KEY will blink twice to confirm once complete. Test volume functions. If the device responds as expected, setup is complete

How do I troubleshoot if the INPUT key blinks, but the remote does not control my equipment?

Follow the programming process in the user guide to set your remote up to control your home theater equipment.

How do I troubleshoot if my remote won’t pair with my Cable Box?

Ensure that you have a Charter WorldBox. Ensure that the remote has a clear line of sight to the Cable Box when pairing. Be sure to follow the on-screen instructions that appear when pairing.

How do I change volume controls from my TV to my Audio Device?

Simultaneously press and hold MENU and OK keys on remote until the INPUT key blinks twice. Press the key below for the device that you wish to use for volume controls: TV Icon = To lock volume controls to the TV, Press VOL +; Audio Icon = To lock volume controls to the audio device, Press VOL; Cable Box Icon = To lock volume controls to the cable box, Press MUTE.

Spectrum Netremote_ User Guide for Spectrum Remote Control

VIDEO

Spectrum Remote Control User Guide – Download [optimized]
Spectrum Remote Control User Guide – Download

Spectrum Remote Control User Guide
Click to Read More Spectrum Manuals

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>