ESPRESSIF ESP32-S3-WROOM-1 Bluetooth Module User Manual
- June 5, 2024
- ESPRESSIF
Table of Contents
ESP32S3WROOM1
ESP32S3WROOM1U
User Manual
2.4 GHz WiFi (802.11 b/g/n) and Bluetooth5 (LE) module
Built around ESP32S3 series of SoCs, Xtensa ® dualcore 32bit LX7
microprocessor
Flash up to 16 MB, PSRAM up to 8 MB
36 GPIOs, a rich set of peripherals
Onboard PCB antenna or external antenna connector
Module Overview
1.1 Features
CPU and OnChip Memory
- ESP32-S3 series of SoCs embedded, Xtensa ® dual-core 32-bit LX7 microprocessor, up to 240 MHz
- 384 KB ROM
- 512 KB SRAM
- 16 KB SRAM in RTC
- Up to 8 MB PSRAM
WiFi
- 802.11 b/g/n
- Bit rate: 802.11n up to 150 Mbps
- A-MPDU and A-MSDU aggregation
- 0.4 µs guard interval support
- Center frequency range of operating channel: 2412 ~ 2462 MHz
Bluetooth
- Bluetooth LE: Bluetooth 5, Bluetooth mesh
- 2 Mbps PHY
- Long-range mode
- Advertising extensions
- Multiple advertisement sets
- Channel selection algorithm #2
Peripherals
- GPIO, SPI, LCD interface, Camera interface, UART, I2C, I2S, remote control, pulse counter, LED PWM, USB 1.1 OTG, USB Serial/JTAG controller, MCPWM, SDIO host, GDMA, TWAI ® controller (compatible with ISO 11898-1), ADC, touch sensor, temperature sensor, timers and watchdogs
Integrated Components on Module
- 40 MHz crystal oscillator
- Up to 16 MB SPI flash
Antenna Options
- On-board PCB antenna (ESP32-S3-WROOM-1)
- External antenna via a connector (ESP32-S3-WROOM-1U)
Operating Conditions
-
Operating voltage/Power supply: 3.0 ~ 3.6 V
-
Operating ambient temperature:
– 65 °C version: –40 ~ 65 °C
– 85 °C version: –40 ~ 85 °C
– 105 °C version: –40 ~ 105 °C -
Dimensions: See Table 1
1.2 Description
ESP32-S3-WROOM-1 and ESP32-S3-WROOM-1U are two powerful, generic Wi-Fi +
Bluetooth LE MCU modules that are built around the ESP32-S3 series of SoCs. On
top of a rich set of peripherals, the acceleration for neural network
computing and signal processing workloads provided by the SoC makes the
modules an ideal choice for a wide variety of application scenarios related to
AI and Artificial Intelligence of Things (IoT), such as wake word detection,
speech commands recognition, face detection, and recognition, smart home,
smart appliances, smart control panel, smart speaker, etc.
ESP32-S3-WROOM-1 comes with a PCB antenna. ESP32-S3-WROOM-1U comes with an
external antenna connector. A wide selection of module variants is available
for customers as shown in Table 1. Among the module variants, those embedded
ESP32-S3R8 operate at –40 ~ 65 °C ambient temperature, ESP32-S3-WROOM-1-H4 and
ESP32-S3-WROOM-1U-H4 operate at –40 ~ 105 °C ambient temperature, and other
module variants operate at –40 ~ 85 °C ambient temperature.
Table 1: Ordering Information
Ordering Code| Chip Embedded| Flash (MB)| PSRAM (MB)|
Dimensions (mm)
---|---|---|---|---
ESP32-S3-WROOM-1-N4| ESP32-S3| 4| 0| 18 × 25.5 × 3.1
ESP32-S3-WROOM-1-N8| ESP32-S3| 8| 0
ESP32-S3-WROOM-1-N16| ESP32-S3| 16| 0
ESP32-S3-WROOM-1-H4 (105 °C)| ESP32-S3| 4| 0
ESP32-S3-WROOM-1-N4R2| ESP32-S3R2| 4| 2 (Quad SPI)
ESP32-S3-WROOM-1-N8R2| ESP32-S3R2| 8| 2 (Quad SPI)
ESP32-S3-WROOM-1-N16R2| ESP32-S3R2| 16| 2 (Quad SPI)
ESP32-S3-WROOM-1-N4R8 (65 °C)| ESP32-S3R8| 4| 8 (Octal SPI)
ESP32-S3-WROOM-1-N8R8 (65 °C)| ESP32-S3R8| 8| 8 (Octal SPI)
ESP32-S3-WROOM-1-N16R8 (65 °C)| ESP32-S3R8| 16| 8 (Octal SPI)
ESP32-S3-WROOM-1U-N4| ESP32-S3| 4| 0| 18 × 19.2 × 3.2
ESP32-S3-WROOM-1U-N8| ESP32-S3| 8| 0
ESP32-S3-WROOM-1U-N16| ESP32-S3| 16| 0
ESP32-S3-WROOM-1U-H4 (105 °C)| ESP32-S3| 4| 0
ESP32-S3-WROOM-1U-N4R2| ESP32-S3R2| 4| 2 (Quad SPI)
ESP32-S3-WROOM-1U-N8R2| ESP32-S3R2| 8| 2 (Quad SPI)
ESP32-S3-WROOM-1U-N16R2| ESP32-S3R2| 16| 2 (Quad SPI)
ESP32-S3-WROOM-1U-N4R8 (65 °C)| ESP32-S3R8| 4| 8 (Octal SPI)
ESP32-S3-WROOM-1U-N8R8 (65 °C)| ESP32-S3R8| 8| 8 (Octal SPI)
ESP32-S3-WROOM-1U-N16R8 (65 °C)| ESP32-S3R8| 16| 8 (Octal SPI)
At the core of the modules is an ESP32-S3 series of SoC *, an Xtensa ® 32-bit
LX7 CPU that operates at up to 240 MHz. You can power off the CPU and make use
of the low-power co-processor to constantly monitor the peripherals for
changes or crossing of thresholds.
ESP32-S3 integrates a rich set of peripherals including SPI, LCD, Camera
interface, UART, I2C, I2S, remote control, pulse counter, LED PWM, USB
Serial/JTAG controller, MCPWM, SDIO host, GDMA, TWAI ® controller (compatible
with ISO 11898-1), ADC, touch sensor, temperature sensor, timers, and
watchdogs, as well as up to 45 GPIOs. It also includes a full-speed USB 1.1
On-The-Go (OTG) interface to enable USB communication.
Note:
- For more information on the ESP32-S3 series of SoCs, please refer to ESP32-S3 Series Datasheet.
Pin Definitions
2.1 Pin Layout
The pin diagram is applicable for ESP32-S3-WROOM-1 and ESP32-S3-WROOM-1U, but
the latter has no keep-out zone.
2.2 Pin Description
The module has 41 pins. See pin definitions in Table 2.
For explanations of pin names and function names, as well as configurations of
peripheral pins, please refer to ESP32-S3 Series Datasheet.
Table 2: Pin Definitions
Name | No. | Type a | Function |
---|---|---|---|
GND | 1 | P | GND |
3V3 | 2 | P | Power supply |
EN | 3 | I | High: on, enables the chip. Low: off, the chip powers off. |
Note: Do not leave the EN pin floating.
