NEXTECH 2K GPS Dash Camera Rear Camera User Manual
- June 7, 2024
- Nextech
Table of Contents
2K GPS Dash Camera
with Rear Camera
QV3849
User Manual
ABOUT THE PRODUCT
This product is designed to provide high definition recording of your trips
for security and evidence in the case of an incident. Being portable, this
convenient and durable multi-vehicle driving recorder can be used in a variety
of situations for video recording.
This product is not guaranteed to record ALL events. Use this product only for
reference when investigating incidents or road accidents. The device may not
properly record accidents, it only operated by a range of impact. Ensure
completely turned on the recorder, then video recording and event recording
will available. The Dash Cam is not designed to be used without accessory
power.
Nextech is not responsible for any loss caused by an accident, nor is it
responsible for providing any support regarding the outcome of an accident.
PRODUCT STRUCTURE AND INSTRUCTIONS
1.
Charging port on bracket
2. Camera Lens
3. LCD Display
4. Speaker
5. SD Card Slot
6. Charging Port
7. 3M sticker
8. AV/IN Hole
9. Microphone
10. Reset
11. Menu /Back
12. Left
13. OK
14. Locked Video/ Right
15. Power/Mode
16. LED Indicator
MENU/Back
Press button to enter Menu selection during standby mode, to press the back
button to back to the video standby mode. Long press the menu button to switch
between front/rear camera.
Left
Press button to move to the last selection during menu setting or file
selection. Press the left button to turn on /off the voice recording during
video standby or video recording mode.
OK
Press button to confirm current selection. In standby mode, press OK to start
to record video.
Emergency Recording/Forward
Press button to enter emergency recording mode during video recording, the
video will not be covered by loop recordings, and the Lock icon will be shown
in the right corner of LCD display; To press the Forward button to move to the
next step during menu setting or file selection.
POWER/MODE
Quick press button to start the camera.
The camera will start recording automatically if SD-card has already been
installed; Long press the power button for 2 seconds to turn off the device
Short press the Mode button to enter into camera/ video recording/ video
playback in standby mode.
PRODUCT FUNCTIONS
Video Recording
Insert SD card into the product and get power from the car charger, the
dashcam will start recording automatically, click OK button to stop recording.
Video playback
Press the Mode button to review photos, Press Menu to select emergency or loop
recording video and press the back button to review. G-sensor The machine has
a built-in G-sensor, it will lock the video automatically during a vehicle
collision, the locked video won’t be overwritten, and the locked icon shows in
the right corner of the LCD display screen.
Parking monitor
In shutdown mode, when the dashcam detects a vibration, it will start to video
record and will then lock the current file, It will then shut down
automatically after 30 seconds if no operation is detected.
Loop recording
Overwrites existing files and records in either 1/3/5 minutes blocks.
Record audio
The close or open audio recording in the video file.
GPS Location
Install the GPS Media player on your computer, so you can review GPS location
as shown in the top right-hand corner and the speed is also shown at the
bottom.
Rear Camera
Connect the camera with the included rear camera by inserting the plug into
AV/IN on the device. You will find the rear camera image shows on the right
corner of the LCD display after 3–5 seconds, then long-press the Menu button
to switch the front/ rear videos.
When the reversing camera is connected to the Dash Cam and it is powered on,
the reversing camera will be displayed in the top right corner of the LCD
screen after 3–5 seconds. When recording, it will save both videos from the
front Dash Camera and Reversing Camera inside the microSD Card. When you put
your vehicle in reverse, the reverse camera will be displayed on the Dash Cam
with reversing lines (A short cable on the rear camera needs to be wired to
the reverse light on your car).
PRODUCT SPECIFICATION
| Display: | 3.0” LCD |
|---|
Front Camera:
- Video Resolution:
- Image Resolution:
- Frame Rate:
- Lens Angle:
| Up to 1296p
3MP
30fps
140°
Rear Camera:
- Video Resolution:
- Lens Angle:
- Waterproof Rating:
- Working Voltage:
- Cable length:
| 640 x 480
60°
IP65
5VDC
5.5m
Video Compression:| H.264
Video File Format:| MOV
Image File Format:| JPG
Storage:| Up to 64GB microSD
Battery:| Li-ion 3.7V, 300mAh
Power:| 5VDC @ 1.5A
Car Charger Voltage Input:| 12-36VDC
Dimensions:| 85(W) x 61(H) x 32(D)mm (Excluding Mount)
WARNING
- Do not expose the product to direct sunlight or intense light. Such damages are not covered by the warranty.
- Frequently check the product for the proper installation position.The impact caused by extreme road conditions may alter the installation position. Ensure that the product is positioned as instructed in this guide.
- Do not use chemical cleaners or solvents to clean the product.
- Do not disassemble the product or subject the product to impact.
- This device is designed to record video while the vehicle is in operation. The quality of the video might be affected by weather conditions and the road environment, such as whether it is day or night, the presence of street lighting, entering/exiting tunnels, and the surrounding temperature.
- This device is intended to be used inside the vehicle only.
DRIVING AND PRODUCT OPERATION
- Do not operate the product while driving a vehicle. Distraction while driving may cause accidents and result in injury or death.
- Install the product in places where the driver’s view is not obstructed. Obstruction of the driver’s vision may cause accidents and result in injury or death. Check with your state and municipal laws before mounting the product to the windshield.
POWER SUPPLY
-
Connect the car adapter’s mini USB plug to the mini USB port in the suction cup. Connect the cigarette lighter adapter plug to the vehicle’s cigarette lighter port. It is suggested to wire the cable along with your windscreen.
-
In certain models of cars, the cigarette lighter keeps providing power even when the engine is off. Be sure to remove the car charger or disconnect the device when leaving the vehicle to prevent draining the vehicle battery. Check your vehicle’s owner’s manual to determine if this applies to your vehicle
INSTALLATION
- Fix the windscreen charging mount to the top of your windscreen, it is suggested towards the middle position of your windscreen.
- Peel off the adhesive sticker located on the top of the windscreen charging mount once you have the desired location and stick on your windscreen.
- Attach the dash camera to the windscreen charging mount by the magnet and adjust to the correct position facing forward.
Note: It is recommended to place the dash camera behind the rear vision mirror to prevent the camera from obstructing your view while driving.
REAR CAMERA
With the help of a rear camera, you can get a high-resolution image behind
your car for safe parking or recording while driving. Modern double recording
technology allows saving recordings both in front and behind the car for
fixing any unforeseen situation.
Rear Camera Installation
There are two options of using a rear camera.
Option 1.
DVR camera for getting view behind the car. Install the camera on the rear
window with a sticker, put the wire through the cabin, connect the wire to the
rear camera port.
Option 2.
Combination of DVR camera and rear camera for the back view when parking.
Install the camera on the rear window inside the car, or outside on the
license plate frame. In this case, it is required to apply +12 V when driving
backward. This will allow the device to automatically switch the image from
the front to the rear camera in the parking mode. Note: It is strongly
recommended that works on installing the camera and connecting +12 V should be
done by qualified personnel with the necessary skills. Cable routing may
require special tools or attachments. Make sure these works are safe.
Distributed by:
TechBrands by Electus Distribution Pty. Ltd.
320 Victoria Rd, Rydalmere
NSW 2116 Australia
Ph: 1300 738 555
Int’l: +61 2 8832 3200
Fax: 1300 738 500
www.techbrands.com
Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>