Swiss Madison – well made forever Wall-Hung Toilet Installation Guide

June 7, 2024
Swiss Madison - well made forever

Swiss Madison® Wall-Hung Toilet Installation Instructions

Swiss Madison® Wall-Hung Toilet

@SwissMadison

WellMadeForever

www.swissmadison.com | 1-434-623-4766 | info@swissmadison.com

PRIOR TO INSTALLATION

  • Inspect toilet to ensure no damages have occurred while in shipping.
  • Observe all plumbing and building codes in accordance with your state and local requirements.
  • All dimensions are nominal! Be sure to measure your toilet prior to installation.
  • The step-by-step guidelines in the installation instructions are a general reference. Should there be any discrepancies, Swiss Madison cannot be held liable. It is recommended to install all Swiss Madison products by hiring a licensed professional.
  • Read installation and maintenance instructions thoroughly before installing. Be sure to use proper tools and always wear proper personal safety accessories for your protection.
  • Two people are recommended to handle and install this product as it is fragile.

If you have any questions or concerns please contact us:
1-434-623-4766
info@swissmadison.com

SUGGESTED TOOLS & MATERIALS

SUGGESTED TOOLS & MATERIALS

REQUIRED PARTS

REQUIRED PARTS

  1. Install Tank Carrier System

    • Before toilet bowl installation, a wood frame and commercial or residential tank system is required.
    • Install according to manufacturer’s instructions.
  2. Dry Fit Outlet Pipe and Inlet Pipe

    • Fully insert straight tube into cistern flushing outlet then connect pipe into discharge outlet.
    • Draw lines to mark the finished wall location on each pipe as pictured below.
      diagram, engineering drawingInstallation Figure 1
  3. Determine Pipe Size

    • Apply lubricant on rubber washers of straight tube and connecting pipe, then insert into holes.
    • Draw lines on pipes as pictured below.
      Installation Figure 2
  4. Cut Pipes

    • Measure the distance between both marked lines on pipe. Take measured distance, deduct from bald end of pipe and cut pipes as shown below.
    • After cutting, take a file and remove all burrs. Try and bevel pipe edge.
      L1: The distance between the two lines on the straight tube.
      L2: The distance between the two lines on the connecting pipe.
      Installation Figure 3
  5. Mount Toilet Bowl

    • Apply lubricant to the joint surface on straight tube and connecting pipe.
    • Mount the toilet bowl to the wall.
      Installation Figure 4
  6. Level and Attach Bowl

    • Attach bowl using the washers and bolts, make sure the bowl is level, then cover with included cap.
    • Fill any gaps with cement or sealant.
      Installation Figure 5

TOILET SEAT INSTALLATION

  1. Dissassemble

    • Disassemble the cover cap and the hinge.
      TOILET SEAT INSTALLATION FIGURE 1
  2. Construct Hinges

    • Insert screw and nut into the hole on the hinge.
    • Attach blind hole screw fixing to the bottom of screw.
      TOILET SEAT INSTALLATION FIGURE 2
  3. Attach Hinges

    • Insert hinges with blind hole screw fixings attached into holes on toilet bowl.
    • Lightly tighten hinges with a screwdriver too allow for later adjustment.
      TOILET SEAT INSTALLATION FIGURE 3
  4. Adjust and Cover Hinges

    • Be sure the hinge is all the way forward for proper seat fitting.
    • Place the covers onto the hinges.
      TOILET SEAT INSTALLATION FIGURE 4
  5. Adjust and Attach Seat

    • Align seat to the hinges then firmly tighten the hinges.
    • Attach seat to the secure hinges.
    • Adjust seat to align to the bowl.
      TOILET SEAT INSTALLATION FIGURE 5

TOILET SEAT USAGE

  • To remove, push middle button until you hear a “click”, then pull straight up.
  • To re-install, align hinge posts with reference marks on seat, then push down until your hear a “click”.

TOILET SEAT USAGE

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals