KitchenAid Undercounter Refrigerator Manual

UNDERCOUNTER REFRIGERATOR
Solid door
KURR114KSB, KURL114KSB, KURR114KPA, KURL114KPA
Glassdoor
KURR314KSS, KURL314KSS, KURR314KBS, KURL314KBS, KURR214KSB
Detailed Planning Dimensions Guide

Product Dimensions

• Add 5/8” (1.6 cm) to the height dimension when leveling legs are fully extended.
  ** For custom panel models, this will vary.
  † Add 1/4” (6.4 mm) to the height dimension for height with hinge covers.

Because Whirlpool Corporation’s policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with the product.
Specifications are subject to change without notice.

Dimension

| Description| Panel ready models (with 3/4” panel)|

Stainless and black stainless models

---|---|---|---
A| Width of door| 233/4″ (60.3 cm)| 233/4″ (60.3 cm)
B| Width of the grille| 2313/16″ (60.5 cm)| 2313/16″ (60.5 cm)
C| Height to top of the handle|

**

| 311/8″ (78.85 cm)
D| Width from the side of the refrigerator to handle – door open 90°|

**

| 21/3″ (5.95 cm)
E| Depth without door| 2111/16″ (55.1 cm)| 2111/16″ (55.1 cm)
F| Depth with door| 2313/16″ (60.7 cm)| 235/8″ (60.2 cm)
G| Depth with handle|

**

| 267/16″ (67.15 cm)
H| Depth with door open 90°| 4715/16″ (121.8 cm)| 4715/16″ (121.8 cm)

**For custom panel models, this will vary.

Because Whirlpool Corporation’s policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with the product.
Specifications are subject to change without notice.

Opening Dimensions

NOTE: Make sure there is 3” (7.6 cm) space between the refrigerator and adjacent appliance/wall for the door swing.

Electrical Supply Location

• Lighter grey area indicates recommended recessed power outlet (located behind the refrigerator).
• Power cord length is 5 ft (152.4 cm).
• For fl push installation, the power outlet can be installed in adjacent cabinetry with a cutout on the power cord side for routing of the power cord.

Dimensions

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove the ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

A 115 V, 60 Hz, AC only, 15 A or 20 A fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided.
Use an outlet that cannot be turned off by a switch.
Do not use an extension cord.

Because Whirlpool Corporation’s policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with the product.
Specifications are subject to change without notice.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as
gasoline, away from the refrigerator.
Failure to do so can result in death, explosion, or fire.

For the refrigerator to be fl use with the front of the base cabinets, remove any baseboards or moldings from the rear of the opening.
Flooring under product must be at the same level as the room. If the fl more of the opening is not level with the kitchen fl for, shim the opening to make it level with the kitchen fl poor.

Wood Panel Guide

CAUTION: Installation of door panels with less than a 3/8” (0.95 cm) gap between the door panel and the adjacent cabinet increases the risk of potential pinching.

IMPORTANT:

• The graphics in the following sections show a custom panel for a door with the hinges installed on the right-hand side.
  If your refrigerator has the hinges installed on the lefthand side, rotate the custom frame 180° so the hinge markings will be on the left.

Solid door overlay panel

• Panel dimensions shown are the minimum size to cover the appliance door.
  Panels can be made taller/ wider to match surrounding cabinetry.

• The recommended thickness of the overlay panel is 3/4” (19 mm).

• Custom solid door overlay panel must not weigh more than 20 lbs (9.07 kg).

•  Custom glass door overlay panel must not weigh more than 10 lbs (4.54 kg).

• Overlay panels weighing more than recommended may cause damage to your appliance.

Glassdoor overlay panel

®/™ ©2020 All rights reserved. Used under license in Canada.
W11530525
12/2020

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>