BLACK DECKER Power Crush Multi-Function Kitchen System User Manual

: June 7, 2024
: Black Decker

5-IN-1 DIGITAL MULTI-FUNCTION KITCHEN SYSTEM
use and care manual
BL1275BGFP

BLACK DECKER Power Crush Multi-Function Kitchen -

PLEASE READ AND SAVE THIS USE AND CARE BOOK.

IMPORTANT SAFEGUARDS.

When using electrical appliances, always follow basic safety precautions to reduce the risk of fire, electric shock, and/or injury, including the following:

Read all instructions.
To protect against risk of electrical shock, do not put an appliance base, cord or plug in water or other liquid.
Close supervision is necessary when any appliance is used by or near children.
Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or disassembling parts, and before cleaning. To unplug, grasp the plug and pull from the outlet.
Never pull from the power cord.
Avoid contacting moving parts.
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any manner. Contact Customer Service for examination, repair or electrical or mechanical adjustment by calling the appropriate toll-free number listed in this manual. This appliance has important markings on the plug blade. The attachment plug or entire cord set (if the plug is molded onto cord) is not suitable for replacement. If damaged, the appliance must be replaced.
The use of attachments, including canning jars, not recommended or sold by the appliance manufacturer may cause a risk of injury to persons.
Do not use outdoors.
Do not let the cord hang over the edge of the table or counter, or touch hot surfaces.
Keep hands and utensils out of containers while operating appliances to reduce the risk of severe injury to persons or damage to the appliance. A scraper may be used, but must be used only when the appliance is not running.
Blades are sharp. Handle carefully.
To reduce the risk of injury, never place the blades or disc on the base without the blending jar, single-serve blender jar, or work bowl properly attached.
When blending, always operate the appliance with the dual
opening lid in place on the blending jar.
Do not blend hot liquids.
Do not use appliances other than intended use.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not place on or near a hot gas or electric burner or in a heated oven.
Do not operate with damaged blades.
Be certain the work bowl cover is securely locked in place on the work bowl before operating the appliance as a food processor.
This appliance has a protection system. The unit will not operate as a food processor unless the work bowl is on the base and the work bowl cover is securely locked onto the workbowl.
When operating the appliance as a food processor, never feed food by hand. Always use a food pusher.
Do not attempt to defeat the work bowl cover interlock mechanism.
Do not fill the work bowl above the marked maximum fill line to avoid the risk of injury due to damage to the cover or bowl.
Do not open work bowl cover until the blade or disc stops completely.
Note: Processing items with low moisture content may dull the finish of the work bowl.

SAVE THESE INSTRUCTIONS.
This product is for household use only.

POLARIZED PLUG

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way.
If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Do not attempt to modify the plugin anyway.

TAMPER-RESISTANT SCREW

Warning: This appliance is equipped with a tamper-resistant screw to prevent the removal of the outer cover. To reduce the risk of fire or electric shock, do ot attempt to remove the outer cover. There are no user-serviceable parts inside. Repair should be done only by authorized service personnel.

ELECTRICAL CORD

A short power supply cord is provided to reduce the risk resulting from becoming entangled in or tripping over a longer cord.
Extension cords are available and may be used if care is exercised in their use.
If an extension cord is used,
a) The marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance,
b) If the appliance is of the grounded type, the extension cord should be a grounding-type 3-wire cord, and
c) The cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over.
Note: If the power cord is damaged, please call our Customer Service line listed in these instructions.

GETTING TO KNOW YOUR
POWERCRUSH
5-IN-1 DIGITAL MULTI-FUNCTION KITCHEN SYSTEM

1. Dual-opening lid (Part# BL1275-01 )
2. Pour Spout
3. Ingredient Slot
4. Blending jar (Part# BL1275-02)
5. Blade assembly (Part# BL1400-01)
6. Jar base (Part# BL1275-03)
7. Base
8. Digital Control Panel
9. Cord storage (under base)
10. Single-serve jar travel lid
(Part# BL1275-04)| 11. Single-serve jar (Part# BL1275-05)
12. Food pusher (Part # BL1275-06)
13. Feed chute
14. Workbowl cover (Part # BL1275-07)
15. Slicing/shredding disc
(Part # BL1275-08)
16. Chopping blade (Part # BL1275-09)
17. Workbowl (Part # BL1275-10)
18. Center shaft/workbook base assembly (Part # BL1275-11)
---|---

Product may vary slightly from what is illustrated.

HOW TO USE

This product is for household use only.

GETTING STARTED

Remove all packing material, any stickers, and the elastic band around the power plug.
Remove and save literature.
Please visit www.prodprotect.com/blackanddecker to register your warranty.
Wash all removable parts as instructed in the CARE AND CLEANING section of this manual.

BLENDING JAR ASSEMBLY

Turn the blending jar upside down and place flat on the countertop or work surface.
Place the blade assembly in the bottom opening of the jar with blades down. (A)

Caution: Blades are sharp. Handle carefully.

Place the jar base onto the blending jar and rotate clockwise until tight. It is important to tighten to avoid leaking while blending.
Turn assembled jar right side up.
Place the dual-opening lid on the blender jar.
Uncoil power cord from the storage area under the blender base.
Place the jar assembly on the blender base. (B).
The blender is now ready for use.

USING THE BLENDER

Important: Appliance should always have a lid in place when in use.
Caution: Do not place blender jar onto the base when the motor is running.

Make sure the appliance is OFF.
Place ingredients to be blended into jar. For best results, add ingredients in the following order:
a. Liquids
b. Powders
c. Soft foods
d. Hard foods
e. Ice cubes last
Tip: When using frozen fruits it is not necessary to also add ice.
Place lid on jar; make sure the pour spout and ingredient slot are closed.
Plug power cord into the outlet. Press the ON/OFF button. LED should turn a solid color to signify the blender is in standby mode. After 2 ½ minutes, the unit will automatically power off if no buttons are pressed.
Note: When in use, do not leave blender unattended. When using hard foods, such as ice or cheese, keep one hand on the lid to keep the blender in place.
Select the speed that best suits your desired task. (See SPEED CHART) Important: Do not hold the speed button. Simply press the desired speed, watch, and press ON/OFF when the desired consistency is achieved.
Holding the button for longer than 30 seconds will cause the blender to shut off. Unit must be shut off to reset.
When blending thick mixtures, such as smoothies and milkshakes, use the PULSE/Ice Crush button for several seconds, then release. Repeat to mix ingredients and then run continuously until the food has reached desired consistency. Releasing pulse stops the blending and the unit returns to STANDBY. You may use a spatula or utensil to move ingredients and thick mixtures around in the blender jar, but only after stopping the blender. Turn the blender OFF before using a utensil.
Open the ingredient slot to add ingredients while the blender is running. Drop ingredients through the opening. (C).

Important: Do not remove the lid while the blender is running.

When finished, press ON/OFF to stop blending. Make sure blades have completely stopped before attempting to remove the blending jar from the base (refer to TROUBLESHOOTING for any issues).
Press ON/OFF to power off and unplug the blender.
To remove the jar, grasp the handle and lift up.
Open pour spout to serve.
Note: Unit will auto shut off after 2 ½ minutes without use.
Always unplug the appliance when not in use.

USING THE PREPROGRAMMED FUNCTIONS

Fill the assembled blender jar with the desired ingredients.
Place the dual-opening lid on the jar.
Place the jar on the base.
Press desired preprogrammed button. The blender will automatically mix and blend the following recipes with the press of a button:
– Smoothie: 30 seconds to blend fruits and vegetables to a smooth consistency.
– Icy drinks: Perfect for classic icy drinks like Margaritas with small ice crystals.

USING THE SINGLE-SERVE BLENDER JAR

Note: Do not blend hot liquids in the single-serve jar.

Place the single-serve blender jar on a flat surface with the open end facing up. Fill the jar with ingredients. Do not fill ingredients past the Max fill line.
Note: For best results, add ingredients in the following order:
a. Liquids
b. Ice
c. Hard Foods
d. Soft Foods
e. Powders
Place blade assembly in the jar opening with blades down.
Place jar base onto the jar and rotate clockwise until it is tight. It is important to tighten to prevent leaking during blending.
Turn the single-serve jar upside down and place it on the blender base.
Select speed 1 or use PULSE/Ice Crush to blend to desired consistency.
While blending, keep one hand holding the single-serve jar.
Once blending has finished, remove the single-serve jar by lifting it off the base. Turn the jar over and place it on a flat surface.
Note: Always make sure blades have stopped moving before removing the jar.
Important: If the jar gets stuck on the blending base or begins to loosen from the jar base, follow these steps:
a. Unplug the unit
b. Turn the jar clockwise to tighten the jar onto the jar base
Remove the jar base from the single-serve jar by turning counterclockwise. Then carefully remove the blade assembly
Place the single-serve jar drinking lid on the single-serve jar and enjoy your delicious drinks on the go.
Caution: Blades are sharp. Handle carefully.

