hohem iSteady Multi Stabilizing Gimbal for Compact Digital Camera User Guide

June 7, 2024
hohem

hohem iSteady Multi Stabilizing Gimbal for Compact Digital Camera User

Guide
text, whiteboard

3-Axis Stabilizing Gimbal for Compact Digital Camera User Guide V1.0

DISCLAIMER

  • Please use the product in accordance with the user guide.
  • Make sure your camera device is mounted before powering on the gimbal.
  • Keep the gimbal away from Pre and heat source.
  • Prohibiting the product to be used for any illegal purpose. The user who violates the regulation will be responsible for all the consequences by purchasing and using the product.
  • For any products which comes from non-normal source, we will not be at any service.
  • For any question, please contact the technical support of Hohem Tech. We will be always at your service to provide the technical support and advice for any improper using of gimbal.
  • Hohem Tech reserves the right of Pnal explanation.

Product Overview

diagram, engineering drawing

  1. Tilt Motor

  2. Thumb Screw 1

  3. Mini USB(camera control)

  4. Pan Motor

  5. Bluetooth Light

  6. Joystick

  7. Slider

  8. Mode Light

  9. Mode Button

  10. ON/OFF(Shutter Button)

  11. Handle(Batter y inside)

  12. Roll Motor

  13. Quick Release Plate

  14. Thumb Screw 2

  15. Quick Release Plate Bolt

  16. Power Indicator Light
    diagram, engineering drawing

  17. Thumb Screw 3

  18. 1/4 Inch Screw Hole 1

  19. Trigger Button

  20. USB Port

  21. 1/4 Inch Screw Hole 2

Accessories List

Tripod1
Quick Release Plate
1 Smartphone Holder1 SONY Multi Camera Control Cable1 Micro USB Charging Cable1 Carr y Case1 Thumb Screw 2 User Guide1

Gimbal Charging

Charge the gimbal fully before using it for the first time. USB Port: Power bank output
Micro USB Port: Gimbal charging port

  • Low Battery Warning· The Mode Light Blinks
    Indicator Lights blink: Charging in process
    4 LED light on: Fully charged

4 LED lights on: 100%      3 LED lights on: 75%
2 LED lights on: 50%        1 LED light on 25%

Camera/Phone Mounting

CAUTION

Please mount your camera/phone before turning on the gimbal.

Camera Mounting:
* Some action cameras must add an adaptor with 1/4 screw hole.

  1. Mount the quick release plate on camera.

  2. Insert the camera with quick release plate(A) into the slot of clamping plate(B) and tighten the thumb screw

Supported Cameras:

  1. Digital Camera: SONY RX100 series, Canon G series,Panosonic DMC-LX10
  2. Action Camera: GoPro Hero series, SONY RX0 series, SONY X300, YI CAM, SJCAM
  3. Payload: 400g

Phone Mounting:

  1. Mount the phone holder on the quick release plate with thumb screw

  2. Insert the phone holder with quick release plate into the slot of clamping plate and mount your phone on the holder, then tighten the quick

Balancing

It is recommended to turn on the camera before balancing it on the gimbal
3.Balance the camera through left and right

Slide the roll arm to balance the camera through left and right, tighten the thumb screw after the camera is well balanced.

Operation Instruction

App “Hohem Gimbal” Instruction

Bluetooth Connection:

  1. Enable the bluetooth of smartphone and turn on the gimbal.(Make sure the device is mounted on the gimbal)
  2. Open the App “Hohem Gimbal” and choose the correct product model “iSteady Multi”to connect.
  3. Choose the correct device to enter into(For compact camera and action camera mounted,click “camera” to enter; For smartphone mounted,click “phone” to enter.) It allows to connect the bluetooth of smartphone for mounting smartphone on gimbal.Enter the smartphone bluetooth list to search signal “Smartphone Gimbal” to connect the gimbal, which enables the gimbal to control the original phone camera to take phone and record video.

【FAQ】Fail to connect the bluetooth on smartphone or app?

