thanos Rodent Repellent User Manual
- June 7, 2024
- thanos
Table of Contents
Rodent Repellent
User Manual
MODEL: AR28
Dear customers, thank you very much for purchasing our products. Please read this product manual carefully before using this product. If you have any questions about your order or this product, please feel free to contact us.
INTRODUCTION:
Rodent Repellent can emit changing ultrasound at frequency 18kHz-36kHz, barely perceptible to the human ear and prevents the animals from getting adapted to the noise. Also emit bright flashes to keep pest rodent or marten away from your properties or vehicles.
The rodent repellent includes a vibration sensor, which will switch the device
on when the vehicle is stationary. The device will go to standby when
detecting a vibration by starting the vehicles.
It supports dry batteries, rechargeable batteries and connects to DC power or
vehicle power by included cables.
PRODUCT APPEARANCE:
- Blinding light
- Ultrasonic speaker
- Red/green indicator
- Power On/Off
- 4*AA batteries (not included)
- Power input: DC 5~12V
- 1*DC to USB cable
- 1*cable to vehicle power
- 4*cable ties
SPECIFICATION:
- Power input: DC 5~12V
- Working current: 5mA
- Power consumption: 0.1W
- Ultrasound frequency: 18-36kHz
- Power supply: 4*AA batteries, DC 5-12V vehicle power or adaptor
- Operating temperature range: -25~+80°C
- Sound pressure: 110dB
INSTALLATION:
Note: Both B and C can work without batteries; or support rechargeable
batteries to get charged.
A). Open the battery cover and put 4*AA batteries (not included), pay
attention to the positive and negative charges.
B). Or connect to DC 5-12V adaptor (not included) with DC to USB cable.
C). Or connect to DC 5-12V
vehicle power by included cable, link the two connectors with the vehicle
power, black lead/cathode(-), red lead/anode(+).
2. Fix the device by included cable ties in the vehicle engine compartment,
car trunk, garage, living room, etc.
3. Press power button to turn on the device, red indicator and blinding light
starts to flash and it emits sound at 4kHz to indicate the device can work
normally to repel invading pests.
4. Indicator and Work Modes: Working 10s every 100s
A. Working Mode(no vibration detected):
B. Standby (vibration detected):
Stop
Red light flash every 2S
Restart after the last vibration detected for 120 seconds.
ATTENTION:
- The included vibration sensor makes noise when shaking the device, it’s in normal condition.
- Since there is no vibration switch inside, the vibration caused by pressing the switch too hard when it is turned on may cause the device to standby.
- Working temperature: -25~+80°C, the device will be deformed when exceeding the range.
- Please DON’T fix the device on the engine’s surface for its high temperature.
- Leave spaces between the device and the car hood, avoiding it transfer high temperature to the device.
- When used in the engine compartment: before using the repellent we recommend having the engine washed at an auto shop. This will remove all odors and smells that might attract the marten and/or tell it that this has been its former home.
- Improper installation may cause a short circuit or electric shock. We recommend installing it in a service station or auto supply store where the local government authorized to avoid the wrong installation.
- If the device fails to work, please check batteries inside first, then press the power button to restart.
- Then the most important thing is that contact us ASAP to help you deal with the problems.
DISPOSE:
Dispose of all parts appropriately and safely and in compliance with your national regulations and local environmental standards.
WARRANTY:
All of thanos® products support a 60-day refund and a 12-month free
replacement. If you have any questions about your order or product, please
feel free to contact us. We will do our best to help you
support@thanosgift.com
www.x-pest.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>