IO4| 4| I/O/T| RTC_GPIO4, GPIO4, TOUCH4, ADC1_CH3
IO5| 5| I/O/T| RTC_GPIO5, GPIO5, TOUCH5, ADC1_CH4
IO6| 6| I/O/T| RTC_GPIO6, GPIO6, TOUCH6, ADC1_CH5
IO7| 7| I/O/T| RTC_GPIO7, GPIO7, TOUCH7, ADC1_CH6
IO15| 8| I/O/T| RTC_GPIO15, GPIO15, U0RTS, ADC2_CH4, XTAL_32K_P
IO16| 9| I/O/T| RTC_GPIO16, GPIO16, U0CTS, ADC2_CH5, XTAL_32K_N
IO17| 10| I/O/T| RTC_GPIO17, GPIO17, U1TXD, ADC2_CH6
IO18| 11| I/O/T| RTC_GPIO18, GPIO18, U1RXD, ADC2_CH7, CLK_OUT3
IO8| 12| I/O/T| RTC_GPIO8, GPIO8, TOUCH8, ADC1_CH7, SUBSPICS1
IO19| 13| I/O/T| RTC_GPIO19, GPIO19, U1RTS, ADC2_CH8, CLK_OUT2, USB_D-
IO20| 14| I/O/T| RTC_GPIO20, GPIO20, U1CTS, ADC2_CH9, CLK_OUT1, USB_D+
IO3| 15| I/O/T| RTC_GPIO3, GPIO3, TOUCH3, ADC1_CH2
IO46| 16| I/O/T| GPIO46
IO9| 17| I/O/T| RTC_GPIO9, GPIO9, TOUCH9, ADC1_CH8, FSPIHD, SUSPEND
IO10| 18| I/O/T| RTC_GPIO10, GPIO10, TOUCH10, ADC1_CH9, FSPICS0, FSPIIO4,
SUBSPICS0
IO11| 19| I/O/T| RTC_GPIO11, GPIO11, TOUCH11, ADC2_CH0, FSPID, FSPIIO5,
SUSPEND
IO12| 20| I/O/T| RTC_GPIO12, GPIO12, TOUCH12, ADC2_CH1, FSPICLK, FSPIIO6,
SUBSPICLK
IO13| 21| I/O/T| RTC_GPIO13, GPIO13, TOUCH13, ADC2_CH2, FSPIQ, FSPIIO7,
SUBSPIQ
IO14| 22| I/O/T| RTC_GPIO14, GPIO14, TOUCH14, ADC2_CH3, FSPIWP, FSPIDQS,
SUBSPIWP
IO21| 23| I/O/T| RTC_GPIO21, GPIO21
IO47| 24| I/O/T| SPICLK_P_DIFF,GPIO47, SUBSPICLK_P_DIFF
IO48| 25| I/O/T| SPICLK_N_DIFF,GPIO48, SUBSPICLK_N_DIFF
IO45| 26| I/O/T| GPIO45
IO0| 27| I/O/T| RTC_GPIO0, GPIO0
IO35 b| 28| I/O/T| SPIIO6, GPIO35, FSPID, SUBSPID
IO36 b| 29| I/O/T| SPIIO7, GPIO36, FSPICLK, SUBSPICLK
IO37 b| 30| I/O/T| SPIDQS, GPIO37, FSPIQ, SUBSPIQ
IO38| 31| I/O/T| GPIO38, FSPIWP, SUBSPIWP
IO39| 32| I/O/T| MTCK, GPIO39, CLK_OUT3, SUBSPICS1
IO40| 33| I/O/T| MTDO, GPIO40, CLK_OUT2
IO41| 34| I/O/T| MTDI, GPIO41, CLK_OUT1
Table 2 – contd from the previous page
Name | No. | Type a | Function |
---|---|---|---|
IO42 | 35 | I/O/T | MTMS, GPIO42 |
RXD0 | 36 | I/O/T | U0RXD, GPIO44, CLK_OUT2 |
TXD0 | 37 | I/O/T | U0TXD, GPIO43, CLK_OUT1 |
IO2 | 38 | I/O/T | RTC_GPIO2, GPIO2, TOUCH2, ADC1_CH1 |
IO1 | 39 | I/O/T | RTC_GPIO1, GPIO1, TOUCH1, ADC1_CH0 |
GND | 40 | P | GND |
READ | 41 | P | GND |
a P: power supply; I: input; O: output; T: high impedance. Pin functions in
bold font are the default pin functions.
b In module variants that have embedded OSPI PSRAM, i.e., that embed
ESP32-S3R8, pins IO35, IO36, and IO37 connect to the OSPI PSRAM and are not
available for other uses.
Get Started
3.1 What You Need
To develop applications for the module you need:
- 1 x ESP32-S3-WROOM-1 or ESP32-S3-WROOM-1U
- 1 x Espressif RF testing board
- 1 x USB-to-Serial board
- 1 x Micro-USB cable
- 1 x PC running Linux
In this user guide, we take Linux operating system as an example. For more
information about the configuration on Windows and macOS, please refer to ESP-
IDF Programming Guide.
3.2 Hardware Connection
- Solder the ESP32-S3-WROOM-1 or ESP32-S3-WROOM-1U module to the RF testing board as shown in Figure 2.
- Connect the RF testing board to the USB-to-Serial board via TXD, RXD, and GND.
- Connect the USB-to-Serial board to the PC.
- Connect the RF testing board to the PC or a power adapter to enable a 5 V power supply, via the Micro-USB cable.
- During download, connect IO0 to GND via a jumper. Then, turn ”ON” the testing board.
- Download firmware into flash. For details, see the sections below.
- After download, remove the jumper on IO0 and GND.
- Power up the RF testing board again. The module will switch to working mode. The chip will read programs from flash upon initialization.
Note:
IO0 is internally logic high. If IO0 is set to pull-up, the Boot mode is
selected. If this pin is pull-down or left floating, the Download mode is
selected. For more information on ESP32-S3-WROOM-1 or ESP32-S3-WROOM-1U,
please refer to ESP32-S3 Series Datasheet.
3.3 Set up Development Environment
The Espressif IoT Development Framework (ESP-IDF for short) is a framework for
developing applications based on the Espressif ESP32. Users can develop
applications with ESP32-S3 in Windows/Linux/macOS based on ESP-IDF. Here we
take Linux operating system as an example.
3.3.1 Install Prerequisites
To compile with ESP-IDF you need to get the following packages:
-
CentOS 7 & 8:
1 sudo yum -y update && Sudo yum install git wget flex bison gperf python3 python3pip
2 python3-setuptools CMake ninja-build ccache dfu-util busby -
Ubuntu and Debian:
1 Sudo apt-get install git wget flex bison gperf python3 python3-pip python3setuptools
2 cmake ninja-build ccache life-dev libssl-dev dfu-util libusb-1.0-0 -
Arch:
1 sudo Pacman -S –needed GCC git make flex bison gperf python-pip CMake ninja ccache 2 dfu-util libusb
Note:
- This guide uses the directory ~/esp on Linux as an installation folder for ESP-IDF.
- Keep in mind that ESP-IDF does not support spaces in paths.
3.3.2 Get ESPIDF
To build applications for ESP32-S3-WROOM-1 or ESP32-S3-WROOM-1U module, you
need the software libraries provided by Espressif in the ESP-IDF repository.
To get ESP-IDF, create an installation directory ( ~/esp) to download ESP-IDF
to and clone the repository with ‘git clone’:
- mkdir -p ~/esp
- cd ~/esp
- git clone –recursive https://github.com/espressif/esp-idf.git
ESP-IDF will be downloaded into ~/esp/esp-idf. Consult ESP-IDF Versions for
information about which ESP-IDF
version to use in a given situation.
3.3.3 Set up Tools
Aside from the ESP-IDF, you also need to install the tools used by ESP-IDF,
such as the compiler, debugger, Python packages, etc. ESP-IDF provides a
script named ’install.sh’ to help set up the tools in one go.
1 cd ~/esp/esp-idf
2 ./install.sh
3.3.4 Set up Environment Variables
The installed tools are not yet added to the PATH environment variable. To
make the tools usable from the command line, some environment variables must
be set. ESP-IDF provides another script export. sh’ which does that. In the
terminal where you are going to use ESP-IDF, run:
1 . $HOME/esp/esp-IDF/export.sh
Now everything is ready, you can build your first project on the
ESP32-S3-WROOM-1 or ESP32-S3-WROOM-1U module.
3.4 Create Your First Project
3.4.1 Start a Project
Now you are ready to prepare your application for the ESP32-S3-WROOM-1 or
ESP32-S3-WROOM-1U module.
You can start with the get-started/hello_world project from the examples
directory in ESP-IDF.
Copy get-started/hello_world to ~/esp directory:
1 cd ~/esp
2 cp -r $IDF_PATH/examples/get-started/hello_world .
There is a range of example projects in the examples directory in ESP-IDF. You
can copy any project in the same way as presented above and run it. It is also
possible to build examples in place, without copying them first.
3.4.2 Connect Your Device
Now connect your module to the computer and check under what serial port the
module is visible. Serial ports in Linux start with ‘/dev/TTY in their names.
Run the command below two times, first with the board unplugged, then with
plugged in. The port which appears the second time is the one you need:
1 ls /dev/tty*
Note:
Keep the port name handy as you will need it in the next steps.
3.4.3 Configure
Navigate to your ‘hello_world’ directory from Step 3.4.1. Start a Project, set
ESP32-S3 chip as the target, and run the project configuration utility
‘menuconfig’.
1 cd ~/esp/hello_world
2 idf.py set-target esp32s3
3 idf.py menuconfig
Setting the target with ‘idf.py set-target esp32s3’ should be done once, after
opening a new project. If the project contains some existing builds and
configurations, they will be cleared and initialized. The target may be saved
in the environment variable to skip this step. See Selecting the Target for
additional information.
If the previous steps have been done correctly, the following menu appears:
You are using this menu to set up project-specific variables, e.g. Wi-Fi
network name and password, the processor speed, etc. Setting up the project
with menuconfig may be skipped for “hello_word”. This example will run with
the default configuration The colors of the menu could be different in your
terminal. You can change the appearance with the option ‘–style’. Please run
‘idf.py menuconfig –help for further information.
3.4.4 Build the Project
Build the project by running:
1 idf.py build
This command will compile the application and all ESP-IDF components, then it
will generate the bootloader, partition table, and application binaries.
1 $ idf.py build
2 Running CMake in directory /path/to/hello_world/build
3 Executing ”CMake -G Ninja –warn-uninitialized /path/to/hello_world”…
4 Warn about uninitialized values.
5 — Found Git: /usr/bin/git (found version ”2.17.0”)
6 — Building empty aws_iot component due to configuration
7 — Component names: …
8 — Component paths: …
9
10 … (more lines of build system output)
11
12 [527/527] Generating hello_world.bin
13 esptool.py v2.3.1
14
15 Project build complete. To flash, run this command:
16 ../../../components/esptool_py/esptool/esptool.py -p (PORT) -b 921600
17 write_flash –flash_mode dio –flash_size detect –flash_freq 40m
18 0x10000 build/hello_world.bin build 0x1000 build/bootloader/bootloader.bin
0x8000
19 build/partition_table/partition-table.bin
20 or run ’idf.py -p PORT flash’
If there are no errors, the build will finish by generating the firmware binary .bin file.
3.4.5 Flash onto the Device
Flash the binaries that you just built onto your module by running:
1 idf.py -p PORT [-b BAUD] flash
Replace PORT with your ESP32-S3 board’s serial port name from Step: Connect
Your Device.
You can also change the flasher baud rate by replacing BAUD with the baud rate
you need. The default baud rate is 460800.
For more information on idf.py arguments, see idf.py.
Note:
The option ‘flash‘ automatically builds and flashes the project, so running
‘idf.py build‘ is not necessary.
When flashing, you will see the output log similar to the following:
1 …
2 esptool.py esp32s3 -p /dev/ttyUSB0 -b 460800 –before=default_reset
–after=hard_reset
3 write_flash –flash_mode dio –flash_freq 80m –flash_size 2MB 0x0
bootloader/bootloader.
bin
4 0x10000 hello_world.bin 0x8000 partition_table/partition-table.bin
5 esptool.py v3.2-dev
6 Serial port /dev/ttyUSB0
7 Connecting….
8 Chip is ESP32-S3
9 Features: WiFi, BLE
10 Crystal is 40MHz
11 MAC: 7c:df:a1:e0:00:64
12 Uploading stub…
13 Running stub…
14 Stub running…
15 Changing baud rate to 460800
16 Changed.
17 Configuring flash size…
18 Flash will be erased from 0x00000000 to 0x00004fff…
19 Flash will be erased from 0x00010000 to 0x00039fff…
20 Flash will be erased from 0x00008000 to 0x00008fff…
21 Compressed 18896 bytes to 11758…
22 Writing at 0x00000000… (100 %)
23 Wrote 18896 bytes (11758 compressed) at 0x00000000 in 0.5 seconds
(effective 279.9 kbit/s)
…
24 Hash of data verified.
25 Compressed 168208 bytes to 88178…
26 Writing at 0x00010000… (16 %)
27 Writing at 0x0001a80f… (33 %)
28 Writing at 0x000201f1… (50 %)
29 Writing at 0x00025dcf… (66 %)
30 Writing at 0x0002d0be… (83 %)
31 Writing at 0x00036c07… (100 %)
32 Wrote 168208 bytes (88178 compressed) at 0x00010000 in 2.4 seconds
(effective 569.2 kbit/s
)…
33 Hash of data verified.
34 Compressed 3072 bytes to 103…
35 Writing at 0x00008000… (100 %)
36 Wrote 3072 bytes (103 compressed) at 0x00008000 in 0.1 seconds (effective
478.9 kbit/s)…
37 Hash of data verified.
38
39 Leaving…
40 Hard resetting via RTS pin…
41 Done
If there are no issues by the end of the flash process, the board will reboot and start up the “hello_world” application.