BLENDING TIPS AND TECHNIQUES

Cut food into pieces no larger than ¾” for use in the blender.
When preparing foods that have several different kinds of ingredients, always add liquid ingredients first.
When ingredients splatter onto the sides of the jar or the mixture is very thick, press the ON/OFF button to turn the appliance off. Remove the lid and use a rubber spatula to scrape down the sides of the jar and to redistribute the food, pushing food toward the blades. Replace the lid and continue blending.
When making bread crumbs or blending dry goods, make sure blending jar and blade assembly are completely dry.
The PULSE/ICE CRUSH function is helpful when short bursts of power are needed, such as when preparing thick smoothies or milkshakes. Do not use pulse for more than 10 seconds at a time. Release the PULSE/ICE CRUSH button regularly, allow the blender to rest briefly, then continue.
Do not run the blender for longer than 1 ½ minutes at a time.
Do not use if the blender jar is chipped or cracked.
It is helpful to begin the blending process on the lowest speed and then increase to a higher speed, if necessary.
To stop blending at any time, press the ON/OFF button.
Always operate the blender with the lid on the jar.
Do not store foods in the blending jar.
Do not overfill the blender (the blender is more efficient with less rather than more).

DO NOT USE A BLENDER TO BLEND:

Large pieces of frozen foods
Tough foods such as raw turnips, sweet potatoes, and potatoes
Bones
Hard salami, pepperoni
Boiling liquids (cool for 5 minutes before place in blending jar)
Egg whites
Dough
Meats

SPEED AND FUNCTION CHART

Function	Food Type	Speed Setting
1	Stir Mix Crumb	Prepare salad dressings.

Mix ingredients for baked goods. Make crumbs: cookie, cereal, bread. Blend in the single-serve jar.
2| Chop Whip Blend| Chop fruits, vegetables.
Whip whipped cream or butter. Blend smoothies, sauces
3| Dressings Batters
Dips| Puree fruits and vegetables. Blend milkshakes and malts. Grind hard cheeses and coconut.
Pulse/Ice Crush| Pulse Ice| Pulse to desired consistency. Crush ice to snow texture.
30 Second Smoothie| Smoothies| Preset function
Icy Drinks| Margaritas Daiquiris| Preset function

ASSEMBLING THE FOOD PROCESSOR ATTACHMENT

Important: Always make sure the base of the appliance is unplugged and placed on a flat, level surface before starting to assemble.
Important: For your protection, this appliance has an interlock system. The appliance will not operate as a food processor unless the cover is properly locked in place.

Lower workbook over center shaft/work bowls base assembly and rotate bowl clockwise to lock the two parts together.
Place either the chopping blade or the slicing/ shredding disc onto the center shaft.
Place cover on work bowl with the latch closest to the feed chute counterclockwise from the latch to the right of the work bowls handle. Line up the pin on the lid with the pin on the center shaft.
Gently press down the lid to depress the lower pin and rotate the cover clockwise until cover locks into place.
Place work bowl onto base and twist clockwise to lock.

GENERAL TIPS FOR

USING THE FOOD PROCESSOR ATTACHMENT

Organize processing tasks to avoid multiple cleanups of the bowl; process dry before wet.
Do not process foods that are so frozen or hard that the tip of a knife cannot be inserted into the food.
If a piece of hard food, such as a carrot, becomes wedged or stuck on the blade, stop the appliance and unplug, then remove the blade. Gently remove food from the blade.
Meat and cheese should be well chilled before slicing or shredding.
Insert a funnel into the feed chute when adding ingredients such as, oil, flour, and sugar.
Do not use the food processor attachment to:
– Grind coffee beans, bones, grains or hard spices
– Slice or chop warm meat

TIPS FOR USING THE CHOPPING BLADE

The chopping blade works very quickly. Watch carefully to avoid overprocessing foods.
For best results, process foods that are about the same size.
The appliance will be more efficient if workbook is filled no more than 1/2 to 2/3 full.
Processing nuts or other hard foods may scratch the surface finish on the inside of the work bowl.
Never walk away from the appliance while it is on.
Use hot, but never boiling liquids.
The PULSE feature offers the best control.

TIPS FOR SLICING OR SHREDDING

Before slicing round fruits and vegetables with the disc, cut a thin slice from the bottom so food will be more stable. Place food cut side down in the feed chute.
Always remove seeds, core, and pits before processing
Select foods that are firm and not overripe.
When slicing thinner vegetables cut them just short of the length of the feed chute; stand them vertically in the feed chute so they are solidly packed and cannot turn or tilt.
Soft and semi-hard cheeses should be well chilled before shredding.
Do not let the food accumulate too high (over 2/3 full); stop and empty the work bowl.

