SCHWAIGER 661828 RGB LED Solar Outdoor Floor Lamp with Bluetooth Speaker Instruction Manual

SCHWAIGER 661828 RGB LED Solar Outdoor Floor Lamp with Bluetooth Speaker

Product Information

The OS-150 is a multi-functional LED lamp that also functions as a speaker. It comes with a remote control that allows for easy adjustment of the lamp’s brightness, color temperature, and color selection. The lamp also has a built- in rechargeable battery that can be charged via USB or solar panel. The product is intended for indoor use only and has an IP44 rating for water resistance.

Technical Specifications

• Model: OS-150
• Article Number: 661828
• LEDs: 12x RGB LED
• Lamp Power: 2.16W
• Battery: 3.7V DC 2,200mAh Lithium-Ion
• Ladespannung Solarpanel: 6V DC, 250mA, 1.5W (Poly Crystal)
• Charging Voltage: 5V DC, 1A
• Bluetooth Version: V5.0
• Speaker Power: 2x 5W
• Bluetooth Frequency Range: 2400 – 2483.5 MHz
• Bluetooth Transmitting Power: 1.64 mW (Class III)
• Color Temperature: 3000K
• Luminous Flux: 200lm
• Lifetime: Approximately 50,000 hours
• Number of Switching Cycles: 50,000
• Dimmable: Yes, with remote control
• Dimensions: 30cm x 30cm
• Battery Type: CR2025 3V Knopfzelle (included)

Product Usage Instructions

Before using the OS-150 for the first time, it is recommended to fully charge the battery. The lamp can be charged via USB or solar panel. Follow the steps below for charging and using the lamp:

1. Charging:
   • Connect the USB charging cable to the charging port on the back of the lamp and plug the other end into a power source with a voltage of 5V DC and current of 1A.
   • The battery slider should be in the “ON” position during charging.
   • The lamp will be fully charged after approximately 4 hours of charging.
   • Alternatively, you can charge the lamp using the built-in solar panel. Place the lamp in direct sunlight and ensure that the solar panel is facing upwards.
2. Using the Lamp:
   • Press the “ON/OFF” button on the remote control to turn on/off the lamp.
   • Use the “Brightness” button to adjust the brightness of the lamp.
   • Press the “Warm White” button to adjust the color temperature between warm white and cool white.
   • Use the “Color Selection” button to select a specific color for the lamp.
   • Press the “/” and “<<” buttons to cycle through different colors.
   • Use the “Ausschalt-Timer” button to set a timer for the lamp to turn off automatically after 30, 60, 90, 120, 150, or 180 minutes.
   • Press the “Music Control” buttons to play, pause, skip, or rewind music playing through the built-in speaker.
   • Use the “Smooth” and “Time” buttons to adjust the smoothness of color transitions and speed of color changes.
3. Cleaning:
   • Before cleaning the lamp, ensure that it is turned off and unplugged from any power source.
   • Use a soft, damp cloth to clean the lamp. Do not use any harsh chemicals or abrasive materials.
4. Disposal:
   • Do not dispose of the OS-150 with regular household waste. Follow local regulations for disposing of electronic devices.
   • The battery should be removed and disposed of separately from the lamp.

COMPONENTS

1. Lampshade
2. Speaker, 2x
3. Stand tube, 3x
4. Support
5. USB charging cable
6. Charging port
7. On / Off
8. Solar panel
9. Increase brightness button
10. Reduce brightness button
11. LED on/off button
12. Bluetooth® on/off button
13. Switch through colours button
14. Colour white button
15. Cool white colour temperature button
16. FLASH button
17. TIME button
18. SMOOTH button
19. Music control buttons
20. Warm white colour temperature button
21. Colour selection button
22. Battery slider

GENERAL

Reading operating instructions and keeping them in a safe placeThese operating instructions belong to the outdoor solar stand lamp, hereinafter referred to as the product. They contain important information on handling the product and putting it into use. Read through the operating instructions carefully, including the safety instructions, before using the product. Non-compliance with these operating instructions may cause serious injury and damage to the product. The operating instructions are based on the applicable European Union standards and regulations. Also observe your country’s specific guidelines and laws. Keep the operating instructions in a safe place ready for use at a later stage. If you pass the product on to a third party, you must give them these operating instructions too.

Intended use
The product is designed exclusively to provide ambient lighting indoors and outdoors and reproduce audio signals transmitted via Bluetooth® by a source device. It is meant for private use only and not for commercial purposes. Please follow these instructions carefully. Any other use is considered improper use and may cause damage.

General safety instructions
WARNING:
Risk of Electric Shock!
Faulty electrical installation or excessive mains voltage can lead to electric shock.

• When using the USB charger, only connect it if the socket network voltage is the same as the voltage indicated on the nameplate.
• Only use power supplies that comply with the SELV standard as per IEC 61558-2-6 or IEC 61347-2-13 or ES1/IEC 62368-1 as per IEC 62368-3 to charge the installed Li-ion battery.
• Do not use the product if it is visible damaged or the USB charging cable is defective.
• Do not open the casing. Leave repairs to qualified persons. Contact a specialist workshop in such cases. Liability and warranty claims are excluded if customers repair the product themselves, connect it improperly or operate it incorrectly.
• Only parts that meet the original device specifications may be used for repairs. This product contains electric and mechanical parts which are essential to protect against sources of danger.
• Do not operate the product with an external timer switch or a separate telecontrol system.
• Do not immerse the product or the USB charging cable in water or any other liquid.
• Never touch the USB connector when your hands are wet or damp.
• Never pull on the USB charging cable to remove the USB connector from the charging socket; always pull on the USB connector itself.
• Never use the USB charging cable as a carrying handle.
• Keep the product and USB charging cable away from open fire and hot surfaces.
• Position the USB charging cable in a place where no-one will trip on it.
• Do not kink the USB charging cable and do not place it over sharp edges.
• Never operate the product in damp rooms or in the rain.
• Never place the product in a position where it may fall into a pond, pool or similar.
• Never take hold of an electrical device which has fallen into the water. Remove the USB charger from the charging socket immediately in such cases.
• Do not expose the product to rain or extreme weather conditions, such as sub-zero temperatures, hail or extreme heat.
• Charge the product indoors.
• Ensure that no fluids get into the product; dry the product thoroughly if necessary before using it again.
• Ensure that children do not insert any objects into the product.
• Always switch the product off and disconnect the USB charging cable from the charging socket when you are not using the product, when you clean it or if it has a fault.

WARNING:
There are dangers for children and persons with reduced physical, sensory or mental abilities (e.g. partially disabled persons, elderly persons with limited physical and mental abilities) or lack of experience and knowledge (e.g. older children).

• Children above the age of eight and people with reduced physical, sensory or mental capabilities or lacking in experience and knowledge may only use the product under supervision or if they undergo a suitable briefing on the safe use of the product and they are aware of the associated risks and hazards. Do not allow children to play with the unit. Do not allow children to clean or maintain the radio without supervision.
• Keep children under eight years of age away from the product and the connecting cable.
• Do not leave the product unattended while it is in operation.
• Do not let children play with the packaging film. Children can get caught in the film and suffocate while playing.
• Keep children away from the remote control and the battery it contains. Children might put the battery in their mouth and then choke and/or suffer chemical burns.

WARNING:
Fire hazard!
Handling the product and battery improperly may cause a fire or an explosion.

• Keep the product away from water, other liquids, open fires and hot surfaces.
• Do not cover the product or the USB charging cable with objects or clothing.
• Keep the product at a distance of at least 5 cm from easily inflammable materials.
• Charge the product with the supplied accessories only.

WARNING:
Hazards caused by batteries!
If you use batteries improperly, there is a danger of explosion or chemical burns due to battery fluid leaking.

• Do not throw batteries into a fire. They may explode or emit toxic vapours.
• Do not expose batteries to sustained direct sunlight and heat. High risk of leakage!
• Do not charge batteries, do not take them to pieces and do not short-circuit them. Risk of explosion!
• Remove the battery from the battery compartment when it is flat or if you are not going to use the product for a longer period of time.
• Ensure correct polarity when inserting the battery.
• Use batteries of the same type only.
• Clean the battery and device contacts if needed before inserting the battery.
• Ensure that the product is switched off after use.
• Consult a doctor immediately if you suspect someone has swallowed a battery or it has entered the body in any other way.
• Do not touch leaked batteries. If you do happen to come into contact with battery fluid, wash the affected area thoroughly with plenty of clean water. Also seek medical help if leaking battery fluid causes a skin reaction or gets into eyes.
• Do not use the product any longer if the battery compartment housing the battery no longer closes securely. Remove the battery and put it in a safe place out of children‘s reach.

CAUTION:
Risk of injury!
The light from the LED light is strong and can damage the eyes if you look into it from insufficient distance.

• Never look into a lit LED lamp at close distance.
• Never examine a lit LED lamp with a magnifying glass or any other optical instruments.

CAUTION:
Risk of injury!
Listening to music at a continuous high volume can cause damage to hearing.

• Prevent damage to health and avoid listening to music at a high volume for long periods of time.
• Always keep an adequate distance from the product at high volume levels and never place your ears directly against the speaker.

NOTE: Risk of damage!
Handling the product improperly can lead to damage to the product.

• Position the product on a dry, level, heat-resistant, easily accessible, sufficiently stable working surface. Do not position the product on the edge of the working surface.
• Never position the product on or near to hot surfaces, such as hot plates or cooktops.
• Do not bring the product or the USB charging cable into contact with hot components.
• Never expose the product to high temperatures (heating and similar) or the weather (rain, etc.).
• Never pour liquid into the product.
• Never immerse the product in water to clean it and do not use steam cleaners to clean. The product can otherwise become damaged.
• Do not use the product any longer if its plastic components are cracked or have become warped. Replace damaged components with original spare parts only.
• The product’s illuminant cannot be replaced. Replace the entire product when the illuminant has reached the end of its service life.

INITIAL OPERATION

Checking product and supplied package

NOTE:
Risk of damage!
The product can become quickly damaged if you do not take care when opening the packaging with a sharp knife or other sharp objects.

• Open the packaging very carefully.
  1. Remove the product from the packaging.
  2. Check that the supply package is complete.
  3. Check that the product or individual parts are not damaged. If anything is damaged, do not use the product. Contact the hotline or e-mail address given in this operating manual.

Assembling product

1. Screw the three stand tubes 3 together.
2. Screw the assembled stand tubes into the base 4 .
3. Screw the lamp shade 1 onto the assembled stand tubes.

Putting remote control into use
A contact protection film is placed in the battery compartment, which must be removed before the lamp is used for the first time.

• Pull the contact protection film from the remote control battery compartment.

Replacing battery

1. Push the battery slider pressure latch towards 22 the battery slider.
2. Pull the battery slider out of the remote control at the same time.
3. Remove the flat battery.
4. Replace the flat battery with a battery of the same type (see Technical specifications section) and ensure the polarity is correct. The plus terminal position is indicated on the rear of the remote control.
5. Insert the battery slider with the new battery into the remote control.

Charging the product
Charge the product fully before using it for the first time.

Charging with the USB charging cable

NOTE:
Risk of damage!
Charging the product with an unsuitable USB charger can damage the product.

• Only use chargers with a max. output voltage of 5 V to charge the product.

1. Place the product on a dry, horizontal surface before charging.
2. Unwind the USB charging cable 5 completely.
3. Plug the USB type C connector into the charging socket 6 .
4. Plug the USB connector into a USB power source, such as a USB charger. During the charging process, the control lamp lights up red. The charging time is about 4-6 hours. The control light will turn green once the product is fully charged. You can then use the product.

Charging with the solar panel

1. Place the product outdoors.
2. Ensure the product is not in the shade.
3. Let it charge from the solar panel 8 in direct sunlight for about 10 hours.
   The charging time depends on the light intensity. It can be slower if it is cloudy.

INSTRUCTIONS

• Press the on-off switch 7 to switch the product on. You will hear a confirmation tone.
• Press the on-off switch again to switch the product off.

Description of button functions

LAMP CONTROL

Switching light on/off

• Press the LED on/off button to switch the LED function on or off 11 .

Setting light colour

• Press the increase brightness button 9 or reduce brightness button 10 to increase or reduce light intensity.
• Press the colour white button to set the light colour to white 14 .
• Press the corresponding button to select the colour to set another light colour 21 .
• Press the colours button to switch through the colours one after another 13 .
• Press the SMOOTH button 18 to fade colours into one another continuously.
• Press the FLASH button 16 to synchronise the light rhythm with the music played.

Setting the colour temperature

• Press the cool white colour temperature to set the colour temperature to cool white 15 .
• Press the warm white colour temperature to set the colour temperature to warm white 20 .

Setting the switch-off timer
You can set the switch-off timer in such a way that the product switches off automatically after a certain time.

• Press the TIME button 17 to set the switch-off timer. The light colour changes to red and the switch-off timer is set to 30 minutes. The switch-off time increases every time you press the TIME button. The table below shows the colour and the associated switch-off time.

The switch-off timer can only be switched off if you press the on/off switch 7 and switch off the product.

Connection via Bluetooth®
You first need to interconnect devices with one another if you wish to transmit sound from your audio player, such as a smartphone, via Bluetooth®.

1. Switch on the Bluetooth® function on your audio player.
2. Press the Bluetooth® on/off button. 12 . You will hear a confirmation tone.
3. Wait for your audio player/smartphone to search for Bluetooth® devices. You will find more information on connecting devices in the operating instructions for your audio player. “Solar-Aussenstehleucht” should appear in the list of discovered devices after the search.
4. Select “Solar-Aussenstehleucht” from the list of discovered devices. You will hear another confirmation tone. Connection is thus complete and your product now works as a Bluetooth® playback device. The product will now reproduce all sounds that your audio player/smartphone can play.
5. Press on the Bluetooth® on/off button again to remove the connection 12.

Music control
You can use the buttons for music control 19 to control music playback and the volume with the remote control. The music is emitted via the loudspeaker 2 .

• Press the button to pause or continue reproduction.
• Press / to skip back or forward a track.
• Press the / button to increase or reduce the volume.

CLEANING

NOTE:
Danger of short-circuit!
Any water or other liquids which penetrate the casing may cause a short circuit.

• Never immerse the product in water or other liquids.
• Ensure that no water or other liquids penetrate the casing.

NOTE:
Risk of damage!
Handling the product improperly can lead to damage to the product.

• Do not use any aggressive cleaning agents, brushes with metal or nylon bristles or any sharp or metal cleaning objects such as a knife, hard scraper and similar since these may damage the surfaces.
  1. Switch the product off before cleaning.
  2. Clean the product with a soft, dry cloth.
  3. Use a slightly dampened cloth and, where necessary, a little mild dishwashing detergent to clean stubborn stains.
  4. Then leave all components to dry completely.

Storage
All components must be completely dry before putting them away.

• Always store the product in a dry place.
• Store the product out of children’s reach in a securely locked place and at a storage temperature between 5 °C and 20 °C (room temperature).

Technical data

Simplified declaration of conformity as per the RED Directive
Schwaiger GmbH hereby declares that the described radio system product complies with Directive 2014/53/ EU and other directives applicable to the product. The complete EU declaration of conformity is available online at: http://download.schwaiger.de

Disposal
Do not dispose of batteries or electric and electronic devices in the normal household waste. The consumer is legally obliged to return electrical and electronic devices and batteries that are at the end of their useful life to the point of sale or public collection points that have been set up for this purpose. Legislation in the country of use governs individual details regarding disposal. The symbol on the product, the user guide or the packaging indicates this legal requirement.
Disclaimer
Schwaiger GmbH does not accept any liability or warranty for damages that are sustained due to improper installation or mounting, improper use of the product or non-compliance with the safety instructions.
Manufacturer‘s information
Dear Customer,
Please contact our Technical Support if you need technical advice and your retailer is unable to help you.

Warranty
The warranty period starts when the product is purchased. The purchase receipt, such as a till receipt, invoice or delivery slip, serves as proof of this date. Keep these documents in a safe place. Our warranty is based on our warranty conditions valid at the time of purchase.
Office Hours (Technical Support in German) Monday to Friday: 8:00 a.m. – 5:00 p.m.

HOTLINE
+49 (09101) 702-299
Anschrift
Schwaiger GmbH
Würzburger Straße 17
90579 Langenzenn
info@schwaiger.de
www.schwaiger.de
Irrtümer, Abweichungen und Änderungen bei den technischen Angaben und Abbildungen vorbehalten.

References

• Schwaiger GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>