3.4.6 Monitor
To check if “hello_world” is indeed running, type ‘idf.py -p PORT monitor‘ (Do
not forget to replace PORT with your serial port name).
This command launches the IDF Monitor application:
1 $ idf.py -p /dev/ttyUSB0 monitor
2 Running idf_monitor in directory […]/esp/hello_world/build
3 Executing ”python […]/esp-idf/tools/idf_monitor.py -b 115200
4 […]/esp/hello_world/build/hello-world.elf”…
5 — idf_monitor on /dev/ttyUSB0 115200 —
6 — Quit: Ctrl+] | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H —
7 ets Jun 8 2016 00:22:57
8
9 rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
10 ets Jun 8 2016 00:22:57
11 …
After startup and diagnostic logs scroll up, you should see “Hello world!”
printed out by the application.
1 …
2 Hello world!
3 Restarting in 10 seconds…
4 This is esp32s3 chip with 2 CPU core(s), This is esp32s3 chip with 2 CPU
core(s), WiFi/BLE
,
5 silicon revision 0, 2MB external flash
6 Minimum free heap size: 390684 bytes
7 Restarting in 9 seconds…
8 Restarting in 8 seconds…
9 Restarting in 7 seconds…
To exit the IDF monitor use the shortcut Ctrl+].
That’s all that you need to get started with the ESP32-S3-WROOM-1 or ESP32-S3
-WROOM-1U module! Now you
are ready to try some other examples in ESP-IDF, or go right to developing
your own applications.
U.S. FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part15 of the FCC Rules.
These limits are designed to protect reasonably against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This device and its antenna must not be co-located
or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter.
OEM Integration Instructions
This device is intended only for OEM integrators under the following
conditions The module can be used to install in another host. The antenna must
be installed such that 20 cm is maintained between the antenna and users, and
the transmitter module may not be co-located with any other transmitter or
antenna. The module shall be only used with the integral antenna(s) that has
been originally tested and certified with this module. As long as the 3
conditions above are met, further transmitter tests will not be required.
However, the OEM integrator is still responsible for testing their end-product
for any additional compliance requirement with this module installed (for
example, digital device emission, PC peripheral requirements, etc.)
Notice:
In the event that these conditions cannot be met (for example certain laptop
configuration or co-location with another transmitter), then the FCC
authorization for this module in combination with the host equipment is no
longer considered valid and the FCC ID of the module cannot be used on the
final product. In these circumstances, the OEM integrator will be responsible
for re-evaluating the end product (including the transmitter) and obtaining a
separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in devices where the
antenna may be installed such that 20 cm may be maintained between the antenna
and users. The final end product must be labeled in a visible area with the
following: “Contains FCC ID: 2AC7Z-ESPS3WROOM1”.
IC Statement
This device complies with Industry Canada’s license-exempt RSS. Operation is subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator & your body.
RSS247 Section 6.4 (5)
The device could automatically discontinue transmission in case of the absence
of information to transmit or operational failure. Note that this is not
intended to prohibit transmission of control or signaling information or the
use of repetitive codes where required by the technology.
This device is intended only for OEM integrators under the following
conditions: (For module device use)
- The antenna must be installed such that 20 cm is maintained between the antenna and users, and
- The transmitter module may not be co-located with any other transmitter or antenna.
As long as the 2 conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or colocation with another transmitter), then the Canada
authorization is no longer considered valid and the IC ID can not be used on
the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate Canada
authorization.
End Product Labeling
This transmitter module is authorized only for use in devices where the
antenna may be installed such that 20 cm may be maintained between the antenna
and users. The final end product must be labeled in a visible area with the
following: “Contains IC: 21098-ESPS3WROOM1”.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module. The end user manual shall include
all required regulatory information/warning as shown in this manual.
Related Documentation and Resources
Related Documentation
-
ESP32-S3 Series Datasheet – Specifications of the ESP32-S3 hardware.
-
ESP32-S3 Technical Reference Manual – Detailed information on how to use the ESP32-S3 memory and peripherals.