WHAT SPEED TO USE

CARE AND CLEANING

This product contains no user-serviceable parts. Refer service to qualified service personnel.

Before cleaning, turn off and unplug the appliance.
If using a blending jar, lift the blending jar by the handle off the base.
Remove jar base by turning it counterclockwise until loose.
Remove the blade assembly.
Caution: Blades are sharp. Handle carefull y.
Remove lid.
Wash removable parts by hand or in the dishwasher. Place the jar on the bottom rack and the rest of the parts on the top rack only.

Rinse removable parts immediately after using the appliance for easier cleaning.
Completely disassemble blender or food processor attachment parts before washing.
All removable parts can be washed by hand in hot water with dish soap or in the dishwasher, top rack only. Hand-washing of plastic parts will help to maintain the appliance’s appearance.
Do not use rough scouring pads or cleansers on any plastic or metal parts to clean.
Do not allow the blade or disc to soak in water for long periods of time.
Remember to clean the internal shaft of the chopping blade. Use a brush to remove any residual food particles.

Important:

Do not place the parts in boiling liquids.
Do not immerse the base in liquid. Wipe the base with a damp cloth and dry thoroughly.
Remove stubborn spots by rubbing with a damp cloth and non-abrasive cleaner.
Note: If liquids spill onto the base, wipe with a damp cloth and dry thoroughly.
Do not use rough scouring pads or cleansers on parts or finish.

TROUBLESHOOTING

Problem	Possible Cause	Solution
Blender is having difficulty blending	The mixture is too thick or air bubble
has formed between the mixture and blade.	Turn blender off. Use a rubber

spatula to scrape down sides of the jar and redistribute, pushing food towards blades. Add more liquid.
Blender stops/ goes into STANDBY mode| Blending time exceeds 2.5 minutes.| Re- select the appropriate speed setting to start the blender.

RECIPES

CLASSIC SMOOTHIE
4 cups apple juice
4 medium bananas, cut into 2 pieces
4 cups frozen whole strawberries
Place ingredients in blender in the order shown above. Cover and blend for 15 seconds, or until smooth.
Makes 6 (1 cup) servings
Tip: Substitute orange juice for apple juice

EASY FROZEN MARGARITA
½ cup orange-flavored liquor
1 cup tequila
1 (6 oz.) can freeze limeade mix
4 cups ice cubes
Place ingredients in a blender with liquids first and ice last; cover. Blend on
AUTO setting ICE DRINK. Serve with lime wedges if desired.
Makes 6 servings

SIMPLE SALSA
Total Time: 5 minutes
Servings: makes 2 cups

Ingredients

2 medium fresh tomatoes, quartered
1/3 cup loosely packed cilantro
1/ 3 cup diced tomatoes and green chilies*
1/4 small yellow onion
1 tsp. minced garlic| 2 Tbsp. fresh lime juice
1/2 tsp. salt
1/2 tsp. sugar
1/ 2 stem and seeds removed (optional)
---|---

Directions

Place the tomatoes into the food processor attachment work bowl with the chopping blade and pulse 4 to 5 times to chop.
Add the remaining ingredients into the bowl with the chopped tomatoes and process on Low (speed 1) for about 30 seconds, or until desired consistency
is reached.
Serve with tortilla chips.
*Look for cans of diced tomatoes with green chilies in the Mexican or International section of the grocery store.

BLACK BEAN HUMMUS
Total Time: 5 minutes
Servings: 7
Serving Size: 1/4 cup

Directions

Preheat oven or toaster oven to 350°F.
In the food processor attachment work bowl with the chopping blade, place the seeded in and pulse 3 to 4 times to dice.
Put the remaining ingredients and 1 3/4 cup of the shredded cheese into the bowl with the diced jalapeño. A process on High for about 30 seconds to reach a smooth consistency.
Pour the mixture into an oven-safe dish and smooth out. Top with the remaining 1/2 cup shredded cheese.
Bake for 15–20 minutes until the cheese is bubbly.
Serve with tortilla chips or crackers.

All other marks are Trademarks of Spectrum Brands, Inc.
Todas la demás marcas son Marcas Registradas de Spectrum Brands, Inc.

Made in China.
Fabricado en China.

T22-5004260-C

E/S 27431