SOZULAMP Illuminated 3-Way Light Switch Owner’s Manual
- June 7, 2024
- SOZULAMP
Table of Contents
Illuminated 3-Way Light Switch
Owner’s Manual
https://www.amazon.com/sozulamp
Instructions
WARNING
Failure to turn OFF electrical power at the service panel prior to removing/installing the Switch can result in electrical shock, fires, and/or death.
CAUTION: Please read all instructions and warnings before installing.
- Failure to follow these instructions can cause electrical shock, death or permanent injury.
- Do not work on live electricity.
- To be installed and/or used in accordance with appropriate electrical codes and regulations.
- Use the Switch only with copper or copper clad wire. Do not use it with aluminum wire.
- The Switch is for dry indoor locaion use only.
- The Switch is standard 3-Way and decor rocker switches with screw terminals.
- Recommended minimum wall box depth is 2-1/2″.
- If you are unsure about any part of these instructions, consult a qualfied elecrician.
Tools needed to install your switch:
Phillips Screwdriver Flathead Screwdriver
Voltage Detector Wire Cutter / Stripper
-1-
Specification:
3-Way Night Light Wall Switch
LED Power: 0.1W
LED Color : Warm white(3000K), Cool white(6000K)
Ground: U-Grounding screw
Amperage: 15Amp
Voltage: 120/277VAC.
HP Rating: 1/2HP-120V, 2HP -240V-277V
Max. Amp: 12Amp
Termination: Quick-wire Push-In & Side wired
Material: Thermoplastic
Body Material: Thermoplastic
Strap Material: Steel
Features Diagram:
CAUTION: Power lower than 9 wattage Locator Light Bulbs may flicker or illuminate when used with the Night Light Switch. If this is a concern, the light bulb can be changed for power more than 9 wattage.
**** -2-
Troubleshooting
WARNING
Failure to turn OFF electrical power at the service panel prior to removing/installing the Switch can result in electrical shock, fires, and/or death.
Having difficulties? Here are some tips that might help. Your Switch was individually tested and worked great when it was shipped. It is very unlikely that the Switch itself is malfunctioning. We will walk you through some issues that you might encounter.
QUICK OVERVIEW OF POSSIBLE INSTALLATION ISSUES
ISSUE
|
TROUBLESHOOTING
---|---
Locator Light Bulbs does not turn on| Circuit breaker controlling the
switch has been turned on.
Fuse has installed or fuse has tripped.
Make sure the wire connections in the wall box are secure.
Switch turn on.
Light bulbs are burned out.
Light bulbs neutral connection is not wired.
LED Night Light does not turn on| Make sure Locator Light Bulbs can turn
on.
The LED Night Light only illuminates when area is dark see “Test LED Night
Light” on Page 6.
Light bulbs must turn off, When the light bulbs turn on, the night light will
not work.
CAUTION
Power of Locator Light Bulbs must more than 9 wattage. If lower than 9 wattage the Locator Light Bulbs may flicker or illuminate.
-3-
Installation
Installing Switch is easy, but makes sure that you:
- Understand basic wiring principles and techniques.
- Can interpret wiring diagrams
- Have circuit wiring experience
- Are prepared to take a few minutes to test your work, making sure that you have wired the switch correctly.
If you do not fully understand these instructions, you should seek the assistance of a qualified electrician.
Step 1 Turn Off Power
Step 2 Preparing and connecting wires:
This Switch can be wired using side wire terminal screws or through back wire openings. Choose appropriate wire stripping specifications accordingly.
Strip Gage
(measure bare wire here or use gage on back of the Switch)
Side Wire Connection
Side wire terminals accept #14
AWG solid wire copper only.
Back Wire (either hole may be used)
Back wire openings use #14-12
AWG solid wire copper only.
Make sure that the ends of the wires from the wall box are straight (cut if
necessary)
-4-
Step 3 Wiring Diagram
- 3 Way Switch Wiring Diagram
- Single Pole Switch Wiring Diagram
Mode 1 Mode 2
-5-
Step 4 Testing switch prior to mounting in wall box:
- Position all wires to provide room in wall box for device.
- Ensure that the word “Bottom” is facing down on device.
- Partially screw in mounting screws in wall box holes.
Step 5 Place wall plate: (Wall plate sold separately)
Place wall plate over the switch and secure with screws.
Restore power at circuit breaker or fuse.
Turn on the Locator Light Bulbs, If it does not turn on, refer to
troubleshooting section.
Step 6 Test LED (Locator light bulbs must turn off)
Auto turns LED’S off when the light sensor is exposed to light
Darken the room or place finger (palm) on light sensor
Auto turns LED’S on when the area around light sensor is dark
-6-
PRODUCT LIMITED ONE-YEAR WARRANTY
What this Limited Warranty Covers and For How Lon g
Warrants that the Product accompanied by this limited warranty is free from
manufacturing defects in materials and workmanship for a period of one (1)
year from the date of original purchase, as shown on your invoice or sales
receipt. This warranty extends only to the original consumer purchaser of the
product from an authorized reseller.
Disclaimer of Implied Warranties Beyond the Limited Warranty Period
The limited warranty period of one (1) year also applies to any implied
warranties that may exist under applicable law, including the implied
warranties of merchantability and fitness for a particular purpose. There are
no warranties that extend beyond the description on the face hereof. Some
states do not allow limitations on how long an implied warranty lasts, so the
above limitation may not apply to you.
What this Limited Warranty does not Cover
This limited warranty does not apply to defects resulting from (1)
overloading, misuse, abuse, alteration, accident, neglect, improper
maintenance or handling, or normal wear and tear; (2) improper installation;
(3) installation in an improper environment; and (4) any use that is not under
normal operating conditions or not in accordance with any product packaging,
warmings, or instructions for use.
What we will do
If you believe the product is defective, please return it to us in the manner
described below within the limited warranty period of one (1) year from the
date of purchase. If we determine there is a defect covered by this limited
warranty, we will, at its option, repair, replace the product, or refund your
purchase price. This limited warranty extends to repaired and replacement
products and components only through the end of the original limited warranty
period.
Limitations of Remedies under this Limited Warranty
The remedies provided herein are the exclusive remedies under this limited
warranty, whether based on contract, tort or otherwise. In no event will us or
any of its retailers, dealers, distributors or resellers be liable for
incidental, indirect, special or consequential damages relating to the product
(including any repaired or replacement product or component), its use, or its
installation, including without limitation damage to, or loss of use of, any
equipment, lost sales or profits or delay or failure to perform this warranty
obligation. Some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion may not apply
to you.
How State Law Applies
This limited warranty gives you specific legal rights, and you may also have
other rights which vary from State to State.
What You Must do to Get Coverage Under this Limited Warranty
To make a claim under this limited warranty you must first contact us within
the limited warranty period. You must provide proof of purchase in the form of
your original sales receipt in order to obtain limited warranty coverage. We
will perform the warranty obligations, if any, within 60 days of the Owner’s
submission of the warranty claim.
-7-
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>