  1.  Reset network setting.
  2. Disable WiFi and cancel the pairing of “Smartphone Gimbal” connection.
  3. Reconnection

App “Hohem Gimbal” Instruction

Enter into the main function interface of smartphone in the App

  1. Home
  2. Bluetooth
  3. Power Status
  4. Axis angle display in sync
  5. Motion Timelapse
  6. Re-center
  7. Remote Control
  8. Switch Work Mode

App “Hohem Gimbal” Instruction

into the main function interface of smartphone in the App

  1. Home
  2. Setting
  3. Front/Rear camera
  4. Flash
  5. Camera Setting
  6. Album
  7. Object Tracking
  8. Zoom & Focus
  9. Bluetooth
  10. Face Tracking
  11. Shutter Button
  12. Panorama
  13. Motion Timelapse

App “Hohem Gimbal” Instruction

Other App Functions

  1. Gimbal Specs Setting:
    A. Following Speed (To adjust the following speed of pan/tilt/roll axes)
    B. Joystick Speed (To adjust the rotating speed by control the joystick)
    C. Following Dead Area (No following movement when the rotate angle is less than dead area setting)
    D. Trim (To adjust the tilt/roll axis in small angle to get a perfect balance)
    E. Joystick Reverse(To reverse the rotation direction by control the joystick)
    F. Motor Torsion (To adjust the motor torsion of pan/tilt/roll axes, which is useful to solve the vibrate
    issue due to lightweight or over weight mobile phone)

  2. Firmware Upgrade: The firmware is subject to upgrade without a fixed schedule. Firmware upgarde is help to optimize the working of gimbal, please refer to page 14 for details.

  3. Calibration: It requires to calibrate the gimbal only when you notice any kind of not level or drift
    on any of the axes, please refer to page 13 for details.

  4. Operation Instruction: For any questions, please refer to the user guide for details, the content is subject to change without prior notice.

Calibration

It requires to calibrate the gimbal if you notice it is not work properly as below.

  1. The pitch angle is not level with the horizontal surface.
  2. The roll angle is not parallel to the horizontal surface.
  3. The pan axis drifts when the gimbal is on all lock mode.

Calibration Instruction

Method 1:Off-line Calibration
(1)Power on the gimbal, long press the mode button over 6 seconds till the mode light on. *if the off-line calibration is not useful, please refer to 【Method 2】
(2)Laying the gimbal on a static flat surface without any vibrate. Calibration is completed once the mode light flash twice.

Method 2:6-Side Calibration Via App
Please make sure the gimbal is connected with app via bluetooth successfully, then enter
“Calibration” and follow the instruction in the app to calibrate the gimbal.

Firmware Upgrade

Please make sure the gimbal is connected with app via bluetooth successfully, then enter the “Firmware Upgrade” and follow the instruction to upgrade the latest firmware.

FAQ

Q: Why the gimbal vibrates after powering on?
A: Make sure your camera is mounted firmly and well balanced before powering on the gimbal, do not turn on the gimbal without a balanced load, as doing so many damage the
motors, please refer to page 5. 6 for more details. For some lightweight mobile phone, it needs to adjust the motor torsion, please refer to page 12 for details.

Q: How to connect the gimbal via app?
A:Please be noted that the bluetooth and gimbal must be connected directly in the app “Hohem Gimbal”, rather than connecting in the smartphone bluetooth list. Make sure all the permission is allow when you open the app for the first time. Please refer to the tutorial video on our YouTube channel for more details.
Q: How to do if the gimbal is not level or drift after powering on?
A: Please refer to page 13 for details.

Parameters

Weight 530g include battery
Main Material High performance composite
Payload 400g
Supported Devices 1.Digital Camera: SONY RX100 series, Canon G series,

Panosonic DMC-LX10 2.Smartphone: iPhone series and Android phone.

3.Action Camera: GoPro Hero series, SONY RX0 , SONY X3000, YI CAM, SJCAM

Battery Capacity| 3600 mAh
Working Time| 8 hours
Charging Time| 3.5 hours

Mechanical Range

| Panning:600°
Rolling:320°
Tilting:320°
Working Temperature| -10~45 ℃
Motors Protection| Gimbal is able to power off automatically due to improper operation of

the motors.

Standard   Accessories| Tripod1;Quick Release Plate1;Smartphone Holder1; SONY Multi Camera Control Cable1; Micro USB Charging Cable1; Carry Case1;

Thumb Screw *2

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals