LIGHTSOUNDS 1x200W COB LED Spotlight User Manual
- June 7, 2024
- LIGHTSOUNDS
Table of Contents
1x200W COB LED SPOTLIGHT
User’s Manual
Thanks for using our products. For your safety, please read the User’s Manual
carefully before your operation.
This Manual includes important information on installation, operation, safety
instructions. Please install and operate as requested in the Manual,
meanwhile, please keep the manual for any unexpected requirements.
inspection of the light must be made by the authorized electrical engineer every three months.
Preface
This Manual includes important information of installation and operation. In
order to make sure the correct and safe installation, operation and
maintenance,
well know and follow to the instructions of Manual is necessary. Please keep
the manual for any unexpected requirements. We will not take any
responsibility to the light damage 、property loss or body injure caused by
incorrect installation, operation and maintenance.
NOTICE The data inside the Manual may be changed due to continuous
improvement, and we’ll not make another notice. We will keep the right to any
specification update during improvement
Packing Content
- The Light (1PCS)
- Power cable(1PCS)
- Signal Cable（1PCS ）
- User’s Manual （1PCS ）
Please check if all the contents are completed after unpacking？ then, check if the light is undamaged？ Please you can keep the original package and return to the factory if it’s damaged
Safety information
- This product is only operated by adults; please put it where the child can not touch it.
- Please check if the voltage is in accordance with the rated power or not before installation, and please note the total electric circuit load.
- This device is for indoor use only, the light must be kept dry and avoided to use under the Moist, Overheat, or Dusty surroundings. If there is any water or other liquid in the product, please cut off the power and contact your supplier.
- Make sure that the power cable does not shrink volume and the insulation cover of the power cable will not be scratched by anything sharp.
- Please cut off power when doesn’t use or before cleaning, maintenance the light.
- The light doesn’t include any spare parts for repair. In order to avoid danger, please do not open and change the product structure by yourself.
Operation
Control Panel
A ．MEUN
B ．UP
C．DOWN
D ．ENTER
Menu Function Settings
| No. | Display | Function |
|---|---|---|
| 1 | DMX-ADDR 001 | DMX address |
| 2 | R-DIMMER 255 | LED Dimmer 0-255 |
| 3 | P-STROBE 255 | LED Strobe 0255 |
| 4 | DMX-KEEP ON/OFF | DMX signal to keep |
| 5 | Now temp | Lamp bead temperature |
The usage and match of signal cable and XLR connector
A.DMX mode: Connect the signal cable from the DMX output of the controller to
the input of the first light, and connect to the DMX input of second light
from the DMX output of the first master light, analogously ，till connected all
the slave lights, and insert the last connector to the output of the final
light.
B.Master and slave mode: Connect the signal cable from the DMX output of the
first master light, and connect to the DMX input of the second slave light
from the DMX output of the first master light, analogously，till connected all
the slave lights, and insert the last connector to the output of the final
light. For the master and slave mode settings, please refer to the function
settings above.
Notice: there is only one master in the one circle connection, all the
lights cannot connect to the controller, otherwise, there will be confusion
for slave light.
DMX Address Settings
Each light should be set with a particular starting address code. According to
the actual requirements or easy to use, users can either set multiple lamps
with the same address code; also can set each lamp with an independent address
code.
Setting multiple lamps with the same address code, then they will all accept
DMX512 channel signals start from a same address code. Thus, all connected
lamps will be controlled together.
Setting each lamp with a different address code, the next light’s DMX address
is depend on the light DMX channels.
DMX Channel
2CH
| No. | Function | Description |
|---|---|---|
| 1CH | Dimming | Form dark to bright |
| 2CH | Strobe | Strobe Form slow to fast |
Cleaning & Maintenance
Clean the product frequently, it can keep the output brightness and extend the product life
warning： It must be power off before cleaning or maintenance of the light.
-
Product cleaning
A.Clean the output acrylic board and product body every 2 weeks, or smoke dust accumulation will weaken the brightness of the light.
B.Use soft cloth with water to clean, do not with an organic solvent, such as ethyl alcohol
C.Clean the cool fan each month -
Product maintenance
Product maintenance must consider the below terms.
A.All screws mounted on the lamp must be reliably tightened, check and replace the corroded screws.
B.Ensure fixed point for installation without any deformation
C.Check if the power cable is damaged, and if the insulation layer is worn down.
D.To ensure the good connection of the various parts of the circuit, and to avoid unnecessary accidents coursed by bad electrical connections, the detailed inspection of the light must be made by the authorized electrical engineer every three months.
Technology Parameters
Power supply： AC100-240V,50Hz-60Hz
Power consumption：200W
Light source：1x200W Warm White COB(Cool white Optional)
LifeTime：50000 hours
Beam angle：15°~50°
Brightness：6063LUX on 4 meters distance
Color temperature ：3200K / 5600K
CRI ：>80
Control panel： LCD display+ 4 soft keys
Controls mode： Master/Slave ，DMX512 DMX
channels：2 CHS
Dimmer：0~100% linearly adjustable
Strobe ：electronic strobe,1-30times/sec
Working environment： up to 40°C
Protection rate： IP20
Cover： Aluminum
Dimension size：510×295×265mm
Packing size ：480x345x295mm
N.W ：8.2kg
G.W：9.4kg
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>