eufy Wire-Free Hd Security Camera User Guide

June 7, 2024
Eufy

eufy - logo

SECURITY

QUICK
START GUIDE
eufyCam 2 Pro
WIRE-FREE HD SECURITY CAMERA

eufy Wire-Free Hd Security Camera - 02

Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other  countries. All other trademarks are the property of their respective owners.

51005002323 V01

WHAT’S INCLUDED

For eufyCam 2 Pro installation

eufy Wire-Free Hd Security Camera - 03

PRODUCT OVERVIEW

eufyCam 2 Pro

eufy Wire-Free Hd Security Camera - 04

  1.  Photosensitive sensor

  2. Camera lens

  3. Motion sensor

  4.  Microphone

  5. LED indicator
    eufy Wire-Free Hd Security Camera - 05

  6.  Sync button

  7. USB charging port

  8. Screw hole

ADDING EUFYCAM 2 Pro

Adding eufyCam 2 Pro to Your Existing System

On eufy Security app, follow the onscreen instructions to add your eufy devices. Choose Add Device, then select eufyCam 2 Pro to add it to your system.

eufy Wire-Free Hd Security Camera - 06

MOUNTING THE CAMERA

Find a Good Mounting Spot
To find a spot to mount eufyCam 2 Pro, you need to test wireless signal strength.

① Open the eufy Security app, go to Camera Settings > Mounting Guide.
② To test the wireless signal strength, take your camera and phone to the location where you want to mount the camera.
③ Move the camera as close to the HomeBase 2 as possible if the wireless.

eufy Wire-Free Hd Security Camera - 07 Select Height and Location

Hang eufyCam 2 Pro 7-10 ft (2-3 m) above the ground. This height maximizes the detection range of the motion sensor of eufyCam 2 Pro. Avoid placing eufyCam 2 Pro under direct sunlight.eufy Wire-Free Hd Security Camera -
08

Mount the camera
The camera can be mounted both indoors and outdoors. 1. Turn the knob of the mounting bracket clockwise to loosen and disassemble it.

eufy Wire-Free Hd Security Camera - 09

2. Drill holes with a 15/64 inch (5.95mm) drill bit, then insert the anchors into the holes; anchors are necessary for walls that are made out of hard materials such as concrete,  brick, or stucco.

eufy Wire-Free Hd Security Camera - 10

3. Firmly screw the base of the mounting bracket onto the wall. Fasten the ball knob of the bracket to the base of the bracket.

eufy Wire-Free Hd Security Camera - 11

4. Tighten eufyCam 2 Pro to the mounting bracket and adjust the viewing angle by checking the live stream feed in the Eufy Security app.

eufy Wire-Free Hd Security Camera - 12

Tips:
For troubleshooting, check Help on the eufy Security App.

Mount the Camera Indoors
Stick the camera directly to any flat surface made out of iron. Or you can use the indoor mount to mount the camera:
1. Drill a hole. Use the included anchor if it’s drywall and fasten the hook.

eufy Wire-Free Hd Security Camera - 13

2. Hang the indoor mount on the hookeufy Wire-Free Hd Security Camera -
14

3. Attach eufyCam 2 Pro to the indoor mount and adjust the viewing angle.

eufy Wire-Free Hd Security Camera - 15

CHARGING EUFYCAM 2 PRO

Charge eufyCam 2 Pro
Method 1

eufy Wire-Free Hd Security Camera - 16

LED indication Charging: Steady blue

Fully charged: Off
Charging time| 12 hours

NOTICE

FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
(1) Reorient or relocate the receiving antenna.
(2) Increase the separation between the equipment and receiver.
(3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
(4) Consult the dealer or an experienced radio/TV technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure conditions. The min separation distance is 20 cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.
FCC ID:2AOKB-T8114
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone:1-800-988-7973
This product complies with the radio interference requirements of the European Community.

Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the  declaration of conformity, visit the Web site www.eufylife.com
Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment. The suitable temperature for eufyCam 2 Pro and accessories is -20°C-50°C. When charging, please place the device in an environment that has a normal room temperature and good ventilation.

It is recommended to charge the device in an environment with a temperature that ranges from 5°C~25°C.
RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirements, use products that maintains a 20cm distance between the device and the human body.
CAUTION RISK OF EXPLOSION IF  BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Wi-Fi Operating Frequency
Range: 2412~2472MHz ; Wi-Fi Max
Output Power: 17.47 dBm
The following importer is the responsible party (contact for EU matters only) Importer: Anker Technology (UK) Ltd Importer Address: Suite B, Fairgate House, 205 Kings  Road, Tyseley, Birmingham, B11 2AA, United Kingdom

This product is designed and manufactured with high-quality materials and components, which can be recycled and reused.

iconicon - 1996 - recycal This symbol means the product must not be discarded as household waste and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling help protect natural resources, human health, and the environment. For more information on the disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

IC Statement
This device complies with Industry Canada licenceexempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.

IC RF Statement:
When using the product,  maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de l’utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matière d’exposition RF.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals