TBFZ-2701 TBFPBR-2701 TRINITY EXPANDABLE CLOSET organizer Owner’s Manual
- June 7, 2024
- TBFZ-2701 TBFPBR-2701
Table of Contents
OWNER’S MANUAL
TRINITY EXPANDABLE CLOSET ORGANIZER Model # TBFZ-2701 / TBFPBR-2701
I mportant / Important / Importante
FOR QUICK & EASY 3D ASSEMBLY INSTRUCTIONS
Intelligent Instraction
Directives intelligentes
Instrucciones Inteligentes
PARTS LIST
Your TRINITY Expandable Closet Organizer should include the following parts.
Please inspect box contents to ensure you have received all components.
If you are missing any parts, need assistance with assembly or have questions,
please contact TRINITY Customer Service: 800.985.5506 or
customerservice@trinityii.com. Parts
can also be requested online via “Contact Us” section at
www.trinityii.com. You will NOT need additional
tools for assembly.
ASSEMBLY INSTRUCTIONS
STEP 1
Screw each LEVELER (K) into the bottom of each BOTTOM POLE (F). Turn clockwise
to screw in place.
Starting from the bottom of the BOTTOM POLE (F), attach two pieces of black
plastic SLIP SLEEVES (J) on either side of the pole in the desired groove.
Slide the plastic SLIP SLEEVES (J) down until they click into position. Repeat
for the other three poles.
Tip: Use the grooves on the pole as a guide to ensure a level shelf height.
STEP 2
With the SMALL SHELF (A) on its side, slide each of the BOTTOM POLES (F)
through the shelf collars.
Stand the unit upright and push down on the SMALL SHELF (A). Using a rubber
mallet to lightly hammer the SMALL SHELF (A) down over the collars is helpful
but not necessary.
Note : For stability, the lowest SMALL SHELF (A) should be installed no
higher than the 3rd indentation from the bottom of the BOTTOM POLES (F).
STEP 3
Attaching black plastic SLIP SLEEVES (J) onto the poles in the desired
grooves, slide the 2nd SMALL SHELF (A) from the top of the BOTTOM POLES (F)
onto the pairs of black plastic SLIP SLEEVES (J).
STEP 4
Screw the CONNECTORS (L) into the top of the BOTTOM POLES (F), connect the
four MIDDLE POLES (E) and the four BOTTOM POLES (F) with the CONNECTORS (L).
STEP 5
Repeat STEP 3 for assembly of the 3rd SMALL SHELF (A)
Screw the CONNECTORS (L) into the top of the MIDDLE POLES (E), connect the
four TOP POLES (D) and the four MIDDLE POLES (E) with the CONNECTORS (L).
Repeat STEP 3 for assembly of the 4th SMALL SHELF (A)
STEP 6
Repeat STEP 3 for assembly of the TOP SHELF (B)
The first tower is ready. Repeat STEP 1 through STEP 6 to assemble the second
tower.
Note : For stability, the TOP SHELF (B) should be installed no lower than
the 3 rd indentation from the top.
STEP 7
Top: Hang the HANGING BRACKET (H) over the wire strand in the middle of the
TOP SHELF (B). Do the same for the other side.
Bottom: Hang the HANGING BRACKET (H) over the lip of SMALL SHELF (A). Do the
same for the other side. Fasten HANGING SCREW (I) through HANGING BRACKET (H)
to HANGING ROD (G). Do this for both HANGING RODS (G).
Note : The organizer is able to fit closet widths ranging from 56” to
78”. Please place towers in position before expanding the HANGING ROD (G) and
attach to HANGING BRACKET (H) with HANGING SCREW (I).
STEP 8
Place CLOSET ORGANIZER by the wall, drill 1 hole on each side of the wall at
the same level of TOP SHELF (B) where ANTI-TIPPING KIT (M) is desired to be
placed.
Fasten ANTI-TIPPING KIT (M) to the wall and cable loop through TOP SHELF (B)
as the image shows, and close up the cable loop, connecting CLOSET ORGANIZER
to the wall via ANTITIPPING KIT (M).
Place each BAMBOO BOARD (C) onto each SMALL SHELF (A) as shown.
SERVICE PARTS LIST – TBFPBR-2701 Bronze Color
TRINITY Customer Service provides the following replacement parts:
Part Numbe
|
Description
---|---
1. XBK-01-012-2543| Slip Sleeve
2. PBR-04-006-2750| Top Pole
3. ZSV-01-013-2523| Pole Connector
4. PBR-04-007-2800| Middle Pole
5. PBR-03-007-1414| Small Shelf
6. PBR-04-008-2700| Bottom Pole
7. XBK-98-003-2538| Feet Leveler
8. ONA-20-003-1313| Bamboo Board
9. PBR-13-008-2700| Hanging Rod
10. XBK-01-024-0627| Hanging Screw
11. PBR-02-010-0001| Hanging Bracket
12. PBR-03-024-1428| Top Shelf
13. XSV-02-011-0007| Anti-tipping kit
SERVICE PARTS LIST – TBFZ-2701 Chrome Color
TRINITY Customer Service provides the following replacement parts:
Part Number Description
- XBK-01-011-2543 Slip Sleeve
- ZSV-04-006-2750 Top Pole
- ZSV-01-013-2523 Pole Connector
- ZSV-04-007-2800 Middle Pole
- ZSV-03-007-1414 Small Shelf
- ZSV-04-008-2700 Bottom Pole
- XBK-98-003-2538 Feet Leveler
- ONA-20-003-1313 Bamboo Board
- ZSV-13-008-2700 Hanging Rod
- XBK-01-024-0627 Hanging Screw
- ZSV-02-010-0001 Hanging Bracket
- ZSV-03-024-1428 Top Shelf
- XSV-02-011-0007 Anti-tipping kit
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>