NETGEAR MS105 5 Port Multi Gigabit 2.5G Ethernet Unmanaged Switch Installation Guide
- June 3, 2024
- NETGEAR
Table of Contents
MS105 5 Port Multi Gigabit 2.5G Ethernet Unmanaged Switch
Installation Guide
Package contents
- NETGEAR 5‑port Multi‑Gigabit 2.5G Ethernet Unmanaged Switch
- Power adapter
- Wall‑mount installation kit
- Rubber feet
- Installation Guide
Register the switch
-
From a computer or mobile device that is connected to the Internet, visit my.netgear.com.
-
Log in to your NETGEAR account.
NOTE: If you don’t have a free NETGEAR account, you can create one.
The Your Registered Products page displays. -
Click the REGISTER NEW PRODUCT button.
-
In the SERIAL NUMBER field, type the serial number of your switch.
The serial number is 13 digits long. It is printed on the switch label. -
From the PURCHASE DATE menus, select the date that you purchased the switch.
-
Click the REGISTER button.
Your switch is registered to your NETGEAR account.
A confirmation email is sent to your NETGEAR account email address.
Connect the switch
NOTE: Each connected
device requires a power adapter because the MS105 switch does not provide PoE
power.
NOTE: All switch ports support 2.5 Gbps, 1 Gbps, and 100 Mbps. You can
connect any device to any switch port. We recommend that you use Category 5e
(Cat 5e) cables or higher‑rated cables for your connections.
This switch is designed for indoor use only. If you want to connect it to a
device located outdoors, the outdoor device must be properly grounded and
surge protected, and you must install an Ethernet surge protector inline
between the switch and the outdoor device.Failure to do so can damage the
switch.
WARNING: Before connecting this switch to outdoor cables or devices, see
https://kb.netgear.com/000057103 for safety and warranty information.
Check the LEDs
When you connect the power adapter to the switch and plug the cable into an electrical outlet, the LEDs indicate the status:
| LED | Description |
|---|---|
| Power LED |
normally.
| Off. Power is not supplied to the switch.
Both Port LEDs| | Solid green: 2.5 Gbps link on this port.
| Blinking green: 2.5 Gbps activity on this port.
| Off. No link is detected on this port.
Left Port LED only| | Solid green: 1 Gbps link on this port.
| Blinking green: 1 Gbps activity on this port.
| Off. No link is detected on this port.
Right Port LED only| | Solid green: 100 Mbps link on this port.
| Blinking green: 100 Mbps activity on this port.
| Off. No link is detected on this port.
Technical specifications
| Specification | Description |
|---|---|
| Network interfaces | RJ‑45 connectors that support 100BASE‑TX, 1000BASE‑T, and |
2.5GBASE‑Tc
Ports| 5
Power adapter| 12V @ 1A DC input
Maximum power consumption| 7.66W
Hardware security| Kensington slot
Dimensions (W x D x H)| 6.2 x 4.0 x 1.1 in. (158 x 101 x 27 mm)
Weight| 1.1 lb (480 g)
Operating temperature| 32 to 104° F (0 to 40° C)
Operating humidity| 10 to 90% relative humidity, noncondensing
Storage temperature| –4 to 158° F (–20 to 70° C)
Storage humidity| 5 to 95% relative humidity, noncondensing
Maximum operating and storage altitude| 10,000 ft. (3,000 m)
Electromagnetic certifications and compliance| EMC class B device, FCC, ISED,
CE, RCM, VCCI, BSMI, CCC, KC
Safety certifications| CB, CE LVD, BSMI, CCC, RCM
Mount the switch on a wall
We recommend that you use the wall‑mount screws that are included. The screws are 0.25 in. (6.5 mm) in diameter, 0.63 in. (16 mm) in length.
-
Locate the two mounting holes on the bottom panel of the switch.
-
Mark and drill two mounting holes in the wall where you want to mount the switch.
The two mounting holes must be 2.95 in. (75 mm) apart, center‑to‑center. -
Insert the supplied anchors into the wall and tighten the screws with a No. 2 Phillips screwdriver.
Leave about 0.15 in. (4 mm) of each screw protruding from the wall so that you can insert the screws into the holes on the bottom panel.
Support and Community
Visit netgear.com/support to get your questions
answered and access the latest downloads.
You can also check out our NETGEAR Community for helpful advice at
community.netgear.com.
Regulatory and Legal
(If this product is sold in Canada, you can access this document in Canadian
French at https://www.netgear.com/support/download/.)
For regulatory compliance information including the EU Declaration of
Conformity, visit https://www.netgear.com/about/regulatory/.
See the regulatory compliance document before connecting the power supply.
For NETGEAR’s Privacy Policy, visit
https://www.netgear.com/about/privacy‑policy.
By using this device, you are agreeing to NETGEAR’s Terms and Conditions at
https://www.netgear.com/about/terms‑and‑conditions.
If you do not agree, return the device to your place of purchase within your
return period.
Do not use this device outdoors.
Applicable to 6 GHz devices only: Only use the device indoors. The operation
of 6 GHz devices is prohibited on oil platforms, cars, trains, boats, and
aircraft, except that operation of this device is permitted in large aircraft
while flying above 10,000 feet. Operation of transmitters in the 5.925‑7.125
GHz band is prohibited for control of or communications with unmanned aircraft
systems.
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA
NETGEAR INTERNATIONAL LTD
Floor 1, Building 3
University Technology Centre
Curraheen Road, Cork,
T12EF21, Ireland
June 2022
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc.
Any non‑NETGEAR trademarks are used for reference purposes only.
References
- English - NETGEAR Communities
- NETGEAR - Common Account Management
- NETGEAR Support | NETGEAR
- Do I need to use a surge protector with my NETGEAR Business device? - NETGEAR Support
- Download Center | Downloads and Documentation | NETGEAR
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>