UCTRONICS Smart Bluetooth Robot Car Kit User Guide

UCTRONICS Smart Bluetooth Robot Car Kit User Guide

Product Overview

Packing list

• M330 socket screws 2 bars, M36 socket screws 6 bars

• M3*30 screws round head 8 bars

• M2 nuts, 2 pieces, M3 nuts, 16 pieces

• M210 screws round head 2 bars, M36 screws round head 6 bars

• M354 countersunk headscrews2 bars

• M24 micro servo screw 1 bar
  M28 micro servo self-tapping screws 2 bars

• Ultrasonic bracket 1 piece

• Servo accessory 1 set

• T-type fastener 8 pieces

• 18650 Battery 2 pieces

• 18650 Battery charger 1 piece

• Remote controller 1 piece

• Wheel 4 pieces

• Battery container 1 piece

• Servo 1 piece

• Deceleration DC motor 4 pieces

• 5 Pin line tracking module cable 1 piece
  4 Pin ultrasonic module cable 1 piece
  

• Fixing tool 1 set

• Chassis 1 piece

• Ultrasonic module 1 piece

• Motor drive board 1 piece

• UNO R3 board for Arduino 1 piece

• Line tracking module 1 piece

• HC-05 Bluetooth module 1 piece

DC motors installation

Step 1: Place the DC motor in the position marked on the chassis

For example, the Front L and Front R marks should be matched between the motor and chassis

Step 2: Install the DC motor

• 8 x M3*30 round head screws
• 4 x DC motors
• 8 x M3 nuts
• 1 x Chassis
• 8 x T-type fasteners

Step 3: Repeat the above steps

Tire installation

• 4 x Tires

Driver controller boards installation

Step 1: Install Arduino UNO R3

• 4 x M3 nuts
• 4 x M3*6 socket screws
• 4 x M3*6 round head screws
• 1 x UNO R3 board for Arduino

Step 2: Install motor driver board

Step 3: Install Bluetooth module

• 1 x HC-05 Bluetooth module

Battery container installation

• 2 x M3 nuts
• 1 x Battery container
• 2 x M3*6 socket screws
• 2 x M354 countersunk head screws

Pan servo installation

Step 1: Mount the Pan servo

• 1 x Servo
• 2 x M2 nuts
• 2 x M2*10 round head screws

Step 2: Mount the accessory of the Pan servo

• 1 x Servo accessory
• 1 x M2*4 micro servo screw
• 2 x M2*8 micro servo self-tapping screws
• 1 x Holder for HC-SR04 Ultrasonic Module

Step 3: Ultrasonic Module installation

• 1 x HC-SR04 Ultrasonic Module

Servo wiring

Connect the cables in the orientation shown in the illustration below. Note the positions of the yellow and brown wires

Tracking module wiring

Ultrasonic module wiring

Battery container wiring

DC motors wiring

J2 connector for Front DC motors

J1 connector for Rear DC motors

After finishing installing and wiring, please insert two 18650 batteries, push the button in the front of the motor board and wait 5 seconds for the car to work.

That is not all for this car kit.
There is a CD that comes with the car kit, check the CD For:

• Arduino example sketch and library
• Mobile apps to control the car
• Instruction manual
• Working modes demo
• and more

If you:

• Prefer an online and updated version
• Do not have a CD reader
• Find the CD defective or missing

Please go to:
https://www.uctronics.com/wiki/index.php?title=K0072

With additional content of:

• Troubleshooting
• User experience sharing
• and more

Dear Customer:

Thanks for using the UCTRONICS Smart Bluetooth Robot Car Kit K0072 for Arduino. You can find more information at the links below. Please don’t hesitate to let us know if you need any hands-on support from us.We love helping our customers learn and play with our products.

Contact us:

Custom support: support@uctronics.com
Business: sales@uctronics.com
Tel: +86 025 84271192
Web: http://www.uctronics.com/contacts/

References

• Contact Us with Contact Form
• K0072 - UCTRONICS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>