PowerDynomics FCS Series LowProfile Ceiling Speaker 100V Instructions
- June 7, 2024
- PowerDynomics
Table of Contents
FCS Series LowProfile Ceiling Speaker 100V
Ref. nr.: 952.546, 952.548, 952.549
INSTRUCTION MANUAL
Congratulations on the purchase of this Power Dynamics product. Please read
this manual thoroughly prior to using the unit in order to benefit fully from
all features.
Read the manual prior to using the unit. Follow the instructions in order not
to invalidate the warranty. Take all precautions to avoid fire and/or
electrical shock. Repairs must only be carried out by a qualified technician
in order to avoid electrical shock. Keep the manual for future reference.
– The unit contains voltage carrying parts. Therefore do NOT open the housing.
– Do not place metal objects or pour liquids into the unit This may cause
electrical shock and malfunction.
– Do not place the unit near heat sources such as radiators, etc. Do not place
the unit on a vibrating surface. Do not cover the ventilation holes.
– The unit is not suitable for continuous use.
– If the plug and/or the mains lead are damaged, they need to be replaced by a
qualified technician.
– If the unit is damaged to such an extent that internal parts are visible, do
NOT plug the unit into a mains outlet and DO NOT switch the unit on. Contact
your dealer.
– To avoid fire and shock hazards, do not expose the unit to rain and
moisture.
– All repairs should be carried out by a qualified technician only.
– If the unit has not been used for a longer period of time, condensation may
occur. Let the unit reach room temperature before you switch it on. Never use
the unit in humid rooms or outdoors.
– To prevent accidents in companies, you must follow the application
guidelines and follow the instructions.
– Keep the unit out of the reach of children. Do not leave the unit
unattended.
– Do not use cleaning sprays to clean switches. The residues of these sprays
cause deposits of dust and grease. In case of malfunction, always seek advice
from a specialist.
– Do not force the controls.
– This unit is with a speaker inside which can cause a magnetic field. Keep
this unit at least 60cm away from the computer or TV.
– If the unit has fallen, always have it checked by a qualified technician
before you switch the unit on again.
– Do not use chemicals to clean the unit. They damage the varnish. Only clean
the unit with a dry cloth.
– Keep away from electronic equipment that may cause interference.
– Only use original spares for repairs, otherwise serious damage and/or
dangerous radiation may occur.
– Switch the unit off prior to unplugging it from the mains and/or other
equipment. Unplug all leads and cables prior to moving the unit.
– Keep the original packing material so that you can transport the unit in
safe conditions.
This mark attracts the attention of the user to high voltages that are present
inside the housing and that are of sufficient magnitude to cause a shock
hazard.
This mark attracts the attention of the user to important instructions that
are contained in the manual and that he should read and adhere to.
The unit has been certified CE. It is prohibited to make any changes to the
unit. They would invalidate the CE certificate and their guarantee!
NOTE: To make sure that the unit will function normally, it must be used
in rooms with a temperature between 5°C/41°F and 35°C/95°F.
Electric products must not be put into household waste. Please bring them to a
recycling center. Ask your local authorities or your dealer about the way to
proceed. The specifications are typical. The actual values can slightly change
from one unit to the other. Specifications can be changed without prior
notice.
Do not attempt to make any repairs yourself. This would invalidate your warranty. Do not make any changes to the unit. This would also invalidate your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use or disrespect of the warnings contained in this manual. Power Dynamics cannot be held responsible for personal injuries caused by the disrespect of the safety recommendations and warnings. This is also applicable to all damages in whatever form.
INSTALLATION
This speaker for ceiling mounting is a 100 Volt system specially designed for
application in PA systems and must only be used for permanent installations,
to be connected with an appropriate 100V-amplifier.
- Drill a hole in the ceiling, big enough to fit the speaker (check technical specification sheet for size).
- If the PA system is turned on, turn it off before making any connection.
- Connect the speaker via two cables to the 100Vor 8 Ohm output of the amplifier (see below for a connection overview); when connecting several speakers, make sure that all speakers have the same polarity and that the amplifier is not overloaded. Before starting with the installation, you must clarify how many speakers you would like to install in the room
- Make sure to set the jumper in the correct setting for desired use (100V or 8 Ohm)
- Insert the speaker in the hole
- Screw down each of the screws (the locking tabs will swivel into the rear surface)
- Place the metal grill
OPERATION
Procedure:
Step 1: If the 100Volt system is turned on, turn it off before connecting.
Step 2: Connect the speaker(s) to the 100V or 8 Ohm amplifier output, using a two-core suitable cable. For the wiring diagram, see further in this manual.
Always insulate the unused connection cables.
Step 3: If you are connecting multiple speakers, make sure that all speakers have the same polarity and that the amplifier is not overloaded.
Always make sure that the output signal is not distorted and that your
speakers will not get damaged.
When distortions can be heard, either the amplifier or the speaker is
overloaded. In order to avoid damage, reduce the volume immediately when
distortions can be heard. When speakers are destroyed by overload, the
guarantee becomes void. The cabling of a 100 Volt system belongs to an
electrical installation which may only be carried out by a qualified
electrician!
The total load must not exceed the rated power of the amplifier. Before starting the installation, make clear how many speakers you want to install in the room and with what wattage(s), as overload will damage the amplifier and speaker.
CONNECTION OVERVIEW
TECHNICAL SPECIFICATION
| FCS5| FCS6| FCS8
---|---|---|---
Ref.nr.| 953.| 953.| 953.
Power Max.| 80W A 8 Ohm| 120W A 8 Ohm| 160W A 8 Ohm
Power RMS| 20W @ 8 Ohm| 30W @ 8 Ohm| 40W @, 8 Ohm
Tappings| 4, 10, 20W @100V/8Ohm| 7.5, 15, 30W @, 100V/8Ohm| 10, 20, 40W @
100V/8Ohm
Frequency response| 100Hz — 20kHz| 70Hz — 20kHz| 50Hz-20kHz
Woofer| 5.25″| 6.5″| 8″
Tweeter| 1″ Silk dome
SPL @, 1W/1m| 86dB| 88dB| 90dB
Mounting diameter| 1800mm| 2020mm| 2460mm
Mounting depth| 77mm| 100mm| 118mm
Dimensions| 2000 x 77mm| 2420 x 100mm| 2720 x 118mm
Weight| 0.65kg| 0.95kg| 1.1kg
The specifications are typical. The actual values can slightly change from one
unit to the other. Specifications can be changed without prior notice.
The products referred to in this manual conform to the European Community
Directives to which they are subject:
- Low Voltage (LVD) 2014/35/EU
- Electromagnetic Compatibility (EMC) 2014/30/EU
- Restriction of Hazardous Substances (RoHS) 2011/65/EU
Specifications and design are subject to change without prior notice.
www.tronios.com
Copyright © 2019 by Tronios The Netherlands
References
- Samen zijn we open. Samen staan we sterk. - Stichting Open
- Samen zijn we open. Samen staan we sterk. - Stichting Open
- Sound & Light distributor - Tronios.com
- Homepage - Wecycle
- Homepage - Wecycle
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>