-
ESP32-S3 Hardware Design Guidelines – Guidelines on how to integrate the ESP32-S3 into your hardware product.
-
Certificates
http://espressif.com/en/support/documents/certificates -
Documentation Updates and Update Notification Subscription
http://espressif.com/en/support/download/documents
Developer Zone
-
ESP-IDF Programming Guide for ESP32-S3 – Extensive documentation for the ESP-IDF development framework.
-
ESP-IDF and other development frameworks on GitHub.
http://github.com/espressif -
ESP32 BBS Forum – Engineer-to-Engineer (E2E) Community for Espressif products where you can post questions, share knowledge, explore ideas, and help solve problems with fellow engineers.
http://esp32.com/ -
The ESP Journal – Best Practices, Articles, and Notes from Espressif folks.
http://blog.espressif.com/ -
See the tabs SDKs and Demos, Apps, Tools, AT Firmware.
http://espressif.com/en/support/download/sdks-demos
Products
-
ESP32-S3 Series SoCs – Browse through all ESP32-S3 SoCs.
http://espressif.com/en/products/socs?id=ESP32-S3 -
ESP32-S3 Series Modules – Browse through all ESP32-S3-based modules.
http://espressif.com/en/products/modules?id=ESP32-S3 -
ESP32-S3 Series DevKits – Browse through all ESP32-S3-based devkits.
http://espressif.com/en/products/devkits?id=ESP32-S3 -
ESP Product Selector – Find an Espressif hardware product suitable for your needs by comparing or applying filters.
http://products.espressif.com/#/product-selector?language=en
Contact Us
- See the tabs Sales Questions, Technical Enquiries, Circuit Schematic & PCB Design Review, Get Samples (Online stores), Become Our Supplier, Comments & Suggestions.
http://espressif.com/en/contact-us/sales-questions
Revision History
Date | Version | Release notes |
---|---|---|
10/29/2021 | v0.6 | Overall update for chip revision 1 |
7/19/2021 | v0.5.1 | Preliminary release, for chip revision 0 |
Disclaimer and Copyright Notice
Information in this document, including URL references, is subject to change
without notice.
ALL THIRD-PARTY’S INFORMATION IN THIS DOCUMENT IS PROVIDED AS IS WITH NO
WARRANTIES TO ITS AUTHENTICITY AND ACCURACY.
NO WARRANTY IS PROVIDED TO THIS DOCUMENT FOR ITS MERCHANTABILITY, NON-
INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE, NOR DOES ANY WARRANTY
OTHERWISE ARISE OUT OF ANY PROPOSAL, SPECIFICATION, OR SAMPLE.
All liability, including liability for infringement of any proprietary rights,
relating to the use of information in this document is disclaimed. No licenses
express or implied, by estoppel or otherwise, to any intellectual property
rights are granted herein.
The Wi-Fi Alliance Member logo is a trademark of the Wi-Fi Alliance. The
Bluetooth logo is a registered trademark of Bluetooth SIG.
All trade names, trademarks, and registered trademarks mentioned in this
document are the property of their respective owners and are hereby
acknowledged.
Pre-release v0.6 Copyright
© 2022 Espressif Systems (Shanghai) Co., Ltd. All rights reserved.
References
- ESP32 Forum - Index page
- ESP DevKits | Espressif Systems
- ESP Modules | Espressif Systems
- ESP SoCs | Espressif Systems
- Espressif Systems · GitHub
- ESP Product Selector
- Wireless SoCs, Software, Cloud and AIoT Solutions | Espressif Systems
- Build System - ESP32-S3 - — ESP-IDF Programming Guide latest documentation
- Build System - ESP32-S3 - — ESP-IDF Programming Guide latest documentation
- Get Started - ESP32-S3 - — ESP-IDF Programming Guide latest documentation
- ESP-IDF Versions - ESP32-S3 - — ESP-IDF Programming Guide latest documentation
- GitHub - espressif/esp-idf: Espressif IoT Development Framework. Official development framework for Espressif SoCs.
- esp-idf/examples/get-started/hello_world at c77c4ccf6c43ab09fd89e7c907bf5cf2a3499e3b · espressif/esp-idf · GitHub
- esp-idf/examples at master · espressif/esp-idf · GitHub
- Documentation Feedback | Espressif Systems
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>