Husqvarna Style 910 Chainsaw User Manual

: June 8, 2024
: Husqvarna

Table of Contents

Husqvarna Style 910 Chainsaw
Introduction
Safety
Maintenance
Compliance and approvals
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Husqvarna Style 910 Chainsaw

Introduction

Product Description
This product is an item of personal protective equipment (PPE). The products are intended to be used during operation with a chainsaw. The products have different safety classes classified by the material used in the protective material. The applicable safety class is marked on the label of the product. The protective material can be made out of different materials such as fiber material that can tear into the chain. The higher the class the better the protective function. Use the type of personal protective equipment that is correct for the type of work and the work environment. Ask your dealer for help in choosing the right product. (Fig. 2) The products have different designs and sizes. Make sure to use the correct size.

Definition of acronyms on the label (Fig. 1)

ST| Safety toecap 200 J (falling objects) 15 kN (crush injuries)
CH| Closed heel
AN| Antistatic 100 kΩ-100 MΩ
Definition of acronyms on the label (Fig. 1)

E| Energy absorption heel 20 J
WRU| Water-repellent upper part
POS| Patterned outer sole
P1| Penetration resistance (nails etc.)
Definition of acronyms on the label

Safety

Safety definitions
Warnings, cautions, and notes are used to point out especially important parts of the manual.

WARNING: Used if there is a risk of injury or death for the operator or bystanders if the instructions in the manual are not obeyed.
CAUTION: Used if there is a risk of damage to the product, other materials, or the adjacent area if the instructions in the manual are not obeyed.
Note: Used to give more information that is necessary in a given situation.

General safety instructions

WARNING: Read the Operator’s Manual carefully and make sure you understand the instructions before you use the product.
WARNING: No PPE can offer full protection against injury. PPE will decrease the degree of injury if an accident does occur.

Use of this product does not decrease the need for the safe operation of the chainsaw.
Carefully read all safety instructions applicable to your chainsaw.
When the product is new, the soles can be slippery before the outer layer becomes rugged. Be careful when you wear new safety boots.

The penetration resistance of this footwear has been measured in the laboratory using a truncated nail of diameter 4,5 mm and a force of 1 100 N. Higher forces of nails of smaller diameters will increase the risk of penetration occurring. In such circumstances, alternative preventative measures should be considered.

Do not use non-approved accessories on the product. Accessories can decrease the protective capabilities.
Make sure that the saw protection of the protective clothes overlaps the saw protection of the safety boot.
For best performance and safety, do maintenance on the product regularly. Refer to To do maintenance on the product on page 4.
Clean the product immediately in case it has been subjected to petrol, oil, grease, or other flammable materials. Fire hazard!
Make sure that the product is not damaged and there are no other defects, such as cracks. The product should be scrapped and not used again if the protective material has been damaged, incorrectly cleaned, or altered from its original shape. The protective qualities may be reduced in these cases.
Keep the product away from sharp objects, acids, oils, solvents, fuels, and animal droppings.
The heat resistance of the outsole (PU) is 120°C.
The product is supplied and tested with insoles. If the insole is to be replaced, always use the original spare parts.
If you feel uncertain after reading these instructions, speak to your Husqvarna dealer before continuing.

Maintenance

To do maintenance on the product

The service life of the product varies with the type of use. The service life depends fully on the condition of the product. To achieve maximum service life, the product must be maintained and kept in storage correctly.
Clean the product with a damp cloth or sponge. Do not use polishing or corroding cleaning agents.
When the product is wet, air dry slowly and away from heat sources such as radiators or direct sunlight.
Impregnate the safety shoe regularly. Use wax or silicone-based shoe care products or dubbin.
In the event of a repair being carried out to the outer material, do not sew into the protective material since this can reduce the protective qualities. The adhesive must not be used when carrying out repairs as it may affect the protective material and decrease its protective qualities.
Store the product on a level surface, standing up in a dark and dry area.

Disposal

Obey national regulations.
Use the local recycling system.

Service life of the product
The service life of the product varies with the type of use. In professional logging, the maximum service life of the product is 1 year. The maximum service life of the product is 5 years. Maximum service life can only be achieved if the product is used occasionally and non-professionally. To achieve maximum service life, the product must be kept in storage correctly. The product must be discarded after a maximum of 5 years of use. The actual service life depends fully on the condition of the product. Extreme conditions during operation can shorten the service life to a single use only. If the product is damaged before its first use, for example during transportation, it must be discarded immediately and not used.

CAUTION: Dispose the product and do not use it again if the product:

has been damaged.
has been washed incorrectly.
has been altered from its original shape.

Compliance and approvals

These products Style 910, Style 910A, Style 930, Style 931, Style, 932, Style 933, Style 934, and Style 940 conforms to the applicable EU regulations and comply with basic requirements and standards:

EU regulation 2016/425
EN ISO 17249:2013

CE Marking
The notified body responsible for type examination and carrying out annual Module C2 assessment of products covered by this user information following EU Regulation 2016/425 is SMP Svensk Maskinprovning AB, Box 4053, SE-904 03 Umeå, Sweden. Notified Body Number 0404, as shown next to the CE mark. The full text of the EU Declaration of Conformity is available at the following internet address: www.husqvarna.com; search for the product. Responsible manufacturer: Husqvarna AB, Drottninggatan 2, SE-561 82 Huskvarna, Sweden, tel:+46-36-146500.