DS18 Nxl-X8tpneo Wakeboard Pod Tower Speakers Specifications

June 7, 2024
DS18

Logo

Nxl-X8tpneo Wakeboard Pod Tower Speakers

product

Specifications

General Specifications

Nominal Diameter…………..8”
Nominal Impedance……….4ohm
RMS Power Handling………180W
MAX Power Handling………550W
Sensitivity (1w/1m)………….95dB
Frequency Response………60Hz-21Khz

Body / Features

Enclosure Material………….Injection PC+ABS
Marine Grade Type………….IP65 + UV Stable
RGB LED…………………………Integrated LED-RGB Speaker Lighting,Integrated LED-RGB Acrylic Ring Lighting, 6 Core Wires for Lighting and Speaker
Grill Type………………………… ABS+316 Stainless Metal Mesh
Pair………………………………… Yes
Clamps…………………………… Die-Cast adjustable (1″ ~ 2″)
360 Degree Rotation Mounting
Buried Wire or Open Wire Mounting Optional,
Included NBR Pad And Stainless Hardware
(Screws,Stop Washers,Hexagon wrench,
Safety Rope, Screw fastening Glue)
Front Logo……………………… Yes, Can be Rotated For Correct Angle Display
Finish……………………………..  Yes, Can be Rotated For Correct Angle DisplaySpecification

Packaging Includes

  • 1 Pair 8” Wakeboard Pod Tower Speaker
  • 1 Piece 6 mm Hex wrench Chromed
  • 1 Piece 4 mm Hex wrench Chromed
  • 1 Pair NBR Pad For 1” to 3” tube adjust
  • 1 Pair Stainless Safety Rope
  • 1 Pcs Screw Fastening Glue

If you have an LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:Installation

To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:

  • Black wire “BK” Connected to Battery Positive(+) 12V
  • White Color Light “R”; “B” and “G” Connected to Battery Negative (-)
  • Green Color Light “G” Connected to Battery Negative(-)
  • Red Color Light “R” Connected to Battery Negative(-)
  • Blue Color Light “B” Connected to Battery Negative(-)
  • Purple Color Light “R” and “B” Connected to Battery Negative(-)
  • Yellow Color Light “R” and “G” Connected to Battery Negative(-)
  • Cyan Color Light “B” and “G” Connected to Battery Negative (-)

Installation 2

Beginning Mounted

Cut the length of rubber pad and wires outlet according to the diameter of installation pipe.Installation 3 Installation
4

Wrap the rubber pad around the pipe and align wire out hole According to the diagram.Installation 7

Push the wire into the tube, press on the rubber pad,and lock the the top clamp .

Take down the safety rope and hang it on the pipe, lock the screw gasket safety rope lifting ring on the clamp base, and apply screw fastening glue on the screw before locking.Installation 9

During the mounting process you should have located the spot to drill your tower bar for the 6 conductor wire (Speaker and RGB lightning wiring) insertion. Or NOT (see Tie-wrap solution below)Installation
11

Remove Wire NBR Plug and Slide the wire threw the hole Snake the wire down to the bottom of the tower tube in a location that the wires can be attached to the audio (And lighting) system. Solder or butt connect the speaker wire coming from the tower to the speaker wire to the system. Then heat-shrink it for added protection from water / moisture.

Installation 12

FLAT MOUNTED/TUBE MOUNTEDInstallation 13

DIMENSIONS

Dimension

Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DS18 User Manuals

Related Manuals